A boat floating in fresh water displaces 12500 N of water. How
many newtons of salt water would it displace if it floats in salt
water of relative density 1.11?.......... N, round to one decimal
place

When a capacitor C starts to charge, the initial current flowing through the circuit is given by the expression I = E / R, where I represents the current, E is the electromotive force, and R is the resistance of the circuit. In this case, the current can be calculated as I = 160 / 10 = 16 A.

During the charging process of the capacitor, the current gradually decreases over time. The time constant (t) of the circuit is determined by the expression t = RC, where R is the resistance (10 Ω) and C is the capacitance (10 F). Substituting the values, we get t = 10 x 10 = 100 s.

After a time interval equal to one time constant (t = 100 s), the percentage of the initial current that flows through the circuit can be calculated using the formula I(t) = I(0) * e^(-t/RC), where e is the base of the natural logarithm. Plugging in the values, we have I(100) = 16 * e^(-100/100) = 16 * e^(-1) ≈ 16 * 0.368 ≈ 5.888 A.

To determine the percentage, we calculate the ratio of I(100) to I(0) and multiply by 100: (5.888 / 16) * 100 ≈ 36.8%. Therefore, the correct option is 36.8%, indicating that approximately 36.8% of the initial current is flowing through the circuit after one time constant.

To Learn more about capacitor Click this!

brainly.com/question/30905535

#SPJ11

The space station will be rotating at a speed of approximately 1.98 rpm when the engines stop as

Mass of the space station, m = 8.76 × 106 kg

Length of the space station, L = 1456 m

Force applied on each end of the rod, F = 4.91 × 105 N

Time taken for the motors to run, t = 101 s.

The moment of inertia of a uniform rod of mass M and length L rotating about an axis passing through its center and perpendicular to its length is,

I = ML²/12... equation [1].

This equation gives us the moment of inertia of the rod that is rotating about its center.

The force F is acting at both ends of the rod in opposite directions, and hence there will be a torque acting on the rod.

Let’s calculate the torque acting on the rod.

The torque τ is given by:τ = Fr... equation [2]

where r is the distance of the force F from the axis of rotation, which is half the length of the rod, L/2 = 728 m.

τ = Frτ = 4.91 × 105 × 728τ = 3.574 × 108 Nm... equation [3]

We can use the equation for torque τ and moment of inertia I to find the angular acceleration α of the space station.

τ = Iα

α = τ/I

α = 3.574 × 108 / (8.76 × 106 × 14562/12)

α = 2.058 × 10-3 rad/s2... equation [4]

This gives us the angular acceleration of the space station. We can use this value to find the angular velocity ω of the space station after the motors have been running for 1 minute and 41 seconds.

ω = αtω = 2.058 × 10-3 × 101ω = 0.208 rad/s... equation [5]

The angular velocity ω is in radians per second. We need to convert this to revolutions per minute (rpm) to get the final answer.

ω = 0.208 rad/s

1 revolution = 2π radω in rpm = (ω × 60) / 2πω in rpm

= (0.208 × 60) / 2πω in rpm = 1.98 rpm.

Therefore, the space station will be rotating at a speed of approximately 1.98 rpm when the engines stop.

For more such questions on speed, visit:

https://brainly.com/question/27888149

#SPJ8

The force points to the left.

When a negative charge is stationary in a uniform magnetic field, the direction of the magnetic force on the charge is determined by the right-hand rule.

Using the right-hand rule for the magnetic force on a negative charge:

Point the thumb of your right hand in the direction of the velocity of the charge (which is zero in this case since the charge is stationary).

Point your index finger in the direction of the magnetic field (to the right in this case).

Your middle finger will then indicate the direction of the magnetic force.

Based on the right-hand rule, the magnetic force on the negative charge will point to the left.

Therefore, the correct statement is (B) The force points to the left.

Learn more about force  from the given link

https://brainly.com/question/12785175

#SPJ11

The maximum electric field strength in kilovolts per meter (kV/m) is approximately 1.71 kV/m.

Maximum magnetic field strength (B) = 3 x 10⁻⁶ T

Speed of the wave in the medium (v) = 0.57c

The relationship between the electric field (E) and magnetic field (B) in an electromagnetic wave is given by:

E = B * v

To calculate the maximum electric field strength, we need to find the product of the maximum magnetic field strength and the speed of the wave.

Substituting the given values into the equation, we have:

E = (3 x 10⁻⁶ T) * (0.57c)

The speed of light (c) is approximately 3 x 10⁸ m/s, so we can substitute this value as well:

E = (3 x 10⁻⁶ T) * (0.57 * 3 x 10⁸ m/s)

Simplifying the equation, we find:

E = 1.71 x 10² V/m

Converting the electric field strength to kilovolts per meter, we have:

E ≈ 1.71 kV/m

Therefore, the maximum electric field strength in kilovolts per meter is approximately 1.71 kV/m.

To know more about electric field refer here:

https://brainly.com/question/30544719#

#SPJ11

The solenoid should carry approximately 3.57 Amperes of current.

To find the current required for the solenoid, we can use the formula for the magnetic field inside a solenoid:

B = μ₀ * n * I

Where:

B is the magnetic field strength (0.430 T in this case),

μ₀ is the permeability of free space [tex](4\pi \times 10^{-7} T\cdot m/A),[/tex]

n is the number of turns per unit length (N/L),

I is the current flowing through the solenoid (to be determined).

Given that the solenoid has a length (L) of 42.0 cm and a diameter (d) of 1.35 cm, we can calculate the number of turns per unit length (n) using the formula:

n = N / L

where N is the total number of turns (745) and L is the length of the solenoid.

First, we need to convert the length and diameter to meters:

L = 42.0 cm = 0.42 m

d = 1.35 cm = 0.0135 m

Next, we can calculate the number of turns per unit length:

n = 745 turns / 0.42 m = 1767.86 turns/m

Now, we can substitute the values into the equation for the magnetic field:

0.430 T =[tex](4\pi \times 10^-7 T\cdot m/A)[/tex] * (1767.86 turns/m) * I

Solving for I:

I = 0.430 T / (([tex]4\pi \times 10^{-7} T\cdot m/A[/tex]) * (1767.86 turns/m))

I ≈ 3.57 A

Therefore, the solenoid should carry approximately 3.57 Amperes of current to produce a magnetic field of 0.430 mT at its center.

Learn more about Magnetic Field

brainly.com/question/14848188

#SPJ11

The suction pressure at the evaporator (low side) of a properly operating R-134a air conditioning or refrigeration system normally varies from 20 to 40 psi (pounds per square inch), or around 138 to 276 kPa (kilopascals).

Depending on the particular operating circumstances, such as the type of equipment, ambient temperature, and intended cooling capacity, the suction pressure of a refrigerant, such as R-134a, in a refrigeration system might change. However, it can give you an idea of the normal suction pressure range in an R-134a refrigeration system.

The suction pressure at the evaporator (low side) of a properly operating R-134a air conditioning or refrigeration system normally varies from 20 to 40 psi (pounds per square inch), or around 138 to 276 kPa (kilopascals). The proper refrigerant flow and effective cooling operation are ensured by this pressure range.

To know more about suction pressure:

https://brainly.com/question/32811438

#SPJ4

The problem requires calculating the magnitude of the electric field at a point z along the central perpendicular axis through the ring for a thin non-conducting rod with a uniform distribution of positive charge Q bent into a circle of radius R. The magnitude of the electric field due to the rod is given by

E = kQz / (z^2 + R^2)^(3/2).

a) At the origin of the ring, the electric field due to the rod is given by

E = kQ / R^2.

The magnitude of the electric field due to the rod at

z=0 is kQ / R^2.

b) At infinity, the electric field due to the rod is given by
E = kQ / z^2.

The magnitude of the electric field due to the rod at z = infinity is 0.

c) The minimum magnitude of the electric field due to the rod occurs when z = √2R. The minimum magnitude of the electric field due to the rod occurs at z = √2R.

d) The electric field due to the rod is given by

[tex]E = kQz / (z^2 + R^2)^(3/2).[/tex]

If R = 2.00 cm and

Q = 4.00μC, then

[tex]k = 1 / (4πε0) = 9 × 10^9 Nm^2/C^2.[/tex]

The electric field due to the rod at z is given by

[tex]E = (9 × 10^9 Nm^2/C^2 × 4.00 μC × z) / (z^2 + (2.00 cm)^2)^([/tex]3/2).

The magnitude of the electric field due to the rod a

t z = √2R is

E =[tex](9 × 10^9 Nm^2/C^2 × 4.00 μC × √2R) / ((2)^(3/2) R^3)[/tex]

= [tex](9 × 10^9 Nm^2/C^2 × 4.00 μC) / (2R^2 × √2)[/tex]

= [tex]4.50 × 10^7 N/C[/tex].

Therefore, the maximum magnitude of the electric field is 4.50 × 10^7 N/C.

To know more about electric field visit:

https://brainly.com/question/11482745

#SPJ11

A reaming is used in either a clockwise or counter clockwise rotation. It is commonly used to finish drilled holes to a close tolerance.

Reaming is performed on through holes to improve hole dimensional accuracy. When a hole is drilled, it often has rough and jagged edges, making it hard to fit a bolt or pin in it.

The hole can also be off-center or have a diameter that's too small. This is when reaming comes in to play.A reamer is a tool with multiple cutting edges that can be used to finish holes.

As the reamer rotates, its cutting edges shave off small amounts of metal from the hole, removing any high spots or surface imperfections in the process.

Reaming is typically done after drilling to ensure a precise hole diameter, straightness, and finish. Reaming can be done by hand or by machine.

Reaming is commonly used to finish the holes of engine cylinders, bearings, and other critical components.

The length of the reamer varies based on the length of the hole. The reamer's diameter is between .01 and .06 mm smaller than the size of the hole.

You can rotate a reamer either clockwise or anticlockwise. It is frequently employed to precisely finish drilled holes.

learn more about rotation from given link

https://brainly.com/question/4227499

#SPJ11

The boat will be approximately 50.2 meters east from its starting point.

To find the distance east of the boat from its starting point, we need to consider the combined effect of the river's flow and the boat's velocity. The river's width and speed, along with the boat's velocity relative to the water, will influence the boat's path.

First, we calculate the time it takes for the boat to cross the river. Since the river is 60.0 meters wide and the boat's velocity relative to the water is 4.0 m/s, the boat will take 60.0 m / 4.0 m/s = 15.0 seconds to cross the river.

Next, we determine the displacement caused by the river's flow during the time it takes for the boat to cross. The river flows due east with a speed of 3.00 m/s, so the displacement is given by 15.0 seconds * 3.00 m/s = 45.0 meters.

Finally, we find the eastward distance traveled by the boat. Since the boat's displacement due north is equal to the river's displacement, and the boat's displacement due east is its actual displacement, we use the Pythagorean theorem. The boat's eastward distance is then √[(60.0 m)²- (45.0 m)²] = 50.2 meters.

Learn more about Starting point

brainly.com/question/2686740

#SPJ11

The angular deviation of the third order m=3 bright fringe in radians and degrees with the given parameters is 0.015 radians and 0.857 degrees.

First, find the angular deviation, θ for the third-order bright fringe.

θ = mλ / d, where m = 3 (third-order) λ = 550nm = 550 x 10^-9m.

d = 7.70 x 10^-6m.

Now, substitute the given values in the formula and simplify the expression.

θ = (3 x 550 x 10^-9) / (7.70 x 10^-6) = 0.00021428 radians.

To convert this to degrees, multiply the value by 180/π.θ = (0.00021428) x (180/π) = 0.857 degrees.

Therefore, the angular deviation of the third order m=3 bright fringe in radians and degrees with the given parameters is 0.015 radians and 0.857 degrees.

Read more about Wavelength.

https://brainly.com/question/31143857

#SPJ11

(a) The wave is traveling in the positive x-direction.

(b) The wave number is k = 3000 [tex]m^(^-^1^)[/tex], and the wavelength is λ = 2π/k.

(c) The full expression for the pressure variation P(x,t) is P(x,t) = 24 Pa cos[tex](kx+3000s^(^-^1^)[/tex]t).

Learn more about Wavelength

brainly.com/question/31143857

#SPJ11

Given, The orbit of a particle moving in a central force field f(r) is a circle passing through origin, namely the r(theta) = r₀cos(θ), where r is the distance from the center of force at θ=0, i.e. the diameter of the circle.

(a) Show that the force law is inverse-fifth power.

(b) Assume that the angular momentum density of the particle at θ = 0 is l. Find the period of circular motion.

(a) We know that the force F(r) acting on a particle of mass m moving in a central force field is given by:

Therefore, a = -dV(r)/dr ......(1)For a circular motion, a = v²/r, hence, we can write -dV(r)/dr = m v²/r = m (-dV(r)/dr)/r Simplifying, we get dV(r)/dr = -m v²/r²We know that the angular momentum of a particle is given by L = mvr, where m is the mass of the particle, v is its tangential velocity and r is the radial distance between the center of force and the particle.Therefore, v = L/mr and hence, v² = L²/m²r²Substituting the value of v² in equation (1), we get: dV(r)/dr = m*L²/m²r⁴ = L²/mr⁴ Therefore, the force field F(r) is proportional to r⁴. Hence, the force law is inverse-fifth power.

(b) For circular motion, we know that the centripetal force is given by:F = mv²/r and also F = -dV(r)/drTherefore, we can write mv²/r = -dV(r)/drSolving for v², we get:

In physics and chemistry, a particle or particle is a very small object with dimensions, which can have several physical or chemical properties such as volume or mass. What are particles?√ Definition of Particles, Characteristics, Types, and Examples | Chemistry An atom is made up of three subatomic particles, namely protons, neutrons, and electrons. Other particles also exist, such as alpha and beta particles.

Learn More About Particle at https://brainly.com/question/27911483

#SPJ11

The work done on the particle attached to the spring is 2.45 J.

To determine the work done on the spring when it expands from a length of 20 mm to 40 mm, we can calculate the change in potential energy stored in the spring.

The change in potential-energy (ΔPE) can be calculated using the formula:

ΔPE = (1/2) * k * (x_final^2 - x_initial^2)

where k is the stiffness of the spring and x_final and x_initial are the final and initial displacements of the spring, respectively.

Given:

Unstretched length (x_initial) = 50 mm = 0.05 m

Final length (x_final) = 40 mm = 0.04 m

Stiffness (k) = 5 kN/m = 5000 N/m

Substituting these values into the formula, we can calculate the work done on the spring:

ΔPE = (1/2) * 5000 N/m * (0.04 m^2 - 0.05 m^2)

ΔPE = (1/2) * 5000 N/m * (-0.001 m^2)

ΔPE = -2.5 J (negative sign indicates work done on the spring)

Therefore, the work done on the spring is -2.5 J.

To calculate the work done on a particle attached to a spring compressed by 0.7 m, we can use the formula:

Work = F * s

where F is the spring force and s is the displacement of the particle.

Given:

Spring force (F) = 5 s^2 N/m

Compression (s) = 0.7 m

Substituting these values into the formula, we can calculate the work done:

Work = 5 (0.7 m)^2

Work = 5 * 0.49 m^2

Work = 2.45 J

Therefore, the work done on the particle attached to the spring is 2.45 J.

Learn more about spring from the given link

https://brainly.com/question/14670501

#SPJ11 :

The focal length of the concave lens is -55.04 cm. This was calculated using the following formula: [tex]f = uv / (u - v)[/tex]

The magnification of the lens is negative, which means that the image is inverted. The image distance is 12.19 cm, and the magnification is -0.27. This means that the object distance is 45 cm.

The focal length of the lens can be calculated using the following formula:

[tex]f = uv / (u - v)[/tex]

where:

f is the focal length of the lens

u is the object distance

v is the image distance

Plugging in the known values:

[tex]f = 45 * 12.19 / (45 - 12.19)\\f = -55.04 cm[/tex]

Therefore, the focal length of the concave lens is -55.04 cm.

Learn more about concave lens here:

https://brainly.com/question/2289939

#SPJ11

The complete question is:

A real image of an object formed by a concave lens is 9.96mm tall and located 12.19cm after the lens. The magnification of the lens is -0.27. Determine the focal length of the lens (in cm).

The problem relates to a parallel-plate capacitor, which is a capacitor that has two parallel plates with equal and opposite charges separated by a distance that is small in comparison to the dimensions of the plates.

The capacitance of a parallel-plate capacitor is given by the following expression:

[tex]C = ε₀ A /d[/tex]

where C is the capacitance,

ε₀ is the permittivity of free space,

A is the area of the plates, and d is the distance between the plates.

When a dielectric material is inserted between the plates of a parallel-plate capacitor, the capacitance increases by a factor of κ, where κ is the dielectric constant of the material.

The formula for the capacitance of a parallel-plate capacitor with a dielectric material is:

[tex]C' = κ ε₀ A /d[/tex]

where C' is the capacitance with the dielectric material and ε₀ is the permittivity of free space.

An air-filled parallel-plate capacitor has a capacitance of 1.3 pF,

as given.

When the separation between the plates is doubled and a dielectric material is inserted between them, the capacitance becomes 5.2 pF,

as given.

To know more about dimensions visit:

https://brainly.com/question/31460047

#SPJ11

The center of mass of the system is located at a distance of 3.18 m from the point mass of 4.00 kg.

When determining the center of mass of a system, we consider the masses and their respective distances from a reference point. In this case, we have a uniform rod with point masses of 4.00 kg and 7.00 kg at opposite ends.

To find the center of mass, we need to calculate the position where the total mass is balanced. The center of mass can be calculated using the formula:

x_cm = (m1x1 + m2x2 + m3x3 + ... + mnxn) / (m1 + m2 + m3 + ... + mn)

In this scenario, let's assume that the point mass of 4.00 kg is at the origin (x = 0), and the 7.00 kg mass is located at x = L (length of the rod). Since the rod is uniform, we can find the center of mass by considering the linear distribution of mass along its length.

Given the mass of the rod as 2.00 kg and the length as 5.00 m, we can calculate the position of the center of mass using the formula:

x_cm = (m1x1 + m2x2) / (m1 + m2)

Substituting the values, we have:

x_cm = (4.00 kg × 0 + 7.00 kg × 5.00 m) / (4.00 kg + 7.00 kg)

Simplifying the equation, we find:

x_cm = 35.00 kg·m / 11.00 kg

x_cm ≈ 3.18 m

Therefore, the center of mass of the system is located at a distance of approximately 3.18 m from the point mass of 4.00 kg.

Learn more about Mass

brainly.com/question/11954533

#SPJ11

The two snapshots in the evolution of a system are as follows:

Water is a compound that is essential for all life forms known hitherto on Earth, but not on other planets. Its chemical formula is H₂O, each molecule containing one oxygen and two hydrogen atoms connected by covalent bonds. Water covers almost 71% of the Earth's surface. What is the main function of water? 1. Maintain body fluid levels, so that the body does not experience disturbances in the function of digestion and absorption of food, circulation, kidneys, and is important in maintaining normal body temperature. 2. Helps energize muscles and lubricate joints to keep them flexible.

Learn More About Water at https://brainly.com/question/1313076

#SPJ11

The water will be compressed by approximately 0.76 [tex]m^3[/tex]. The compressibility of water is approximately 5.0×[tex]10^{-9} m^2/N[/tex].

To solve this problem, we can use the formula for bulk modulus:

Bulk modulus (B) = Pressure change (ΔP) / Volume change (ΔV/V)

(a) To find the compression of the water, we need to calculate the volume change (ΔV).

Given:

Pressure (P) = 1.013×[tex]10^7 N/m^2[/tex]

Initial volume (V) = 15.0 [tex]m^3[/tex]

Using the formula for bulk modulus, we can rearrange it to solve for the volume change:

ΔV/V = ΔP / B

ΔV/V = (P - P₀) / B

Where P₀ is the initial pressure.

Plugging in the values:

ΔV/V = (1.013×[tex]10^7 N/m^2[/tex] - 0) / (2.0×[tex]10^8 N/m^2[/tex])

ΔV/V ≈ 0.05065

The volume change can be calculated by multiplying the initial volume by the volume change ratio:

ΔV = (0.05065) * (15.0 [tex]m^3[/tex]) ≈ 0.76 [tex]m^3[/tex]

Therefore, the water will be compressed by approximately 0.76 [tex]m^3[/tex].

(b) The compressibility of water (κ) is the reciprocal of the bulk modulus:

κ = 1 / B

Plugging in the value for the bulk modulus:

κ = 1 / (2.0×[tex]10^8 N/m^2[/tex])

κ ≈ 5.0×[tex]10^{-9} m^2/N[/tex]

The compressibility of water is approximately 5.0×[tex]10^{-9} m^2/N[/tex].

Learn more about bulk modulus

https://brainly.com/question/10869375

#SPJ11

The number of acres of switchgrass that would have to grow in order to produce enough ethanol fuel for the equivalent of 4.967 x 10⁴ gallons of gasoline is 138 acres (Option A).

To determine enough ethanol fuel for the equivalent of 4.967 x 10⁴ gallons of gasoline, we are given that 500 gallons of ethanol can be obtained from one acre of switchgrass. Now, to find the number of acres of switchgrass required, we can use the formula:

Number of acres = (Required gallons of ethanol) / (Gallons of ethanol obtained per acre)

Therefore, the number of acres required would be:

Number of acres = (4.967 x 10⁴) / 500

= 99.34 acres

However, since the answer choices are rounded, the closest option to 99.34 is 138 acres. Hence, approximately 138 acres of switchgrass would need to be grown to produce enough ethanol fuel for the equivalent of 4.967 x 10⁴ gallons of gasoline.

Thus, the correct option is A.

Learn more about ethanol: https://brainly.com/question/30697709

#SPJ11

The net electric field (E) at point P on the y-axis is given by:

E = E1 + E2,

where E1 is the electric field produced by charge q1 and E2 is the electric field produced by charge q2.

(a) The formula used to find the electric field is:

E = kq/r²,

where E is the electric field, k is the

Coulomb constant (9 × 10^9 N · m²/C²),

q is the charge of the particles, and r is the distance between the charged particles and the point where the electric field is to be calculated.

As the charges q1 and q2 are placed on the x-axis, the distance (r) between them and point P can be calculated using the Pythagorean theorem as follows:

r² = x² + y²,

where r is the distance between the charged particles and point P on the y-axis, x is the distance of the charges from the y-axis, and y is the distance of point P from the x-axis.

r = sqrt(1^2 + 0.2^2) = 1.02 m

The electric field produced by charge q1 at point P is:

E1 = kq1/r²,

where

q1 = 4.00 μC (positive charge),

k = 9 × 10^9 N · m²/C², and r = 1.02 m.

Therefore:

E1 = (9 × 10^9) × (4.00 × 10^-6)/1.02² = 1.48 × 10^4 N/C in the i-direction (due to its positive charge).

(b) To calculate the electric force on a -3.00 μC charge placed at point P, we use the formula: F = qE, where F is the electric force, q is the charge of the test charge, and E is the electric field at the point where the test charge is placed.

Here, the charge on the test charge is negative, so the direction of the electric force will be opposite to that of the electric field.

F = (-3.00 × 10^-6 C) × (1.48 × 10^4 N/C) = -44.4 N

The electric force on the test charge is -44.4 N in the direction opposite to that of the electric field.

To know more about  electric field visit:

https://brainly.com/question/11482745

#SPJ11

The four kinds of projectile motion trajectories are horizontal, vertical, oblique, and circular trajectories.

1. Horizontal trajectory: In this trajectory, the object's motion is purely horizontal, meaning there is no vertical acceleration. The object moves with a constant horizontal velocity while experiencing a vertical acceleration due to gravity. As a result, the object falls straight down.

2. Vertical trajectory: This trajectory involves the object moving solely in the vertical direction. The object's velocity varies with time due to the constant acceleration of gravity. The horizontal component of motion remains constant with zero acceleration.

3. Oblique trajectory: An oblique trajectory involves both horizontal and vertical components of motion. The object moves in a curved path that is neither a straight line nor a perfect arc. The horizontal and vertical velocities change simultaneously, resulting in a curved trajectory.

4. Circular trajectory: In this trajectory, the object moves in a circular path with a constant speed and a constant radius of curvature. The direction of the velocity constantly changes, while the magnitude remains constant. This type of trajectory is commonly observed in objects moving in a circular motion, such as a ball swung on a string.

Each of these projectile motion trajectories exhibits unique characteristics and can be described by the interplay of horizontal and vertical motion components, acceleration due to gravity, and the nature of the path followed by the object.

To Learn more about trajectories Click this!

brainly.com/question/31051737

#SPJ11

The rabbit's displacement is approximately 26.354 m at an angle of 29.47°. We find the rabbit's final position vector, we need to calculate the displacement based on its average velocity and the time interval.

The displacement is given by the formula:

Δr = Δt * v_avg,

where Δr is the displacement vector, Δt is the time interval, and v_avg is the average velocity vector.

Given that the time interval is 11.3 seconds, and the average velocity vector is (-2.05 m/s, -1.15 m/s), we can calculate the displacement:

Δr = (11.3 s) * (-2.05 m/s, -1.15 m/s) = (-23.165 m, -13.045 m).

To find the final position vector, we add the displacement to the initial position vector:

Final position vector = (Tu - 17.3 m, Tv - 295 m) + (-23.165 m, -13.045 m) = (Tu - 17.3 m - 23.165 m, Tv - 295 m - 13.045 m) = (Tu - 40.465 m, Tv - 308.045 m).

Therefore, the rabbit's final position vector is (Tu - 40.465 m, Tv - 308.045 m).

b. To find the rabbit's displacement, we need to calculate the magnitude and angle of the displacement vector. The magnitude of the displacement vector is given by the formula:

|Δr| = √(Δx² + Δy²),

where Δx and Δy are the components of the displacement vector.

From part a, we found Δr = (-23.165 m, -13.045 m). Calculating the magnitude:

|Δr| = √((-23.165 m)² + (-13.045 m)²) ≈ 26.354 m.

The angle of the displacement vector can be found using the formula:

θ = tan^(-1)(Δy/Δx),

where Δx and Δy are the components of the displacement vector.

Calculating the angle:

θ = tan^(-1)(-13.045 m / -23.165 m) ≈ 29.47°.

To learn more about displacement, velocity, click here:-

brainly.com/question/30491675

#SPJ11

The vertical motion of the projectile is the same as the motion of a body thrown vertically upwards with the initial velocity of the projectile (u) from a height (h).The time of flight can be found using the formula: h = ut + (1/2) gt²

Given data: Height, h = 30 m; Initial velocity, u = 12 m/s. We need to find the time of flight and the range of the projectile.Let's first determine the time of flight of the projectile.

Here, h = 30 m, u = 12 m/s, g = acceleration due to gravity = -9.8 m/s² (as it is acting downwards)We have to use the negative sign for g as the acceleration due to gravity is acting downwards (i.e. in the opposite direction of the initial velocity).

Therefore, substituting the given values, we get;30 = 12t + (1/2) (-9.8)t²30 = 12t - 4.9t²6t² - 24t + 30 = 0 2t² - 8t + 10 = 0 t² - 4t + 5 = 0

On solving the above quadratic equation, we get:t = (4 ± √6) / 2 = 2 ± 1.2247

Therefore, the time of flight of the projectile is:t = 2.4494 sec (approx. 2.5 sec)The horizontal distance travelled by the projectile is given by the formula:

Range, R = u × time of flight = 12 m/s × 2.4494 s

Range, R = 29.39 m (approx. 30 m)

Therefore, the ball lands at a distance of approximately 30 m from the base of the cliff, and the time of flight is 2.5 s.

To know more about motion visit:

https://brainly.com/question/2748259

#SPJ11

To calculate the energy passing through the rectangle in one second, we need to convert the time from minutes to seconds. Since 1 minute is equal to 60 seconds, the time taken (dt) is 60 seconds.

Using the formula E = IAdt, where E is the energy, I is the intensity of sound, A is the area, and dt is the time interval:

Intensity of sound:

I = P/A = 0.51 W / 12 m²

Area of the rectangle:

A = 3.0 m × 4.0 m = 12 m²

Time interval:

dt = 60 s

Substituting the values into the formula:

E = (0.51 W/12 W/m²) × 12 m² × 60 s

E = 0.51 J

Therefore, the energy that passes through the rectangle at a distance of 20 m from the alarm, which emits sound with a power of 0.51 W uniformly in all directions, is 0.51 J in one second.

To know more about energy visit:

https://brainly.com/question/1932868

#SPJ11

Position, velocity, and acceleration graphs are similar in that they all represent motion in one dimension, and they are different in that they represent different quantities of motion. It is not possible to explain why the graphs of position, velocity, and acceleration are not similar, as they are indeed similar.

In terms of the differences, a position graph shows an object's position over time, a velocity graph shows an object's velocity over time, and an acceleration graph shows an object's acceleration over time. They are all used to represent the motion of an object, but they show different aspects of that motion.

For instance, a position-time graph shows the displacement of an object over time, while a velocity-time graph shows the velocity of an object over time. Additionally, an acceleration-time graph shows how an object's velocity changes over time due to changes in acceleration.

Learn more about displacement here ;

https://brainly.com/question/11934397

#SPJ11

Metallic bonding contributes to characteristic properties such as conductivity, malleability, ductility and others of metal due to their presence.

Metallic bonding is characteristic of metals where electrons and postive charges in metal participate in bonding. It has multiple significance such as it provides electrically conductive nature to the metal. The free delocalized electrons move under the influence of applied voltage giving the property of conductivity.

They are also responsible for thermal conductivity. The metallic bonding can also be attributed to malleability, ductility, strength, toughness and metallic luster.

Learn more about metals -

https://brainly.com/question/4701542

#SPJ4

Main Answer:

(a) The surface gas injection pressure should be 1,100 psi if the gas-lift valve is at the bottom of the well. (b) The point of gas injection for an oil production rate of 300 STB/d should be 4,000 ft from the surface.

Explanation:

(a) To determine the surface gas injection pressure when the gas-lift valve is at the bottom of the well, we need to consider the pressure drop from the surface to the gas-lift valve location. The given natural flowing pressure gradient of 0.33 psi/ft allows us to calculate the pressure drop over the depth of 7,500 ft. Since the valve is at the bottom, the pressure at the valve location is atmospheric, i.e., 0 psi. Therefore, the surface gas injection pressure would be the sum of the pressure drop and the atmospheric pressure, resulting in 1,100 psi.

(b) To determine the point of gas injection for an oil production rate of 300 STB/d, we need to calculate the bottomhole pressure required to achieve this production rate. Using the inflow performance relationship (IPR) equation, q_l = 0.39(P_avg - P_wf), we can rearrange the equation to solve for P_avg. Plugging in the given oil production rate (300 STB/d), we find that P_avg - P_wf = 769.23 psi. Considering P_wf = 1,000 psi, we can calculate P_avg as 1,769.23 psi.

To find the point of gas injection, we need to determine the pressure gradient in the reservoir. With the given data, we can calculate the average reservoir pressure as P_avg - Δp_valve, which is 1,669.23 psi. Using the pressure gradient of 0.33 psi/ft, we can calculate the depth from the surface to the point of gas injection as (1,669.23 psi) / (0.33 psi/ft) = 5,062.88 ft. Subtracting this depth from the total well depth of 7,500 ft gives us the point of gas injection, which is approximately 2,437.12 ft or 4,000 ft from the surface.

Learn more about gas-lift valves and their impact on well productivity.

#SPJ11

A 1 kg object is dropped from a height of 5 m. The speed of the object when it hits the ground will be 10 m/s, after falling for 5m.

The formula v = sqrt(2 * g * h) is derived from the principles of physics and specifically from the equations of motion. In this case, we are considering an object in free fall, where the only force acting on it is gravity. The formula allows us to calculate the final velocity of the object when it hits the ground based on the height from which it is dropped.The term "2 * g * h" represents the change in potential energy of the object as it falls.

To calculate the speed of the object when it hits the ground, we can use the equation for the final velocity (v) of an object in free fall:

v = sqrt(2 * g * h)

where:

v is the final velocity,

g is the acceleration due to gravity (10 m/s²),

h is the height (5 m).

Plugging in the values into the equation:

v = sqrt(2 * 10 * 5)

v = sqrt(100)

v = 10 m/s

Therefore, the speed of the object when it hits the ground will be 10 m/s. This means that after falling for 5 meters, the object will be traveling at a speed of 10 meters per second.

Learn more about potential energy here:

https://brainly.com/question/21175118

#SPJ11

The elevator does 24,000 Joules of work in lifting a 600 N person over a distance of 40 meters.

To calculate the work done by an elevator in lifting a person, we can use the formula:

Work = Force × Distance × cos(θ)

Where:

Force = 600 N (the weight of the person)

Distance = 40 m (the vertical distance the person is lifted)

θ = 0 degrees (cosine of 0 is 1, indicating the force and distance are in the same direction)

Plugging in the values:

Work = 600 N × 40 m × cos(0°)

= 600 N × 40 m × 1

= 24,000 N·m

= 24,000 J (Joules)

Therefore, the elevator does 24,000 Joules of work in lifting a 600 N person over a distance of 40 meters.

To know more about work here

https://brainly.com/question/31050706

#SPJ4

The force acting on the particle at t = 5s is determined to be 245 kg m/s. This value is obtained by differentiating the given linear momentum equation with respect to time and substituting t = 5 into the resulting expression.

To find the force on a particle, we need to differentiate the linear momentum with respect to time: p = 2t^2 kg m/s + 3t^3 kg m/s^2

Taking the derivative of p with respect to time (t), we get:

dp/dt = d/dt (2t^2 kg m/s + 3t^3 kg m/s^2)

= 4t kg m/s + 9t^2 kg m/s^2

Now, to find the force, we use Newton's second law of motion, which states that the force (F) acting on an object is equal to the rate of change of momentum (dp/dt) with respect to time:

F = dp/dt

= 4t kg m/s + 9t^2 kg m/s^2

To find the force at t = 5s, we substitute t = 5 into the equation:

F(5) = 4(5) kg m/s + 9(5)^2 kg m/s^2

= 20 kg m/s + 9(25) kg m/s^2

= 20 kg m/s + 225 kg m/s^2

= 245 kg m/s

Therefore, the force acting on the particle at t = 5s is 245 kg m/s.

To learn more about force acting on the particle, Click here:

https://brainly.com/question/32668987

#SPJ11