White light is passed through a cloud of cool hydrogen gas and then examined with a spectroscope. The dark lines observed on a bright (coloured) background are caused by (d) hydrogen absorbing certain frequencies of the white light.
As the white light passes through a cloud of cool hydrogen gas, certain photons with the same amount of energy as the difference between two levels in the hydrogen atom are absorbed by the hydrogen gas. The energy level difference corresponds to a specific frequency or wavelength of light.
After the hydrogen atoms absorb the photons, they become excited and move to higher energy levels. Because these photons are absorbed, they are missing from the white light spectrum, resulting in a dark line in the absorption spectrum.
This absorption spectrum's dark lines indicate that certain colors or wavelengths of light are missing due to hydrogen absorption.
Learn more about spectrum here ;
https://brainly.com/question/32934285
#SPJ11
A thin, horizontal copper rod is 1.09 m long and has a mass of 31.1g. What is the minimum current in the rod that can cause it to float in a horizontal magnetic field of 2.29 T?
The minimum current that can cause a 1.09m long, horizontal copper rod with a mass of 31.1g to float in a horizontal magnetic field of 2.29T is 7.19A.
Here's how to arrive at the solution:
First, we need to find the magnetic force on the copper rod.
The formula for magnetic force on a current-carrying conductor in a magnetic field is:
F = BIL
Where:
F = magnetic force (N)B = magnetic field strength (T)I = current (A)L = length of the conductor (m)
From the given information:
B = 2.29 T (magnetic field strength)L = 1.09 m (length of the copper rod)
We need to find the minimum current I that will allow the copper rod to float, or in other words, allow the force of gravity to be balanced by the force due to the magnetic field.
So we set the force of gravity equal to the magnetic force and solve for I.mg = BIL
Where:
m = mass of the copper rod (kg)g = acceleration due to gravity (9.81 m/s²)
We convert the mass of the copper rod from grams to kilograms.
m = 31.1 g ÷ 1000 g/kg = 0.0311 kgS
ubstituting the given values and solving for I:
mg = BIL0.0311 kg × 9.81 m/s² = 2.29 T × 1.09 m × II = (0.0311 kg × 9.81 m/s²) ÷ (2.29 T × 1.09 m)I = 7.19 A
The minimum current that can cause the copper rod to float in the magnetic field is 7.19A.
To know more about horizontal visit :
https://brainly.com/question/29019854
#SPJ11
A 11 V battery pack converts 140 W of power. How much current flows through the battery pack?
when a 11 V battery pack converts 140 W of power then the amount of current that flows through the battery pack is 12.73 Amps. We can use the following equation to get the current passing through the battery pack: Power (P) is equal to voltage times current.
We may rewrite the equation to find the current if the power is 140 W and the voltage is 11 V: Power (P) x Voltage (V) equals Current (I). replacing the specified values: 140 W / 11 V is the current (I). By dividing 140 by 11, we get that the battery pack's current is roughly 12.73 Amperes (A).
to know more about voltage refer to the link below
https://brainly.com/question/27861305
#SPJ4
2. Twojects antially at the mese seconds Object has an initial velocity of 9.00 min nderpresa constant acceleration of 3.00 Object is initially at rest and under a constant acceleration of St. a) What is the distance between the objects at 100 de What is the distance between the objects when they have the same velocity? c) How long does it takes catch up hell what time ate the displacement the same How much for isbjecting an objects the time when they have undergone the same diaplacement
a) The distance between the objects at 100 seconds can be calculated using the kinematic equation: distance = initial velocity * time + (1/2) * acceleration * time^2.
b) The distance between the objects when they have the same velocity can be determined by finding the time it takes for the two objects to reach that velocity and then calculating the distance using the same kinematic equation.
c) The time it takes for one object to catch up with the other can be found by setting their distances equal to each other and solving for time.
a) To find the distance between the objects at 100 seconds, we can use the kinematic equation mentioned above. Plug in the values of initial velocity, time, and acceleration for each object and calculate the respective distances. Then subtract the distances to find the difference between the two objects.
b) To determine the distance when the objects have the same velocity, we need to find the time it takes for each object to reach that velocity. Once we have the time, we can use the kinematic equation to calculate the distance for each object. The difference between the distances will give us the answer.
c) When one object catches up with the other, their distances will be equal. Set the distances equal to each other and solve for time. Once you have the time, you can calculate the displacement for each object using the kinematic equation and find the difference.
It's important to note that the calculations above assume constant acceleration throughout the motion of the objects.
Learn more about initial velocity.
brainly.com/question/28395671
#SPJ11
in a standing wave areas of destructive interference are the
In a standing wave, areas of destructive interference are the locations where the crest of one wave coincides with the trough of another wave, resulting in the cancellation of amplitudes
A standing wave is formed when two waves of the same frequency and amplitude traveling in opposite directions interfere with each other. This interference creates specific patterns of nodes (points of no displacement) and antinodes (points of maximum displacement) along the medium in which the waves are traveling.
In a standing wave, areas of destructive interference occur at the nodes. These are the locations where the crest of one wave coincides with the trough of the other wave. As a result, the positive displacement of one wave cancels out the negative displacement of the other wave, resulting in the amplitude being reduced to zero at these points.
The formation of areas of destructive interference is due to the principle of superposition, which states that when two waves meet, the resulting displacement is the algebraic sum of their individual displacements. In the case of destructive interference, the displacements of the two waves are equal in magnitude but opposite in direction, causing them to cancel each other out.
The positions of the nodes and antinodes in a standing wave depend on the wavelength and the boundary conditions of the medium. These standing wave patterns can be observed in various systems, such as vibrating strings, sound waves in pipes, and electromagnetic waves in resonant cavities.
To know more about antinodes refer here:
https://brainly.com/question/30640087#
#SPJ11
Polarized light is incident on a sheet of polarizing material, and only 20% of the light gets through. Find the angle between the electric field and the material's trapsmission axis.
When only 20% of polarized light passes through a sheet of polarizing material, the angle between the electric field of the light and the material's transmission axis can be found by taking the inverse cosine of the square root of 0.20. This angle represents the orientation at which the light can transmit through the material effectively.
When polarized light passes through a sheet of polarizing material, the intensity of the transmitted light depends on the angle between the electric field of the light and the transmission axis of the material.
In this case, since only 20% of the light gets through, it means that the transmitted light has an intensity that is 20% of the incident light's intensity.
The intensity of polarized light is given by the equation:
I = I₀ * cos²θ
where I₀ is the incident light's intensity and θ is the angle between the electric field and the transmission axis.
Given that the transmitted light's intensity is 20% of the incident light's intensity, we can set up the following equation:
0.20 * I₀ = I₀ * cos²θ
By canceling out I₀ on both sides and taking the square root, we get:
√0.20 = cosθ
Simplifying further, we find:
cosθ = √0.20
To find the angle θ, we can take the inverse cosine (arccos) of both sides:
θ = arccos(√0.20)
Evaluating this expression will give us the angle between the electric field and the material's transmission axis.
To know more about polarized light refer to-
https://brainly.com/question/29217577
#SPJ11
Object A, which has been charged to +12nC, is at the origin. Object B, which has been charged to What is the magnitude of the electric force on object A ? −30nC, is at (x,y)=(0.0 cm,2.0 cm). Express your answer in newtons. Part B What is the magnitude of the electric force on object B ? Express your answer in newtons.
Object A, which has been charged to +12nC, is at the origin.Object B, which has been charged to −30nC, is at (x,y)=(0.0 cm,2.0 cm).
Formula for electric force is:
F = K * (q1 * q2 / [tex]r^2[/tex])
Where,q1 is the first charge,
q2 is the second charge,
K is Coulomb's constant and
r is the distance between the two charges.
From the given data, distance between the two charges is:
r =sqrt[tex](x^2 + y^2)[/tex]
r = sqrt[tex]((0-0)^2 + (2-0)^2)[/tex]
r = sqrt(4)
r = 2 cm
Now,Substituting the values in the above formula,
F = 9 × [tex]10^9[/tex] * (12 × [tex]10^{-9[/tex] × -30 × [tex]10^{-9[/tex]) / (2 × [tex]10^{-2[/tex])²
F = -162 N
Therefore, the magnitude of the electric force on object A is 162 N.
Part B : The electric force on object B can be found by using the same formula as above.
F = 9 × [tex]10^9[/tex] * (12 × [tex]10^{-9[/tex] × -30 × [tex]10^{-9[/tex]) / (2 × [tex]10^{-2[/tex])²
F = -162 N
The magnitude of the electric force on object B is also 162 N.
To know more about origin visit:
https://brainly.com/question/31317185
#SPJ11
open end and is used to cause the tube to resonate. (a) What are the wavelength (in in) and the frequency (in Hz ) of the fundaeneatal frequency? Wayelength frequency m. (b) What are the wavelength (i in m) and freauency { in Hz } of the first overtonet wivelenctit frequency
The wavelength of the first open-end wavelength frequency is 0.75 m.
A tube of length 0.75 m is open ended and is used to cause the tube to resonate.
(a) The fundamental frequency is the first harmonic frequency and can be calculated by using the formula:
f1 = (v/2L)
where,f1 = frequency
v = velocity
L = length
The velocity of sound in air at room temperature is approximately 343 m/s.
Converting the length of the tube from inches to meters: 0.75 m = 29.53 in
Therefore, the fundamental frequency of the tube is:
f1 = (343/2 x 0.75)
f1 = 228.67 Hz
Also, the wavelength can be calculated using the formula:
λ1 = 2L/n
where,λ1 = wavelength
n = harmonic number
For the fundamental frequency:
λ1 = 2 x 0.75/1
λ1 = 1.5 m
(b) The first open-end wavelength frequency is the second harmonic frequency, and can be calculated as:
f2 = (2v/L)
where,f2 = frequency
v = velocity
L = length
The frequency can be calculated as:
f2 = (2 x 343/0.75)= 914.67 Hz
The wavelength can be calculated using the formula:
λ2 = 2L/n
where,λ2 = wavelength
n = harmonic number
For the first open-end wavelength frequency:
λ2 = 2 x 0.75/2
λ2 = 0.75 m
Therefore, the wavelength of the first open-end wavelength frequency is 0.75 m.
Learn more about the wavelength from the given link-
https://brainly.com/question/16051869
#SPJ11
why does relative humidity increase at night and decrease during the day?
The change in relative humidity throughout the day and night is primarily influenced by two factors: temperature and the diurnal cycle of atmospheric moisture.
The relative humidity refers to the amount of water vapor present in the air compared to the maximum amount of water vapor the air can hold at a particular temperature. The change in relative humidity throughout the day and night is primarily influenced by two factors: temperature and the diurnal cycle of atmospheric moisture.
During the day, as the Sun heats the Earth's surface, the temperature rises. Warmer air can hold more water vapor, so the air's capacity to hold moisture increases. However, this does not necessarily mean that the actual amount of water vapor in the air increases proportionally. As the air warms up, it becomes less dense and can rise, leading to vertical mixing and dispersion of moisture. Additionally, the warmer air can enhance the evaporation of water from surfaces, including bodies of water and vegetation. These processes tend to result in a decrease in relative humidity during the day.
At night, the opposite occurs. As the Sun sets and the temperature drops, the air cools down. Cooler air has a lower capacity to hold moisture, so the relative humidity tends to increase. The cooler air reduces the rate of evaporation and allows moisture to condense, leading to an accumulation of water vapor in the air. The reduced temperature also lowers the air's ability to disperse moisture through vertical mixing. As a result, relative humidity tends to be higher during the night.
It's important to note that local geographic and meteorological conditions can also influence relative humidity patterns, so variations may occur depending on the specific location and climate.
To know more about relative humidity here
https://brainly.com/question/10849972
#SPJ4
A mercury thermometer bulb has a volume of 0.200 cm3 . The capillary tube above the bulb has a crosssectional diameter of 0.120 mm. How much does the mercury rise in the tube when the temperature increases from 10°C to 32°C?
The rise in the mercury level in the capillary tube of a thermometer, when the temperature increases from 10°C to 32°C, is approximately 5.75 cm.
To determine the rise in the mercury level in the capillary tube of a thermometer, we can use the principle of thermal expansion. The change in volume of the mercury is related to the change in temperature and the coefficient of volume expansion of mercury.
Volume of the bulb (V) = 0.200 cm³
Cross-sectional diameter of the capillary tube (d) = 0.120 mm
First, we need to calculate the cross-sectional area of the capillary tube.
Area (A) = π * (d/2)²
Since the diameter is given in millimeters, we need to convert it to centimeters:
d = 0.120 mm = 0.012 cm
Substituting the values into the formula for the area:
A = π * (0.012 cm/2)²
A ≈ 0.000113 cm²
Next, we need to calculate the change in volume of the mercury using the coefficient of volume expansion of mercury. The coefficient of volume expansion for mercury is approximately 0.000181 °C⁻¹.
Change in volume (ΔV) = V * α * ΔT
Where:
V = Volume of the bulb
α = Coefficient of volume expansion of mercury
ΔT = Change in temperature
Substituting the values into the formula:
ΔV = 0.200 cm³ * 0.000181 °C⁻¹ * (32 °C - 10 °C)
ΔV ≈ 0.000651 cm³
Finally, we can calculate the rise in the mercury level by dividing the change in volume by the cross-sectional area of the capillary tube:
Rise in mercury level = ΔV / A
Rise in mercury level ≈ 0.000651 cm³ / 0.000113 cm²
Rise in mercury level ≈ 5.75 cm
Therefore, the mercury rises approximately 5.75 cm in the capillary tube when the temperature increases from 10°C to 32°C.
To know more about thermal expansion, refer to the link below:
https://brainly.com/question/28528249#
#SPJ11
a change in which of the following will affect the buoyant force experienced by an object that is totally submerged in a liquid?
Density of the fluid and volume of the body immmerse in it will affect the buoyant force experienced by an object that is totally submerged in a liquid.
Hence, the correct option is D.
A change in the following factors will affect the buoyant force experienced by an object that is totally submerged in a liquid:
a) Weight of the fluid displaced: The buoyant force is equal to the weight of the fluid displaced by the submerged object. Therefore, the weight of the fluid displaced, which is determined by the volume of the object submerged and the density of the fluid, will affect the buoyant force.
b) Density of the fluid: The buoyant force is directly proportional to the density of the fluid. If the density of the fluid changes, it will affect the buoyant force acting on the object.
c) Volume of the object submerged: The buoyant force is directly proportional to the volume of the object submerged in the fluid. If the volume of the object changes, it will result in a change in the buoyant force.
d) Mass of the fluid displaced: The buoyant force is also equal to the mass of the fluid displaced. This is determined by the volume of the object submerged and the density of the fluid.
So, to summarize, changes in the weight of the fluid displaced, the density of the fluid, the volume of the object submerged, or the mass of the fluid displaced will affect the buoyant force experienced by an object that is totally submerged in a liquid.
Hence, the correct option is D.
The given question is incomplete and the complete question is '' a change in which of the following will affect the buoyant force experienced by an object that is totally submerged in a liquid?
a. weight of the immersed in it
b. shape of the body immersed in the fluid
c. density of the fluid ande mass of the body immmerse in it.
d. density of the fluid and volume of the body immmerse in it.
To know more about buoyant force here
https://brainly.com/question/13944626
#SPJ4
The charges deposited on each plate of a square parallel-plate air capacitor of capacitance 220pF are 0.150µC. The plates are 00.126mm apart. What is the potential difference in Volts between the plates?
The potential difference between the plates of a square parallel-plate capacitor can be calculated using the formula V = Q/C, where V is the potential difference.
Q is the charge deposited on each plate, and C is the capacitance. By substituting the given values, we can determine the potential difference in volts.
The formula for the potential difference between the plates of a capacitor is V = Q/C, where V represents the potential difference, Q is the charge on each plate, and C is the capacitance. Given that the capacitance of the capacitor is 220 pF (picoFarads) and the charge on each plate is 0.150 µC (microCoulombs), we can substitute these values into the formula to find the potential difference.
However, before we can calculate the potential difference, we need to convert the capacitance and charge to their SI units. 1 pF is equivalent to 1 × 10⁻¹² F, and 1 µC is equivalent to 1 × 10⁻⁶ C. After converting the units, we can substitute the values into the formula to determine the potential difference in volts.
Therefore, by applying the formula V = Q/C and performing the necessary unit conversions and calculations, we can find the potential difference in volts between the plates of the square parallel-plate air capacitor.
Learn more about plates of a square here:
https://brainly.com/question/29084023
#SPJ11
The ______ technique uses a radio frequency wave to excite hydrogen atoms in the brain to create an image of the living human brain.
The technique that uses a radio frequency wave to excite hydrogen atoms in the brain to create an image of the living human brain is called magnetic resonance imaging (MRI).
MRI is a non-invasive medical imaging technique that provides detailed structural and functional information about the brain. It relies on the principle of nuclear magnetic resonance (NMR), which involves the behavior of atomic nuclei in a magnetic field.
During an MRI scan, the patient is placed inside a strong magnetic field, which aligns the hydrogen atoms in the body, particularly those in water molecules, in a specific direction. Radio frequency pulses are then applied, causing the hydrogen atoms to absorb and emit energy. These emitted energy signals are detected by the MRI machine and used to construct a detailed image of the brain.
By analyzing the signals from different regions of the brain, MRI can produce high-resolution images that reveal the brain's anatomical structures and detect abnormalities or pathologies. It is widely used in clinical settings for diagnosing various conditions, such as tumors, strokes, multiple sclerosis, and traumatic brain injuries. Additionally, functional MRI (fMRI) can also be performed to study brain activity by measuring blood flow changes associated with neural activity, enabling researchers to map brain functions and understand cognitive processes.
To know more about functional MRI click this link-
https://brainly.com/question/21405582
#SPJ11
X=A+B+A+C Use De-Morgan's theorems to turn this into a form suitable for implementing solely in NAND gates and draw the circuit diagram. [8]
The inputs A, B, and C are connected to NAND gates. The outputs of the NAND gates are connected to another set of NAND gates, which produce the final output X.
To implement the expression X = A + B + A + C using only NAND gates and applying De Morgan's theorem, we can follow these steps:
Step 1: Apply De Morgan's theorem to convert the OR operation into NAND operations.
X = (A'·B')'·(A'·C')'
Step 2: Apply De Morgan's theorem again to convert the AND operations into NAND operations.
X = ((A'·B')')'·((A'·C')')'
Step 3: Simplify the expression using the NAND operations.
X = (A''+B'')'·(A''+C'')'
Step 4: Further simplify the expression using double negation.
X = (A+B)'·(A+C)'
Now, we have the expression X = (A+B)'·(A+C)' in a form suitable for implementing solely in NAND gates.
Circuit diagram:
```
_______
| |
A ---| NAND---(X)
|_______|
|
B -------|
|
A ---| NAND
|_______|
|
C -------|
|
|_______|
```
In the circuit diagram, the inputs A, B, and C are connected to NAND gates. The outputs of the NAND gates are connected to another set of NAND gates, which produce the final output X.
To know more about NAND gates click here:
https://brainly.com/question/29437650
#SPJ11
Parta - Fart Part: B What horizontal force is requied if μ
k
is zerve? se Evaluation Exprass yout answer to two significant figures and inclide the appropriate units.
The problem can be solved by applying Newton's laws of motion.
Here are the steps that can be followed;
Step 1: Draw a Free Body Diagram of the given system.
Step 2: Resolve the forces in x and y direction.
Step 3: Find out the acceleration of the system using the equation Fnet = ma. (Where Fnet is the net force acting on the system).
Step 4: Find the force of friction using the equation of friction f = μN. (Where μ is the coefficient of friction and N is the normal force).
Step 5: Now, using the horizontal force required, calculate the net force acting on the system in the horizontal direction.
Step 6: Compare this with the force of friction. If the net force is greater than the force of friction, the system will move. If it is less than the force of friction, the system will not move.
Step 7: Finally, if the horizontal force required is equal to the force of friction, the system will be in equilibrium.Now, let's apply these steps to solve the given problem. A horizontal force is applied to a 4 kg block placed on a horizontal surface. The coefficient of friction between the block and the surface is 0.4.
To know more about applying visit:
https://brainly.com/question/32426328
#SPJ11
a ____ is a physical path or a frequency used for signal transmissions.
A channel is a physical path or a frequency used for signal transmissions.
A channel refers to a physical path or frequency used to send signals or communications between devices. It is the medium through which a message is sent from one location to another. A radio station, for example, uses a channel to transmit a signal to the radio. Furthermore, a cable television network uses a channel to transmit signals to televisions through cable lines.A channel may also refer to a specific communication path between two or more computers in a network. Every network device, such as switches, routers, and bridges, is assigned a specific channel. A channel can also refer to the frequency on which a network operates.
To learn more about frequency visit: https://brainly.com/question/254161
#SPJ11
ANSWER ALL QUESTIONS Q1. 30 marks Two tanks are initially filled with air initially at a temperature To = 300 K and pressure po = 1 bar. Tank 1 has a volume of Vi = 2 mº, and the temperature of its contents is maintained at T1 = 300 K; tank 2 has a volume of V2 = 1 m, and the temperature of its contents is maintained at T2 = 300 K. At time t = 0, a compressor is turned on which feeds air at po and To into into tank 1 at a volumetric flow rate of Vin = 0.3 m min-!. Air flows from tank 1 to tank 2 at a molar flow rate given by the difference in pressure between the two tanks Ni = K (PI-pa), where Ki = 1 mols-bar-l. Air also leaves tank 2 to the surroundings at a flow rate N2 = K2(p2 - po), where K2 = 1 mol s-bar-l, and pos = 1 bar. Air can be considered an ideal gas, PV = NRT, where p is pressure, V is volume, N is the number of moles, R = 8.314 J mol-'K' is the gas constant, 7 is the absolute temperature. P Tout of moles of air within tank 2 (8 marks) (b) Clearly state the initial conditions for each of the differential equations derived above.
Main Answer:
(a) The total number of moles of air within tank 2 can be calculated by using the ideal gas equation and considering the initial conditions of pressure, volume, and temperature. By rearranging the equation PV = NRT and solving for N (number of moles), the answer can be obtained.
(b) The initial conditions for the differential equations derived above are as follows: tank 1 is initially filled with air at a volume of 2 m³ and a temperature of 300 K, while tank 2 is initially filled with air at a volume of 1 m³ and a temperature of 300 K. The pressure in both tanks is initially 1 bar.
Explanation:
(a) To determine the total number of moles of air within tank 2, we can use the ideal gas equation PV = NRT. Rearranging the equation to solve for N (number of moles), we have N = PV / RT. Considering the initial conditions provided in the question (pressure po = 1 bar, volume V2 = 1 m³, and temperature T2 = 300 K), we can substitute these values into the equation and calculate the number of moles of air in tank 2.
(b) The initial conditions for the differential equations refer to the starting values of the variables involved in the system. In this case, tank 1 has an initial volume (Vi) of 2 m³ and a temperature (T1) of 300 K, while tank 2 has an initial volume (V2) of 1 m³ and a temperature (T2) of 300 K. Additionally, both tanks have an initial pressure (po) of 1 bar. These initial conditions serve as the basis for formulating the differential equations that describe the changes in pressure, volume, and temperature over time.
Learn more about:
The ideal gas equation (PV = NRT) is a fundamental relationship used to describe the behavior of gases. It relates the pressure, volume, temperature, and number of moles of a gas. Understanding how to apply this equation allows for the analysis of various gas processes, including changes in pressure, volume, and temperature. Differential equations, on the other hand, are mathematical equations that involve derivatives and describe how variables change with respect to one another. In this problem, the initial conditions provide the starting values for the differential equations that model the air flow and conditions within the tanks.
#SPJ11
(b) A body of 800Kg is subjected to a force of 80 N, which brings it to rest within a distance of 50 m. Find the starting velocity and the time taken to come to rest.
The starting velocity of the body is 20 m/s and it takes 31.6 seconds to come to rest.
To solve the problem, we can use the equation of motion:
v^2 = u^2 + 2as
where v is the final velocity (which is 0 m/s since the body comes to rest), u is the initial velocity, a is the acceleration, and s is the distance traveled.
Force (F) = 80 N
Mass (m) = 800 kg
Distance (s) = 50 m
we need to calculate the acceleration (a) using Newton's second law:
F = ma
a = F/m
a = 80 N / 800 kg
a = 0.1 m/s²
we can use the equation of motion to find the initial velocity (u):
0^2 = u^2 + 2(0.1)(50)
0 = u^2 + 10
u^2 = -10
Since velocity cannot be negative in this context, we discard the negative solution and take the positive square root:
u = √10 ≈ 3.16 m/s
Therefore, the starting velocity of the body is approximately 3.16 m/s.
Next, we can determine the time taken to come to rest using the equation of motion:
v = u + at
0 = 3.16 + (0.1)t
0.1t = -3.16
t = -3.16 / 0.1
t = -31.6 s
Since time cannot be negative in this context, we discard the negative solution.
Hence, the time taken for the body to come to rest is approximately 31.6 seconds.
To know more about velocity, refer here:
https://brainly.com/question/24259848#
#SPJ11
If the current is given by i(t)=t+1 (A), then find the quantity of charge (in C) that flows through a cross section between t=0 and t=12 s.
The quantity of charge that flows through the cross section between t = 0 and t = 12 s is 78 Coulombs (C).
To find the quantity of charge (Q) that flows through a cross section between t = 0 and t = 12 s, we need to integrate the current (i) with respect to time (t) over the given time interval.
The quantity of charge flowing through the cross section is given by:
Q = ∫(i(t) dt)
Given i(t) = t + 1 A, the integral becomes:
Q = ∫(t + 1) dt
Integrating with respect to t:
Q = (1/2)t^{2} + t + C
Evaluating the integral over the given time interval [0, 12]:
Q = [(1/2)(12)^2 + 12] - [(1/2)(0)^2 + 0]
Q = (1/2)(144 + 12)
Q = 78 C
Therefore, the quantity of charge that flows through the cross section between t = 0 and t = 12 s is 78 Coulombs (C).
To know more about charge, refer here:
https://brainly.com/question/31979621#
#SPJ11
The Surface Scattering are accelerated the Verticle field and mobility, The positive and In ionized the Carriers. the due electrons Grate crashing against G real impurities, lattice Vibrations, interface, and roughness. at from other current from the Scattering lowers Limit. To (lin) = It _ I` = 9 w Uz (not T-njt') when electrons the surface by toward component of the electric to that its reduction in are alt Monted the keep bouncing Surface Oxide / silicon ballistic occurs field; They by against the oxide MOSFET, Carriers scatter from and fore
Surface scattering in a MOSFET (metal-oxide-semiconductor field-effect transistor) occurs when electrons collide with impurities, lattice vibrations, interfaces, and roughness on the surface of the device. These collisions disrupt the motion of electrons and result in a decrease in their mobility and an increase in the vertical electric field. Positive ions and negatively charged carriers (holes) are also involved in this process. Surface oxide and silicon play a crucial role in scattering the carriers, causing them to bounce off and change direction. The reduction in electron mobility due to surface scattering imposes a limit on the performance of the MOSFET.
Surface scattering is a phenomenon that affects the behavior of electrons in a MOSFET. When electrons move across the surface of the device, they can collide with impurities, lattice vibrations, interfaces between different materials, and surface roughness. These collisions disrupt the smooth motion of electrons, causing them to scatter and change direction.
The scattering process results in a reduction in the mobility of electrons, which refers to their ability to move through the device. The collisions also lead to an increase in the vertical electric field within the device.
Positive ions and negatively charged carriers, known as holes, are involved in the scattering process as well. These carriers can also collide with impurities and lattice vibrations, contributing to the overall scattering effect.
Surface oxide and the silicon material of the MOSFET play a significant role in scattering the carriers. The presence of oxide layers on the surface can cause the carriers to bounce off and change direction, further affecting their movement.
The scattering phenomenon sets a limit on the performance of the MOSFET because it reduces the mobility of electrons, which affects their ability to conduct current efficiently. To mitigate the negative effects of surface scattering, device designers and engineers employ various techniques to optimize the device structure and minimize surface roughness, aiming to improve the overall performance of MOSFETs.
To know more about scattering click here:
https://brainly.com/question/31960699
#SPJ11
Person A is walking toward a building at 0.47 m/s and is 3.0m away from the entrance. Person B is on top of the 50.0m building and drops a ball off the roof. The ball will land 1.0m in front of the entrance. The initial velocity of the ball is 0.00 m/s. Will the ball land on Person A?
Answer:
We can start by determining the time it takes for the ball to fall from the top of the building to the ground. We can use the equation:
y = 0.5gt^2
where y is the vertical distance traveled by the ball, g is the acceleration due to gravity (approximately 9.8 m/s^2), and t is the time. The initial vertical velocity of the ball is 0 m/s, since it is dropped from rest. The vertical distance traveled by the ball is the height of the building, which is 50.0 m. Substituting these values, we get:
50.0 m = 0.5(9.8 m/s^2)t^2
t = √(50.0 m / (0.5 × 9.8 m/s^2))
t = 3.19 s (to two decimal places)
So, it takes approximately 3.19 seconds for the ball to fall from the top of the building to the ground.
Next, we can determine the horizontal distance traveled by Person A during this time. The horizontal distance is given by:
d = vt
where d is the distance traveled, v is the velocity, and t is the time. Substituting the given values, we get:
d = (0.47 m/s)(3.19 s)
d = 1.50 m (to two decimal places)
So, Person A moves approximately 1.50 meters horizontally during the time it takes for the ball to fall from the top of the building to the ground.
Since the ball lands 1.0 meter in front of the entrance, and Person A is 3.0 meters away from the entrance, the ball will not land on Person A. Therefore, Person A is safe from the falling ball.
Explanation:
Two identical positive charges, 25.1 cm apart, exert forces of magnitude 9.2 N on each other. What is the value of the charge in micro-Coulombs?
According to Coulomb's law, the magnitude of the electric force between two point charges is given by:
F = kq₁q₂/r²
Where,F = forcek = Coulomb's constantq₁ and q₂ = magnitudes of the chargesr = distance between the two charges
Since the two identical charges exert forces of magnitude 9.2 N on each other, the force on each charge can be represented as:
F = kq²/r²where q = magnitude of the charge we can write:
kq²/r² = 9.2 NThus, the value of the charge in Coulombs will be:
q = sqrt(Fr²/k)Substituting the values,
q = sqrt(9.2 N x (0.251 m)²/ (9 x 10⁹ Nm²/C²)) = 2.91 × 10⁻⁶ C or 2.91 µC
The value of the charge in micro-Coulombs is 2.91 µC.
To know more about Coulomb's visit:
https://brainly.com/question/15167088
#SPJ11
In the railroad freight yard, an empty freight car of mass m rolls along a straight level track at 1.00 m/s and collides with an initially stationary, fully loaded boxcar of mass 5.30m. The two cars couple together on collision.
What is the speed of the two cars after the collision?
Suppose instead that the two cars are at rest after the collision. With what speed was the loaded boxcar moving before the collision if the empty one was moving at 1.00 m/s?
The velocity of the boxcar before the collision was 5.30 m/s. Let the empty freight car have a mass of m and let the fully loaded boxcar have a mass of 5.30m.
Let us denote the speed of the empty freight car before the collision as v1 and the speed of the boxcar before the collision as v2. Let the velocity of both the cars after the collision be v.
Conservation of momentum states that the momentum of a system remains constant if no external forces act on it. Therefore, we can equate the total momentum of the system before and after the collision.
Before the collision, the total momentum is:mv1 + 5.30m×0 = m × v
After the collision, the total momentum is:(m + 5.30m) × v.
Thus,mv1 = (m + 5.30m) × vV1 = (m + 5.30m) × v / m ————(1)
Now, let's assume that the two cars are at rest after the collision.
Therefore, the total momentum after the collision will be zero.
Thus, we get:(m + 5.30m) × v = 0v = 0.
This means the velocity of the two cars is zero after the collision.
Now, we need to find the velocity of the boxcar before the collision if the empty one was moving at 1.00 m/s.
We can use equation (1) to solve for v1.
Thus, we get:v1 = (m + 5.30m) × v / m= 5.30m × 1.00 m/s / m= 5.30 m/s.
Therefore, the velocity of the boxcar before the collision was 5.30 m/s.
Learn more about momentum here ;
https://brainly.com/question/30677308
#SPJ11
A cylinder made out of Steel has a radius of 4.0 mm±0.1 mm and a length of 150 mm±4 mm at a temperature of 15
∘
C±0.3
∘
C Use table 19.1 in Katz to find the coefficients of linear exansion, a, for a given material. If a range is given for α, use the lowest value. Assume that the thermal expan What is the change in length of the the cylinder after it has been cooled to a temperature of −36
∘
C±0.3
∘
C? ΔL=−0.099 mm (2.s.f) (3.33 points) What is the absolute uncertainty in this change in length?
The absolute uncertainty in the change in length of the cylinder is 0.001 mm.
To calculate the change in length of the cylinder, we need to consider the coefficient of linear expansion (α) of the steel material. The coefficient of linear expansion represents how much the length of a material changes per degree Celsius of temperature change. We can use Table 19.1 in Katz's book to find the coefficient of linear expansion for steel.
Given that a range is provided for α, we need to use the lowest value. Let's assume the coefficient of linear expansion for steel is α = 12 × 10^(-6) °C^(-1) (lowest value from the table).
The change in length (ΔL) can be calculated using the formula:
ΔL = α * L * ΔT
Where:
ΔL = Change in length
α = Coefficient of linear expansion
L = Initial length of the cylinder
ΔT = Change in temperature
Substituting the given values into the formula:
ΔL = (12 × 10^(-6) °C^(-1)) * (150 mm) * (15 °C - (-36 °C))
Calculating this expression gives us ΔL = -0.099 mm (to 3 significant figures).
The absolute uncertainty in the change in length is equal to the absolute uncertainty in the coefficient of linear expansion (α). Since the coefficient of linear expansion is given with a specific value, the absolute uncertainty is 0.001 mm.
To learn more about cylinder, click here: https://brainly.com/question/27853279
#SPJ11
8. _______ produced in the thermocouple due to difference of
junction temperature.
a) E.M.Fb)
Currentc)
Resistanced)
a & b are correcte)
c & a are correct
The correct answer is a) E.M.F. An electromotive force (E.M.F.) is produced in the thermocouple due to the difference in junction temperature.
In a thermocouple, two dissimilar metals are joined at the junctions. When there is a temperature difference between the two junctions, it creates a potential difference, or electromotive force (E.M.F.), across the thermocouple. This E.M.F. is a result of the Seebeck effect, which is the phenomenon of a voltage being generated when there is a temperature gradient along a conductor.
The E.M.F. generated in the thermocouple is directly proportional to the temperature difference between the junctions. It can be measured and utilized for various applications, such as temperature sensing and control. By measuring the E.M.F., the temperature at one junction can be determined relative to the other junction or a reference temperature.
Learn more about thermocouple here:
https://brainly.com/question/31473735
#SPJ11
At the instant that the traffic light tums green a truck at rest at the intersection starts to move due east with a constant acceleration of 4.00 m/s
2
. At the same instant a car traveling at a constant speed of 12.0 m/s passes the truck. How fast is the truck traveling when it overtakes the car? (a) 12 m/s (b) 18 m/s (c) 24 m/s (d) 30 m/s (e) none of the above answers
The answer is (a) 12 m/s. The truck is traveling at a speed of 12 m/s when it overtakes the car.
To solve this problem, we need to find the time it takes for the truck to catch up to the car. Once we have the time, we can determine the speed of the truck at that moment.
Let's assume the time it takes for the truck to catch up to the car is t. During this time, the car has traveled a distance equal to its speed multiplied by t, which is given as 12.0 m/s * t.
The truck, on the other hand, has undergone constant acceleration. We can use the kinematic equation: s = ut + (1/2)at^2, where s is the distance traveled, u is the initial velocity, a is the acceleration, and t is the time.
Since the truck starts from rest, its initial velocity u is 0 m/s. The distance traveled by the truck is the same as the distance traveled by the car, so we can set these two expressions equal to each other:
12.0 m/s * t = (1/2) * 4.00 m/s^2 * t^2
Simplifying this equation, we get:
6t = 2t^2
Dividing both sides by t, we have:
6 = 2t
t = 3 seconds
Now, we can find the speed of the truck at that moment by using the equation v = u + at, where u is the initial velocity, a is the acceleration, and t is the time:
v = 0 m/s + 4.00 m/s^2 * 3 s
v = 12 m/s
Therefore, the answer is (a) 12 m/s. The truck is traveling at a speed of 12 m/s when it overtakes the car.
Learn more about constant acceleration here:
https://brainly.com/question/29135987
#SPJ11
Charge of uniform density (90nC/m
3
) is distributed throughout a hollow cylindrical region formed by two coaxial cylindrical surfaces of radii 1.0 mm and 6.0 mm. Determine the magnitude of the electric field (in N/C ) at a point which is 2.5 mm from the symmetry axis.
In summary, by considering the charge enclosed by the Gaussian surface and applying Gauss's law, we can determine the magnitude of the electric field at a point 2.5 mm from the symmetry axis of the hollow cylindrical region
To determine the magnitude of the electric field at a point 2.5 mm from the symmetry axis of the hollow cylindrical region, we can use Gauss's law and symmetry arguments.
Gauss's law states that the electric field through a closed surface is proportional to the charge enclosed by that surface. In this case, we can consider a cylindrical Gaussian surface of radius 2.5 mm centered on the symmetry axis.
Since the charge distribution is uniform throughout the cylindrical region, the electric field will also have radial symmetry. This means that the electric field will only have a component in the radial direction and will be independent of the azimuthal angle.
The charge enclosed by the Gaussian surface is the difference between the charge enclosed by the outer cylindrical surface and the charge enclosed by the inner cylindrical surface.
The charge enclosed by the outer surface is given by:
Q_outer = charge density * volume of outer cylindrical region
= (90 nC/m^3) * π * (6.0 mm)^2 * (2.5 mm)
The charge enclosed by the inner surface is given by:
Q_inner = charge density * volume of inner cylindrical region
= (90 nC/m^3) * π * (1.0 mm)^2 * (2.5 mm)
The net charge enclosed is then:
Q = Q_outer - Q_inner
Now, we can apply Gauss's law to find the magnitude of the electric field. Gauss's law states that the electric field multiplied by the surface area of the Gaussian surface is equal to the net charge enclosed.
The surface area of the Gaussian surface is:
A = 2πrh, where r is the radius of the Gaussian surface (2.5 mm) and h is the height of the Gaussian surface (which can be chosen appropriately).
Using Gauss's law, we have:
E * A = Q
E * 2πrh = Q
Rearranging the equation, we can solve for the magnitude of the electric field:
E = Q / (2πrh)
Substituting the values of Q, r, and h, we can calculate the magnitude of the electric field at the given point.
In summary, by considering the charge enclosed by the Gaussian surface and applying Gauss's law, we can determine the magnitude of the electric field at a point 2.5 mm from the symmetry axis of the hollow cylindrical region. The result will be obtained by dividing the net charge enclosed by the surface area of the Gaussian surface.
Learn more about electric field here:
https://brainly.com/question/29427458
#SPJ11
A wheel with a radius of 0.39 m is mounted on a frictionless, horizontal axle that is perpendicular to the wheel and passes through the center of mass of the wheel. The moment of inertia of the wheel about the given axle is 0.031 kg・m2. A light cord wrapped around the wheel supports a 3.3 kg object. When the object is released from rest with the string taut, calculate the acceleration of the object in the unit of m/s2.
The acceleration of the object, when released with the string taut, is approximately 5.06 m/s^2.
To calculate the acceleration of the object when it is released, we can use the principle of rotational dynamics. The torque exerted by the hanging mass causes an angular acceleration, which in turn leads to a linear acceleration of the object.
The torque (τ) exerted on the wheel can be calculated using the formula:
τ = Iα
Where:
τ is the torque
I is the moment of inertia of the wheel
α is the angular acceleration
The torque exerted by the hanging mass can be expressed as:
τ = r * F
Where:
r is the radius of the wheel
F is the force exerted by the hanging mass
Since the force exerted by the hanging mass is equal to the weight (mg) of the mass, where g is the acceleration due to gravity, we have:
τ = r * mg
Equating the two torque equations, we have:
r * mg = Iα
Solving for α:
α = (r * mg) / I
The linear acceleration (a) of the object can be related to the angular acceleration by the formula:
a = rα
Substituting the value of α:
a = r * [(r * mg) / I]
Given:
r = 0.39 m (radius of the wheel)
m = 3.3 kg (mass of the object)
g = 9.8 m/s^2 (acceleration due to gravity)
I = 0.031 kg·m^2 (moment of inertia of the wheel)
Substituting these values into the equation:
a = 0.39 * [(0.39 * 3.3 * 9.8) / 0.031]
Calculating:
a = 0.39 * 12.97
a ≈ 5.06 m/s^2
Therefore, the acceleration of the object, when released with the string taut, is approximately 5.06 m/s^2.
Learn more about acceleration here:
https://brainly.com/question/30660316
#SPJ11
Two −2.7×10
−9
−C charged point-like objects are separated by 0.20 m. - Part A Determine the potential (assuming zero volts at infinity) at a point halfway between the objects. Express your answer with the appropriate units. - Part B Determine the potential (assuming zero volts at infinity) at a point 0.20 m to the side of one of the objects (and 0.40 m from the other) along a line joining them. Express your answer with the appropriate units.
The potential at a point halfway between two point-like objects is -5400 V (volts) while the potential at a point 0.20 m to the side of one of the objects (and 0.40 m from the other) along a line joining them is -13.5 kV (kilo volts).
A positive work done implies that the potential energy has increased, while negative work done implies that the potential energy has decreased.
The potential energy at a point p in the field of two point charges Q1 and Q2 separated by a distance r is given as follows;
Vp = k(Q1/r1 + Q2/r2) where k = 1 / 4πε0, ε0 is the permittivity of free space and r1 and r2 are the distances from p to Q1 and Q2 respectively.
The point halfway between the two charges is equidistant from each of them and at the mid-point between them.
Using the above formula, the potential energy is given by
Vp = k(Q1/r1 + Q2/r2)where Q1 = Q2 = -2.7 × [tex]10^-9[/tex] C, r1 = r2 = 0.10 m and k = 1 / 4πε0.
From the above equation,Vp = 8.99 × [tex]10^9[/tex] × (-2.7 × [tex]10^-9[/tex] / 0.1 + (-2.7 × [tex]10^-9[/tex]/ 0.1))= -5.4 × [tex]10^3[/tex] V
The potential at a point 0.20 m to the side of one of the objects (and 0.40 m from the other) along a line joining them can be calculated as follows:
Vp = k(Q1/r1 + Q2/r2) where Q1 = -2.7 × [tex]10^-9[/tex] C, Q2 = -2.7 × [tex]10^-9[/tex]C, r1 = 0.2 m and r2 = 0.4 m.
From the above equation,
Vp = 8.99 × 10^9 × (-2.7 × [tex]10^-9[/tex] / 0.2 - 2.7 × [tex]10^-9[/tex] / 0.4)= -1.35 × [tex]10^4[/tex] V.
Therefore, the potential at a point halfway between two point-like objects is -5400 V (volts) while the potential at a point 0.20 m to the side of one of the objects (and 0.40 m from the other) along a line joining them is -13.5 kV (kilo volts).
Learn more about work done here ;
https://brainly.com/question/32263955
#SPJ11
A certain physical quantity, P is calculated using formula P=5AB(B-C)2, what will be the SI
unit and the value of P? Consider your A in kg and B and C are in m/s.
A=85
B=95
C=195
[tex]P=5AB(B-C)² where A = 85 kg, B = 95 m/s, C = 195 m/s[/tex]To find the SI unit of P, we need to substitute the values of A, B, and C in the given equation.
[tex]P=5AB(B-C)² , P = 5 × 85 kg × (95 m/s – 195 m/s)²= 5 × 85 kg × (–100 m/s)²= 5 × 85 kg × (10,000 m²/s²)= 4,250,000 kg.m²/s²The SI unit of P is kg.m²/s².[/tex]
To find the value of P, we can substitute the values of A, B, and C in the given equation
[tex]P=5AB(B-C)²P = 5 × 85 kg × (95 m/s – 195 m/s)²= 5 × 85 kg × (–100 m/s)²= 5 × 85 kg × 10,000 m²/s²= 4,250,000 kg.m²/s² , the value of P is 4,250,000 kg.m²/s².[/tex]
To know more about equation visit:
https://brainly.com/question/29657983
#SPJ11
please show work
8. A plastic disk of radius 15 cm is spinning at 130 rpm. What is the magnitude of the centripetal acceleration of the outer rim of the disk?
The magnitude of the centripetal acceleration of the outer rim of the disk is approximately 27,819[tex]cm^2/s^2[/tex] or approximately 278.19 [tex]m^2/s^2[/tex]. The centripetal acceleration of the outer rim of a spinning disk can be calculated using the formula a = [tex](v^2)[/tex] / r, where v is the linear velocity of the rim and r is the radius of the disk.
First, we need to convert the given angular velocity from rpm to radians per second. Since 1 revolution is equal to 2π radians, we can calculate the angular velocity as follows:
Angular velocity = (130 rpm) * (2π radians/1 min) * (1 min/60 s) = 13.65 radians/s.
Next, we need to find the linear velocity of the outer rim of the disk. The linear velocity is equal to the circumference of the disk multiplied by the angular velocity. The circumference of the disk can be calculated using the formula 2πr, where r is the radius of the disk:
Circumference = 2π * (15 cm) = 30π cm.
Linear velocity = (30π cm) * (13.65 radians/s) = 409.5π cm/s.
Finally, we can calculate the centripetal acceleration using the formula a = [tex](v^2)[/tex]/ r:
Centripetal acceleration =[tex](409.5π cm/s)^2[/tex] / (15 cm) = 8841.86π [tex]cm^2/s^2[/tex]
The magnitude of the centripetal acceleration of the outer rim of the disk is approximately 27,819 [tex]cm^2/s^2[/tex] or approximately 278.19 [tex]m^2/s^2[/tex].
Learn more about centripetal acceleration here:
brainly.com/question/8825608
#SPJ11