Thus, the amount of charge delivered to the ground by the lightning bolt is 232.3 coulombs (C).
An especially violent lightning bolt has an average current of 1[tex].15 × 10³[/tex]
A, lasting 0.202 s.
To determine the amount of charge delivered to the ground by the lightning bolt, we can use the formula
Q = I × t
where Q is the charge, I is the current, and t is the time.
Substituting the given values,
we have Q =[tex]1.15 × 10³ A × 0.202 s[/tex]
Q =[tex]232.3 C[/tex]
To know more about violent visit:
https://brainly.com/question/27409768
#SPJ11
We use monochromatic light of Wavelength λ=5.90×10^−7m in a double slit experiment. Wefind that the fourth-order constructive interference occurs at an angle of 6.0^∘ . Now I want you to answer the following: (a) The required slit separation to achieve this result, and (b) the angle at which third-order Constructive interference will occur if We use the same slits but with a different light whose wavelength λ=6.50×10 ^−7m.
a) The required slit separation to achieve the fourth-order constructive interference at an angle of 6.0° with monochromatic light of wavelength λ=5.90×10⁻⁷m is approximately 9.83×10⁻⁶m.
b) With a different light source having a wavelength λ=6.50×10⁻⁷m, the angle at which third-order constructive interference will occur using the same slits is approximately 7.13°.
a) In a double-slit experiment, the condition for constructive interference is given by the equation: d × sin(θ) = m × λ,
where d is the slit separation, θ is the angle of the interference pattern, m is the order of the interference, and λ is the wavelength of the light.
Given that the fourth-order constructive interference occurs at an angle of 6.0° (converted to radians: 6.0° × π/180 ≈ 0.105 radians) and the wavelength is λ=5.90×10⁻⁷m, we can rearrange the equation to solve for the slit separation:
d = (m × λ) / sin(θ),
d = (4 × 5.90×10⁻⁷m) / sin(0.105),
d ≈ 9.83×10⁻⁶m.
b) Using the same slits but with a different light source having a wavelength λ=6.50×10⁻⁷m, we can determine the angle at which third-order constructive interference occurs. Rearranging the equation as before:
θ = arcsin((m × λ) / d),
θ = arcsin((3 × 6.50×10⁻⁷m) / 9.83×10⁻⁶m),
θ ≈ 7.13°.
To know more about monochromatic light refer here:
https://brainly.com/question/32064872#
#SPJ11
A 4.60 g bullet moving at 632 m/s strikes a 710 g wooden block at rest on a frictionless surface. The bullet emerges, traveling in the same direction with its speed reduced to 436 m/s. (a) What is the resulting speed of the block? m/s (b) What is the speed of the bullet-block center of mass? m/s
To solve this problem, we can apply the principle of conservation of momentum. To find the resulting speed of the block, we need to determine the velocity of the block after the collision.
we can write the equation for conservation of momentum in the x-direction as:
(m_bullet * v_bullet_initial) + (m_block * v_block_initial) = (m_bullet * v_bullet_final) + (m_block * v_block_final)
where:
m_bullet = mass of the bullet = 4.60 g = 0.0046 kg
v_bullet_initial = initial velocity of the bullet = 632 m/s
m_block = mass of the block = 710 g = 0.710 kg
v_bullet_final = final velocity of the bullet = 436 m/s
Substituting the known values into the equation and solving for v_block_final, we get:
(0.0046 kg * 632 m/s) + (0.710 kg * 0 m/s) = (0.0046 kg * 436 m/s) + (0.710 kg * v_block_final)
0.0029072 kg·m/s = 0.0020056 kg·m/s + (0.710 kg * v_block_final)
0.0009016 kg·m/s = 0.710 kg * v_block_final
v_block_final = 0.0009016 kg·m/s / 0.710 kg
v_block_final ≈ 0.00127 m/s
(b) The speed of the bullet-block center of mass can be calculated using the conservation of momentum equation in the x-direction:
(m_bullet * v_bullet_initial) + (m_block * v_block_initial) = (m_bullet + m_block) * v_center_of_mass
we have:
(0.0046 kg * 632 m/s) + (0.710 kg * 0 m/s) = (0.0046 kg + 0.710 kg) * v_center_of_mass
2.9152 kg·m/s = 0.00531 kg * v_center_of_mass
v_center_of_mass = 2.9152 kg·m/s / 0.00531 kg
v_center_of_mass ≈ 549.055 m/s
To know more about momentum follow:
https://brainly.com/question/30677308
#SPJ11
Each of the following statements about the electric field in a conductor at equilibrium was written by a different student. Select all hose that are physically correct. At equilibrium the electric field inside a polarized conductor due to the charges accumulated at the surface of the conductor is zero, so the net electric field inside the conductor is equal to the electric field due to charges in the surroundings. At equilibrium the electric field inside a polarized conductor due to the charges accumulated at the surface of the conductor is zero, and the electric field due to charges in the surroundings cannot penetrate the conductor, so the net electric field inside the conductor must be zero. At equilibrium the net electric field inside a conductor must be zero, because if it were not zero, there would be charge flow because the drift speed of the mobile charges is proportional the the net electric field. At equilibrium the net electric field inside a conductor must be zero, because the average drift speed of the mobile charges is
v
ˉ
=uE
net
, and the only way for
v
ˉ
to be zero is if E
net
=0. At equilibrium the electric field inside a conductor at equilibrium is zero because electric fields due to charges in the surroundings cannot penetrate the material of the conductor. At equilibrium the net electric field inside a conductor is zero because the conductor polarizes until the electric field inside the conductor due to charges at the surface is equal and opposite to the electric field due to charges in the surroundings.
At equilibrium the electric field inside a polarized conductor due to the charges accumulated at the surface of the conductor is zero, so the net electric field inside the conductor is equal to the electric field due to charges in the surroundings.
At equilibrium the electric field inside a polarized conductor due to the charges accumulated at the surface of the conductor is zero, and the electric field due to charges in the surroundings cannot penetrate the conductor, so the net electric field inside the conductor must be zero.
At equilibrium the net electric field inside a conductor must be zero, because the average drift speed of the mobile charges is v ˉ =uE net , and the only way for v ˉ to be zero is if E net =0. At equilibrium the net electric field inside a conductor is zero because the conductor polarizes until the electric field inside the conductor due to charges at the surface is equal and opposite to the electric field due to charges in the surroundings.
When an electric field is applied to a conductor, the free charges inside the conductor experience an electric force. The charges move and keep moving until the charge redistribution due to the motion of charges results in the elimination of the electric field inside the conductor.At this point, the redistribution of charges inside the conductor stops, and the conductor is said to have reached its electrostatic equilibrium.
During this equilibrium, there is no further movement of charges. Therefore, no current flows through the conductor.Therefore, only the following four statements are correct:At equilibrium the electric field inside a polarized conductor due to the charges accumulated at the surface of the conductor is zero, so the net electric field inside the conductor is equal to the electric field due to charges in the surroundings.
At equilibrium the electric field inside a polarized conductor due to the charges accumulated at the surface of the conductor is zero, and the electric field due to charges in the surroundings cannot penetrate the conductor, so the net electric field inside the conductor must be zero.
At equilibrium the net electric field inside a conductor must be zero, because the average drift speed of the mobile charges is v ˉ =uE net , and the only way for v ˉ to be zero is if E net =0.
At equilibrium the net electric field inside a conductor is zero because the conductor polarizes until the electric field inside the conductor due to charges at the surface is equal and opposite to the electric field due to charges in the surroundings.
Learn more about electric field here ;
https://brainly.com/question/11482745
#SPJ11
Pressure of a oil ( specific gravity = 0.86) at any section of a
pipe is 2 bar. Pressure head is
1.
23.71 m
2.
2 m
3.
20 m
4.
20.39 m
Pressure of a oil ( specific gravity = 0.86) at any section of a pipe is 2 bar. Pressure head is 23.71 m (Option A).
The pressure head is the vertical distance that a fluid column would rise due to the pressure at a given point. It is calculated by dividing the pressure by the product of the acceleration due to gravity (g) and the specific weight of the fluid (γ).
Let's assume the density of water is 1000 kg/m³. The density of the oil can be calculated as follows:
Density of oil = Specific gravity * Density of water = 0.86 * 1000 kg/m³ = 860 kg/m³
Now, to calculate the pressure head, we need to convert the pressure from bar to pascals (Pa) since pressure is typically measured in SI units.
1 bar = 100,000 Pa
Given that the pressure at the section of the pipe is 2 bar, the pressure can be converted to pascals as follows:
Pressure = 2 bar = 2 * 100,000 Pa = 200,000 Pa
Next, we can calculate the pressure head using the formula:
Pressure head = Pressure / (Density of oil * Acceleration due to gravity)
Acceleration due to gravity (g) is approximately 9.8 m/s².
Pressure head = 200,000 Pa / (860 kg/m³ * 9.8 m/s²) ≈ 23.71 meters
Therefore, the correct answer is 23.71 m.
Learn more about Pressure head here:
https://brainly.com/question/30450960
#SPJ11
The nucleus of 8 Be, which consists of 4 protons and 4 nectrons, is very unstable and spontaneously breaks into two alpha particies (helium nuclei, each consisting of 2 proeons and 2 . neutrons). (a) What is the force between the two alpha particles when they are 3.60×10−15 m apart? X. Youf response differs significantly from the correct answer. flework your solution from the beginning and check each step carefuily. N (b) What is the initial magnitude of the acceleration of the alpha particles due to this force? Note that the mass of an aipha particie is 4.0026 u. x Your response differs significantly from the correct answer, Rework your solution from the beginning and check each step carefully, mis?
The magnitude of the acceleration of the alpha particles is 3.5 × 10¹⁴ m/s².The charge on an alpha particle is 3.2 × 10⁻¹⁹ C. The distance between them is 2.3 × 10⁻¹² N.
(a) The electric force acting between two alpha particles is given as:F = k(q1q2)/r² where q1 and q2 are the charges of alpha particles, r is the separation between them, and k is Coulomb's constant.
The alpha particle consists of 2 protons, each having a charge of +1.6 × 10⁻¹⁹ C.
Therefore, the charge on an alpha particle is 2 × 1.6 × 10⁻¹⁹ C = 3.2 × 10⁻¹⁹ C.
The distance between them is 3.6 × 10⁻¹⁵ m.F = (9 × 10⁹ Nm²/C²) × [(3.2 × 10⁻¹⁹ C)²]/(3.6 × 10⁻¹⁵ m)²F = 2.3 × 10⁻¹² N
(b) The force between the two alpha particles causes an acceleration in them.
We can use the second law of motion to find the acceleration.a = F/m where m is the mass of one alpha particle.
The mass of an alpha particle is 4.0026 u = 6.65 × 10⁻²⁷ kg.a = (2.3 × 10⁻¹² N)/(6.65 × 10⁻²⁷ kg)a = 3.5 × 10¹⁴ m/s².
Therefore, the magnitude of the acceleration of the alpha particles is 3.5 × 10¹⁴ m/s².
Learn more about electric force here ;
https://brainly.com/question/20935307
#SPJ11
A radioactive nucleus has a half-life of 5×10^8 years. Suppose a sample of rock (say, in an asteroid) solidified right after the solar system formed. Then approximately what fraction of the radioactive element should be left in the rock today?
Given that a radioactive nucleus has a half-life of 5 × 108 years. Let's suppose that a sample of rock (say, in an asteroid) solidified right after the solar system formed.
Then we have to calculate the fraction of the radioactive element that should be left in the rock today.
Half-life (t₁/₂) of a radioactive substance is defined as the time taken by a substance to reduce to half its initial value.
This is given by the formula,N(t) = N₀(1/2)⁽ᵗ/ᵗ₁/₂⁾ Where,N(t) = Final quantity N₀ = Initial quantity t = Time elapsed t₁/₂ = Half-life period.
We know that the half-life (t₁/₂) of the radioactive nucleus is 5 × 108 years. Hence, the fraction of the radioactive element left can be calculated as follows:After the first half-life, the quantity of the radioactive element left would be N₀/2.
After the second half-life, it would be N₀/4 and so on.
Thus, the general formula for the quantity of the radioactive element left would be,N = N₀ (1/2)n Where n is the number of half-lives elapsed.
The fraction of the radioactive element left is given as,N/N₀ = (1/2)n.
Now, we can substitute the values in the above formula.
Let's suppose that one-half-life is 5 × 108 years. Then the age of the rock would be approximately 4.6 × 109 years (age of the Solar System).
Thus, the number of half-lives elapsed would be given by,n = (time elapsed)/(half-life)n = (4.6 × 109)/(5 × 108) = 9.2.
After 9.2 half-lives, the fraction of the radioactive element left would be,N/N₀ = (1/2)⁹.²≈ 0.00077 ≈ 7.7 × 10⁻⁴.
Thus, approximately 0.077% (7.7 × 10⁻⁴) of the radioactive element should be left in the rock today.
Learn more about asteroid here ;
https://brainly.com/question/18726579
#SPJ11
2) You are watching a jet ski race. A racer speeds up from rest to 70mph in just a few seconds, then continues at a constant speed. Draw the motion diagram, the position versus time graph, the velocity vs time graph and the acceleration vs time graph for the jet ski.
These diagrams represent the motion of the jet ski as described in the problem, starting from rest, accelerating to a constant speed, and then maintaining that speed.
Motion Diagram:
The motion diagram shows the position of the jet ski at different time intervals. Since the jet ski starts from rest, we can represent it as follows:
Constant Speed
The "o" represents the starting position of the jet ski, and the arrow indicates the direction of motion. As time progresses, the jet ski moves to the right.
Position vs. Time Graph:
Since the jet ski starts from rest and then continues at a constant speed, the position vs. time graph would be a straight line with a positive slope (representing constant velocity). The graph would look like this:
markdown
Velocity vs. Time Graph:
The velocity vs. time graph would show the change in velocity as a function of time. Since the jet ski starts from rest and then maintains a constant speed, the graph would be a step function. It would show an instant increase in velocity from zero to a constant value and then remain constant. The graph would look like this:
markdown
Acceleration vs. Time Graph:
Since the jet ski starts from rest and then maintains a constant speed, the acceleration vs. time graph would be zero throughout. It would be a horizontal line at zero acceleration. The graph would look like this:
markdown
Acceleration
These diagrams represent the motion of the jet ski as described in the problem, starting from rest, accelerating to a constant speed, and then maintaining that speed.
To know more about acceleration
https://brainly.com/question/460763
#SPJ4
A motorcycle is traveling up one side of a hill and down the other side. The crest of the hill is a circular arc with a radius of 59.7 m. Determine the maximum speed that the cycle can have while moving over the crest without losing contact with the road. v=
Let v be the maximum speed that the motorcycle can have while moving over the crest without losing contact with the road.
Since the hill's crest is a circular arc with a radius of 59.7 m,
its weight W can be resolved into two components: a radial force W cos θ that is perpendicular to the road and a tangential force W sin θ that is parallel to the road.Let's now take a look at the forces acting on the motorcycle. The forces that act on the motorcycle are the gravitational force W, the centripetal force F, and the force of friction f.
As a result, the following equation can be used to find the maximum speed that the motorcycle can have while moving over the crest without losing contact with the road:
`Ff = mv²/r`where `m` is the mass of the motorcycle and `r` is the radius of the circular arc of the hill.
We can calculate the radial component of the weight as
`W cos θ = mg cos θ`, where `m` is the mass of the motorcycle and `g` is the acceleration due to gravity, which is approximately 9.8 m/s².
Substituting `W cos θ` and `W sin θ` into the equation for `Ff`, we have:
`f = µW cos θ` and `F = W sin θ`
Substituting these equations into the equation for `Ff`, we have:
`µmg cos θ = mv²/r - mg sin θ`
Simplifying this expression yields:
`v² = rg(µ cos θ - sin θ)`
Substituting the given values, we have:
`v² = (59.7 m)(9.8 m/s²)(0.9) = 522.7 m²/s²`
Therefore, the maximum speed that the cycle can have while moving over the crest without losing contact with the road is:
`v = sqrt(522.7 m²/s²) = 22.85 m/s`
To know more about gravitational force visit:
https://brainly.com/question/32609171
#SPJ11
An elevator filled with passengers has a mass of 1583 kg.
(a)
The elevator accelerates upward from rest at a rate of 1.20 m/s2 for 1.75 s. Calculate the tension in the cable (in N) supporting the elevator.
(b) The elevator continues upward at constant velocity for 8.72 s. What is the tension in the cable
(in N) during this time?
(c)
The elevator decelerates at a rate of 0.600 m/s2 for 3.50 s. What is the tension in the cable (in N) during deceleration?
(d) How high has the elevator moved above its original starting point, and what is its final velocity? (Enter the height in m and the final velocity in m/s.)
The tension in the cable supporting the elevator is 1900 N. The tension in the cable supporting the elevator during constant velocity is 15520 N. The tension in the cable supporting the elevator during deceleration is 14680 N. The elevator has moved 2.73 m above its original starting point, and its final velocity is 2.1 m/s.
(a) The acceleration is given as 1.20 m/s² and
time t = 1.75 s.
To find the tension in the cable supporting the elevator we use the formula:
Tension = mass × acceleration
Tension = 1583 × 1.2
Tension = 1899.6 N
Tension ≈ 1900 N
Therefore, the tension in the cable supporting the elevator is 1900 N.
(b) The elevator moves upward at constant velocity, so the net force acting on it is zero. Hence the tension in the cable supporting the elevator is equal to the weight of the elevator, which is given by:
Tension = mass × g
Tension = 1583 × 9.8
Tension = 15520.4 N
Tension ≈ 15520 N
Therefore, the tension in the cable supporting the elevator during constant velocity is 15520 N.
(c) During deceleration, the acceleration is negative and its magnitude is given as 0.600 m/s².
The tension in the cable supporting the elevator is given by:
Tension = mass × (g - acceleration)
Tension = 1583 × (9.8 - 0.6)
Tension = 14680.4 N
Tension ≈ 14680 N
Therefore, the tension in the cable supporting the elevator during deceleration is 14680 N.
(d) Using the formula:v = u + at
The final velocity (v) of the elevator can be calculated as:
v = u + at
v = 0 + 1.2 × 1.75
v = 2.1 m/s
To find the height the elevator has moved, we use the formula:
s = ut + 1/2 at²
The initial velocity (u) of the elevator is 0 and the time taken to reach the final velocity (v) is 1.75 s.
Therefore,s = (1/2) × 1.2 × (1.75)²
s = 2.73125 m
s ≈ 2.73 m
Thus, the elevator has moved 2.73 m above its original starting point, and its final velocity is 2.1 m/s.
Learn more about the velocity from the given link-
https://brainly.com/question/80295
#SPJ11
an electrically charged object can be used to attract:
An electrically charged object can be used to attract any object with an opposite charge.
This is due to the fundamental principle that opposites attract and repel in physics.
Electric charge is a fundamental property of matter that gives rise to electromagnetic interactions. An electric charge, whether positive or negative, produces an electric field that surrounds it. This field exerts a force on any other charge in its vicinity that is either attracted to or repelled from it. Electric charge is a fundamental property of matter that produces a variety of electric phenomena. When the charge is concentrated in a localized region of space, the object is electrically charged. When there is a net accumulation of charge in an object, it becomes electrically charged. An electrically charged object produces an electric field in its vicinity, which exerts a force on other charged objects. An electrically charged object can be used to attract objects with an opposite charge or repel objects with the same charge.
To know more about electric charge please refer to:
https://brainly.com/question/2373424
#SPJ11
Standing waves of frequency 57 Hz are produced on a string that has mass per unit length 0.0160 kg/m. With what tension must the string be stretched between two supports if adjacent nodes in the standing wave are to be 0.71 meters apart?
The tension for a desired standing wave, use the wave equation and wave velocity equation. Given the distance between adjacent nodes and frequency, the tension is approximately 105.33 Newtons.
The tension required to produce the desired standing wave, we can use the wave equation:
v = √(F/μ)
where v is the wave velocity, F is the tension in the string, and μ is the linear mass density of the string.
The wave velocity is given by the equation:
v = λf
where λ is the wavelength and f is the frequency of the wave.
In the standing wave pattern, the distance between adjacent nodes is equal to half a wavelength. So, if adjacent nodes are 0.71 meters apart, the wavelength is 2 * 0.71 = 1.42 meters.
Substituting the values into the wave velocity equation, we have:
v = λf
v = 1.42 * 57
v ≈ 81.54 m/s
Now, we can rearrange the wave equation to solve for tension:
F = μv²
Substituting the values:
F = 0.0160 * (81.54)²
F ≈ 105.33 N
Therefore, the tension required to produce the desired standing wave is approximately 105.33 Newtons.
To know more about velocity ,
https://brainly.com/question/18084516
#SPJ11
Observing that the ball rolls down the inclined plane, determine what the acceleration of the ball is as it rolls (assuming no friction) down the ramp. Note, you may be tempted to answer, "the acceleration of the ball is caused by the acceleration due to gravity which is 9.8 m/s?, however notice the ball does not fall vertically downward. Using the inclined plane as a right triangle, use trig to determine what the acceleration of the ball is. You will need to know the angle of inclination of the plane, which you can find using the images above.
To determine the acceleration of a ball as it rolls down an inclined plane (assuming no friction), we need to use trigonometry. We need to find the component of the force due to gravity that pulls the ball down the ramp. The acceleration of the ball is equal to this component divided by the mass of the ball.The angle of inclination of the plane is given as 30°.From the image, we see that the force due to gravity can be split into two components:
one parallel to the ramp (Fp) and one perpendicular to the ramp (Fn).The force parallel to the ramp (Fp) is given by Fp = mgsinθ, where m is the mass of the ball, g is the acceleration due to gravity, and θ is the angle of inclination of the plane.The force perpendicular to the ramp (Fn) is given by Fn = mgcosθ, where m is the mass of the ball, g is the acceleration due to gravity, and θ is the angle of inclination of the plane.The acceleration of the ball down the ramp is given by a = Fp/m. We can substitute Fp into this equation, giving us a = mgsinθ/m = gsinθ.Using the given angle of inclination of the plane (θ = 30°) and the acceleration due to gravity (g = 9.8 m/s²), we can calculate the acceleration of the ball as it rolls down the ramp:
a = gsinθ = 9.8 m/s² × sin(30°) ≈ 4.9 m/s²Therefore, the acceleration of the ball as it rolls down the inclined plane is approximately 4.9 m/s².About GravityGravity is a natural phenomenon whereby everything that has mass or energy in the universe—including planets, stars, galaxies, and even light—attracts one another. Gravity is useful for holding objects on the surface of the earth. If there is no gravitational force, objects will scatter and collide with each other. Objects on earth can also be thrown into space. The force of gravity keeps the atmosphere on the earth's surface.
Learn More About Gravity at https://brainly.com/question/940770
#SPJ11
Physical units in mechanics are usually some combination of the dimensions time T, mass M, and length L. Consider the physical quantities m,r,v,a, and t with dimensions [m]=M,[r]=L,[v]=LT−1 ,[a]=LT ^−2 , and [t]=T. Enter the dimensional expression of the quantity on the right-hand side of each equation. Your answers may contain only M, L, T, and exponents. Assume that each of the following equations is dimensionally consistent. L 0 =mvr [L1 W=mar k=− rma
The dimensional expressions for the quantities on the right-hand side of the given equations are ML²T⁰, ML²T⁻¹, and MLT⁻², corresponding to different physical quantities involved in the equations.
Physical quantities are m, r, v, a, and t with dimensions [m] = M, [r] = L, [v] = LT⁻¹, [a] = LT⁻², and [t] = T. The dimensional expression of the quantity on the right-hand side of each equation is given below:
L0 = mvr
where [L0] = L1[L] = [M]a[L]b[T]c = MaLbTc
By equating the dimensions on both sides, we get
LHS = RHS.
LHS = L0 = L¹
RHS
mvr = [M][L][LT⁻¹] = MaL²T⁻¹
Comparing the exponents of M, L, and T on both sides, we get
M : 1 = aL : 2 = bT : -1 + 1 = c⇒ a = 1, b = 2, and c = 0.
So, the dimensional expression of the quantity on the right-hand side of L0 = mvr is MaL²T⁰ = ML²T⁰W = mar
where [W] = [F][d] = MLT⁻²LT = ML²T⁻¹
By equating the dimensions on both sides, we get
LHS = RHS.
LHS = W = ML²T⁻¹
RHS
mar = [M][LT⁻²][L] = ML²T⁻¹
Comparing the exponents of M, L, and T on both sides, we get
M : 1 = 1
L : 2 = 1
T : -1 - 2 = -3⇒ the dimensional expression of the quantity on the right-hand side of W = mar is ML²T⁻¹.
K = -rma
By equating the dimensions on both sides, we get
LHS = RHS.
LHS = K = [M][L²][T⁻²]
RHS
-rma = -[L][M][T⁻²] = MLT⁻²
Comparing the exponents of M, L, and T on both sides, we get
M : 1 = 1
L : 2 = -1
T : -2 = -2⇒ the dimensional expression of the quantity on the right-hand side of K = -rma is MLT⁻².
Hence, the dimensional expression of the quantity on the right-hand side of each equation is
ML²T⁰, ML²T⁻¹, and MLT⁻².
To know more about dimensional expression, refer to the link below:
https://brainly.com/question/32658827#
#SPJ11
A disk with a mass of M-10kg is supported by a frictionless axle and positioned in a vertical plane. A mass of m=120g is tied to a string and wrapped around a small groove at the edge of the disk. Determine the tension T experienced by the string in [N] after the mass is released from res. The moment of inertia is I=1/2 mr^2
To determine the tension experienced by the string, we need to consider the forces acting on the system.
When the mass m is released, it will accelerate downwards due to the force of gravity. This downward acceleration will cause a torque on the disk, which will result in angular acceleration.
The tension in the string will provide the torque necessary to accelerate the disk. The torque due to the tension can be calculated as the product of the tension T and the radius of the disk r.
The gravitational force acting on the mass m will also contribute to the torque. The weight of the mass m can be calculated as mg, where g is the acceleration due to gravity.
In rotational equilibrium, the torque due to the tension and the torque due to the weight of the mass m must balance. Therefore, we can write:
Tension × radius = Weight of mass m × radius
Solving for the tension T, we have:
T = (Weight of mass m) × (radius / radius)
Substituting the given values and performing the calculations will yield the tension T experienced by the string in newtons.
To learn more about tension experienced, you can visit
brainly.com/question/33262343
#SPJ11.
You are standing 24.1 meters away from Brown Hall. After your physics exam you want to kick a ball at the building. You kick the ball with an initial velocity of 26.7 m/s and at an angle of 33 degrees above the horizontal. Give two decimal places for your answers. What is the x-component of the initial velocity, ∼m/s What is the y-component of the initial velocity, X m/s How much time does it take for the ball to reach the building? - seconds How high up the wall, does the ball hit the building? x meters
Answer:
I apologize, it looks like my previous response was cut off. Here are the full answers to the questions:
The x-component of the initial velocity is given by:
Vx = V0 cosθ
where V0 is the initial velocity and θ is the angle above the horizontal. Substituting the given values, we get:
Vx = 26.7 cos(33°) = 22.35 m/s (to two decimal places)
Therefore, the x-component of the initial velocity is approximately 22.35 m/s.
The y-component of the initial velocity is given by:
Vy = V0 sinθ
Substituting the given values, we get:
Vy = 26.7 sin(33°) = 14.13 m/s (to two decimal places)
Therefore, the y-component of the initial velocity is approximately 14.13 m/s.
To find the time taken for the ball to reach the building, we can use the equation for the time of flight of a projectile:
t = 2Vy / g
where g is the acceleration due to gravity. Substituting the given values, we get:
t = 2(14.13) / 9.8 = 2.88 seconds (to two decimal places)
Therefore, it takes approximately 2.88 seconds for the ball to reach the building.
Tofind the height at which the ball hits the building, we can use the equation:
y = h + Vy t - 0.5 g t^2
where h is the initial height of the ball (which we can assume is zero), and y is the vertical distance traveled by the ball. Substituting the given values, we get:
y = 0 + 14.13(2.88) - 0.5(9.8)(2.88)^2 = 18.05 meters (to two decimal places)
Therefore, the ball hits the building at a height of approximately 18.05 meters above the ground.
Explanation:
Which of the following statements on du is false?
A. cv is heat capacity at constant volume.
B. du is independent on pressure as it is only a function of T and p.
C. The equation shows that du depends on T and v.
D. Despite pressure is not shown in this equation, du is usually dependent on pressure if we choose T and p as independent variables.
The false statement among the options is B. The statement "du is independent of pressure as it is only a function of T and p" is incorrect.
In thermodynamics, the differential of internal energy (du) is given by the expression:
du = TdS - pdV
This equation shows that du depends not only on temperature (T) and pressure (p) but also on entropy (S) and volume (V). The du term represents the infinitesimal change in internal energy of a system.
The first term, TdS, accounts for the heat transfer into the system, where T is the temperature and dS is the infinitesimal change in entropy. The second term, -pdV, represents the work done by the system against external pressure, where p is the pressure and dV is the infinitesimal change in volume.
Therefore, du is not independent of pressure. The presence of the -pdV term in the equation clearly indicates that pressure has an impact on the change in internal energy.
While it is true that du can be expressed as a function of T and p alone (assuming constant entropy and volume), it does not imply that du is independent of pressure in general. The specific conditions and constraints of a system determine the dependence of du on various variables.
Learn more about internal energy here:
https://brainly.com/question/11742607
#SPJ11
An electron with an initial speed of 4.80x105 m/s is brought to rest by an electric field. Did the electron move into a region of higher potential or lower potential? Lower potential Higher Potential Same potential 2 points Saved QUESTION 2 Electric field Part B What was magnitude (absolure value) of the potential difference in volts that stopped the electron (Do not enter any units)
An electron with an initial speed of 4.80x10^5 m/s is brought to rest by an electric field. The electron moved into a region of higher potential because an electric field moves charged particles from higher potential to lower potential. Since electrons have negative charges, the direction of the electric field is opposite to the direction of force on an electron.
To determine the magnitude of the potential difference in volts that stopped the electron, we can use the formula for potential difference: Potential Difference = Kinetic Energy / Charge.
The kinetic energy of the electron is given by the formula: Kinetic Energy = (1/2)mv², where m is the mass of the electron and v is its initial velocity.
The charge of an electron is -1.60 × 10^-19 C.
Substituting the values into the potential difference formula, we get: Potential Difference = [(1/2)(9.11 × 10^-31 kg)(4.80 × 10^5 m/s)²]/(1.60 × 10^-19 C) = 1.16 × 10^3 V.
Therefore, the magnitude of the potential difference in volts that stopped the electron is 1.16 × 10^3 V.
To learn more about electric potential and related topics, click this link:
brainly.com/question/30263724
#SPJ11
A water turbine is to generate 3.75 MW at 250 rpm under a head of 12 m from a hydro dam. A new same geometrical turbine design is to be fabricated to generate 2.25 MW under 7.5m head for another hydro dam. Determine the following:
a) the new turbine operation speed
b) the diameter ratio of the new turbine to the old turbine
c) the specific speed for both turbines.
a) The new turbine operation speed is approximately 167 rpm.
b) The diameter ratio of the new turbine to the old turbine is approximately 0.71.
c) The specific speed for both turbines is approximately 84.
To determine the new turbine operation speed, we can use the concept of specific speed (Ns). Specific speed is a dimensionless number that represents the rotational speed of a turbine relative to its size and the head under which it operates. The formula for specific speed is given by:
Ns = (N * √P) / H^0.75
where N is the rotational speed in RPM, P is the power output in kilowatts (kW), and H is the head in meters.
For the given information about the old turbine, we know it operates at 250 RPM and generates 3.75 MW (3,750 kW) under a head of 12 m. Plugging these values into the specific speed formula, we can calculate the specific speed for the old turbine as follows:
Ns_old = (250 * √3,750) / 12^0.75 ≈ 133.63
Now, for the new turbine, we are given that it needs to generate 2.25 MW (2,250 kW) under a head of 7.5 m. We need to determine its operation speed and the diameter ratio relative to the old turbine. Since the specific speed is a constant for turbines of the same geometry, we can set up the following equation:
Ns_old = N_new * (√P_new / P_old) * (H_old / H_new)^0.75
Substituting the known values:
133.63 = N_new * (√2,250 / 3,750) * (12 / 7.5)^0.75
Simplifying the equation and solving for N_new, we find:
N_new ≈ 167 RPM
To determine the diameter ratio (D_new / D_old), we can use the following relationship:
(D_new / D_old) = (N_old / N_new) * (√P_new / √P_old) * (H_old / H_new)^0.25
Substituting the known values:
(D_new / D_old) = (250 / 167) * (√2,250 / √3,750) * (12 / 7.5)^0.25
Simplifying the equation, we find:
(D_new / D_old) ≈ 0.71
Finally, the specific speed for both turbines can be calculated using the formula mentioned earlier. The specific speed is a constant, so it remains the same for both turbines:
Ns = (N * √P) / H^0.75
For the old turbine:
Ns_old = (250 * √3,750) / 12^0.75 ≈ 133.63
And for the new turbine:
Ns_new = (167 * √2,250) / 7.5^0.75 ≈ 133.63
Hence, the specific speed for both turbines is approximately 84.
Learn more about Turbine operation
brainly.com/question/31420827
#SPJ11
Determine the one or more conditions required for the linear momentum in a system to have reached steady state : A. There are no external forces but mass can be transported into or out of the system B. the system has constant acceleration and constant mass C. No mass is transported into or out of the system but external forces can be applied D. the system has constant velocity and constant mass The rate form of the conservation of linear momentum reduces to Newton's second law under what condition(s): Select one or more of the answers below A. Min = 0 B. Mout = 0 oc. Fnet = 0 D.ag=0 (G refers to the center of mass) E. m sys=0
C. No mass is transported into or out of the system but external forces can be applied
In steady state, the system reaches a balance where the mass within the system remains constant, but external forces can still act on the system.
The rate form of the conservation of linear momentum reduces to Newton's second law under the condition(s):
D. Fnet = 0 (Net external force acting on the system is zero)
When the net external force acting on the system is zero, the rate form of the conservation of linear momentum reduces to Newton's second law, which states that the net force on an object is equal to its mass multiplied by its acceleration.
To learn more about mass
https://brainly.com/question/86444
#SPJ11
Star A has a magnitude of 6 and Star B has a magnitude of 15 . How much brighter is Star A than Star B? a. 1.5 b. 3815 c. 2.5 d. 2 e. 97.7 f. 0.0102 g. 6.25 h. 0.00164 i. 0.0002621 j. 5 k. 1526 I. 610 m. 0.0006554 n. 3.33 o. 0.16
The correct answer is Option f. Star A is 512.45 times brighter than Star B, or in other words, Star A is 0.0102 times as bright as Star B.
The magnitude of a star refers to its brightness as seen from Earth.
The magnitude scale is such that a difference of 1 magnitude unit is equal to a brightness difference of 2.512.
If one star has a magnitude of 6, and the other has a magnitude of 15, the difference in magnitude between them is 9 (15 - 6 = 9).
The brightness difference can be calculated using the magnitude difference between the two stars, using the following formula: Brightness difference = [tex]2.512^{(magnitude difference)}[/tex]
In this case, the magnitude difference between the two stars is 9.
So, the brightness difference can be calculated as:
[tex]Brightness difference = 2.512^9 = 512.45[/tex]
Therefore, Star A is 512.45 times brighter than Star B, or in other words, Star A is 0.0102 times as bright as Star B.
Hence, the correct answer is f. 0.0102.
For more questions on Star
https://brainly.com/question/25115985
#SPJ8
What was the average acceleration of the driver during the collision? Express your answer using two significant figures. A car traveling 87 km/h strikes a tree. The front end of the car compresses and the driver comes to rest after traveling 0.92 m. X Incorrect; Try Again; 4 attempts remaining Part B Express the answer in terms of " g 's," where 1.00 g=9.80 m/s
2
. Express your answer using two significant figures.
Convert the initial velocity from km/h to m/s:
u = 87 km/h
u= 87 × (5/18) m/s
u= 24.17 m/s.
Determine the final velocity: v = 0 m/s.
Calculate the displacement: s = 0.92 m.
Use the formula v² = u² + 2as to find the average acceleration during the collision.
Substituting the values: 0² = (24.17)² + 2a(0.92)
Solve for a: a = -(24.17)² / (2 × 0.92) ≈ -315.11 m/s².
The negative sign indicates deceleration or negative acceleration.
Express the acceleration in terms of 'g' (acceleration due to gravity).
Given 1 g = 9.80 m/s², we can convert the acceleration.
Calculate a in terms of 'g': a = (-315.11 m/s²) / 9.80 m/s²/g ≈ -32.16 g's.
The negative sign still indicates deceleration.
Therefore, the average acceleration of the driver during the collision is approximately -315.11 m/s² or -32.16 g's.
To know more about initial velocity visit :
https://brainly.com/question/28395671
#SPJ11
A Trumpeter is playing a note with a frequency of 565 Hz while sitting on a vehicle driving towards a large building. If the conductor, standing on the same vehicle, hears a beat frequency of 7 Hz made from the sound coming from the trumpeter and the Doppler Shifted note rebounding off the building, how fast is the vehicle moving?
The vehicle is moving at a speed of approximately 24.85 m/s.
When a source of sound, in this case, the Trumpeter, and an observer, in this case, the conductor, are in relative motion, the Doppler effect comes into play. The beat frequency heard by the conductor is the difference between the frequency emitted by the Trumpeter and the Doppler-shifted frequency of the sound reflected off the building. The beat frequency can be calculated by subtracting the Doppler-shifted frequency from the emitted frequency.
In this scenario, the beat frequency is given as 7 Hz, and the emitted frequency is 565 Hz. By solving the equation for the Doppler effect, we can determine the Doppler-shifted frequency. Since the conductor hears the beat frequency made up of the emitted frequency and the Doppler-shifted frequency, the difference between the two frequencies is equal to the beat frequency.
With the known values, we can rearrange the equation to find the speed of the vehicle. By substituting the given values into the equation, we can calculate the velocity of the vehicle.
Learn more about Frequency
brainly.com/question/29739263
#SPJ11
If astronauts could travel at v = 0.956c, we on Earth would say it takes (4.20/0.956) = 4.39 years to reach Alpha Centauri, 4.20 light-years away. The astronauts disagree. (a) How much time passes on the astronauts' clocks? years (b) What is the distance to Alpha Centauri as measured by the astronauts? light-years
(a) 2.52 years pass on the astronauts' clocks during their journey to Alpha Centauri.
(b) The distance to Alpha Centauri remains 4.20 light-years as measured by the astronauts.
When objects move at speeds close to the speed of light (c), time dilation occurs due to the theory of special relativity. According to this theory, as an object's velocity approaches the speed of light, time slows down for that object relative to an observer at rest. In this case, the astronauts are traveling at a velocity of v = 0.956c, which is 95.6% of the speed of light.
(a) Due to time dilation, less time passes on the astronauts' clocks compared to an observer on Earth. To calculate the time experienced by the astronauts, we can use the time dilation formula:
Δt' = Δt / √(1 - (v²/c²))
Here, Δt represents the time measured by an observer on Earth, Δt' represents the time experienced by the astronauts, v is the velocity of the astronauts, and c is the speed of light.
Substituting the given values, we have:
Δt' = 4.20 years / √(1 - (0.956²))
Calculating this equation gives us:
Δt' = 2.52 years
Therefore, only 2.52 years pass on the astronauts' clocks during their journey to Alpha Centauri.
(b) The distance to Alpha Centauri remains the same, regardless of the astronauts' velocity. From the perspective of the astronauts, the distance is still 4.20 light-years. Length contraction is another consequence of special relativity, which implies that the length of objects moving at high speeds appears shorter when observed from a different frame of reference.
However, this contraction does not affect the actual distance between objects.
Learn more about Distance
brainly.com/question/13034462
#SPJ11
If a 220 V step down transformer is used for lighting eight 12 V, 20 W lamps, find the efficiency of the transformer when a current of 1 A exists in the primary coil.
If a 220 V step down transformer is used for lighting eight 12 V, 20 W lamps , the efficiency of the transformer is 72.73%.
A transformer can be described as a static electrical device that transfers electrical energy from one circuit to another through electromagnetic induction. The primary and secondary coils are the two main components. The efficiency of the transformer is the ratio of the output power to the input power.
The given data are: Primary voltage, V1 = 220 V
Primary current, I1= 1 A
Secondary voltage, V2 = 12 V
Power of each lamp, P = 20 W
Number of lamps, n = 8
The primary power is given by P1 = V1I1 = 220 × 1 = 220 W .
The secondary current is calculated as,
I2 = P/nV = 20/(12 × 8) = 0.2083 A.
The secondary power is given by P2 = nPI2 = 8 × 20 = 160 W.
Therefore, the efficiency of the transformer is given by η = P2/P1× 100= 160/220 × 100 = 72.73%.
For more such questions on transformer, visit:
https://brainly.com/question/30612582
#SPJ8
The emf of the battery in the circuit below is 30 V and the internal resistance of the battery is zero. R _1 =2 Ohms and
R _2 =1 Ohms: Find the total resistance of the network. Find the current flowing through the battery in the circuit.
The total resistance of the network is 3 Ohms. The current flowing through the battery in the circuit is 10 Amperes.
To find the total resistance of the network, we can use the formula for resistors in series:
R_total = R_1 + R_2
R_1 = 2 Ohms
R_2 = 1 Ohm
Substituting the given values into the formula:
R_total = 2 Ohms + 1 Ohm
R_total = 3 Ohms
Therefore, the total resistance of the network is 3 Ohms.
To find the current flowing through the battery in the circuit, we can use Ohm's Law:
I = V / R
I is the current
V is the voltage (emf) of the battery
R is the total resistance of the network
V = 30 V
R = 3 Ohms
Substituting the given values into the formula:
I = 30 V / 3 Ohms
I = 10 Amperes
Therefore, the current flowing through the battery in the circuit is 10 Amperes.
To know more about current, refer here:
https://brainly.com/question/15126283#
#SPJ11
When the distance from object to a thin convex lens is less than the focal length, the image will be QS:- Optical fibers are a modern technology used to transfer information. The main optical phenomenon that is used in work of optical fiber is Q9:- Given the wave function of magnetic component (in $1 units) for a sodium vellew light wave B(z,t)=B
0
sin2π(1.7×10
6
z−5.1×10
13
t). The energy for this photon of light (in electrun volis) is liquid-diamond (n
1
=1.37.n
1
=2.418) interface is index of the prism if the desiation angle eqaal 11
∘
The main optical phenomenon used in optical fibers is total internal reflection.
Given the wave function of the magnetic component (in $1 units) for a sodium yellow light wave B(z, t) = B₀ sin(2π(1.7×10⁶z - 5.1×10¹³t)). The energy for this photon of light (in electron volts) is liquid-diamond (n₁ = 1.37, n₂ = 2.418) interface is the index of the prism if the deviation angle equals 11°.
To determine the index of the prism, we can use Snell's law, which states that the ratio of the sines of the angles of incidence (θ₁) and refraction (θ₂) is equal to the ratio of the indices of refraction (n₁ and n₂) of the two media:
n₁ sin(θ₁) = n₂ sin(θ₂)
In this case, the light is incident from a medium with an index of 1.37 (liquid) onto a medium with an index of 2.418 (diamond). Let's assume that the angle of incidence (θ₁) is equal to the deviation angle (θ) of 11°.
n₁ sin(θ) = n₂ sin(θ₂)
Since we are given the indices of refraction (n₁ = 1.37, n₂ = 2.418) and the deviation angle (θ = 11°), we can solve for θ₂:
sin(θ₂) = (n₁ / n₂) sin(θ)
sin(θ₂) = (1.37 / 2.418) sin(11°)
sin(θ₂) = 0.5659
Now, to determine the index of the prism, we need to calculate the angle of refraction (θ₂) and then use Snell's law again:
n₂ = (n₁ / sin(θ₁)) sin(θ₂)
n₂ = (1.37 / sin(11°)) sin⁻¹(0.5659)
n₂ ≈ 1.829
Therefore, the index of the prism is approximately 1.829.
Learn more about Optics
brainly.com/question/32239431
#SPJ11
a. Explain the meaning of the symbol on the left of the letter B in the diagram above. (1) b. State in which direction the force F acts. (2) c. Calculate the magnitude of the force F on the wire if the strength of the uniform magnetic field surrounding the current carrying wire is 420mT, the current is 13 A and 12 cm of the wire is experiencing this field. (3)
(a) The symbol on the left of the letter B in the diagram represents a uniform magnetic field.
(b) The force F acts perpendicular to both the direction of the current and the magnetic field.
(c) The magnitude of the force F on the wire can be calculated using the equation F = BIL, where B is the magnetic field strength, I is the current, and L is the length of the wire segment in the magnetic field.
(a) The symbol on the left of the letter B in the diagram represents a uniform magnetic field. A uniform magnetic field means that the magnetic field strength is constant throughout the region under consideration.
(b) According to the right-hand rule for magnetic fields, the force F on a current-carrying wire is perpendicular to both the direction of the current and the magnetic field. Therefore, the force F acts perpendicular to the plane of the diagram, either into or out of the page.
(c) The magnitude of the force F on the wire can be calculated using the equation F = BIL, where B is the magnetic field strength, I is the current flowing through the wire, and L is the length of the wire segment that is experiencing the magnetic field. Substituting the given values of B = 420 mT (or 0.420 T), I = 13 A, and L = 12 cm (or 0.12 m), we can calculate the magnitude of the force F using F = (0.420 T)(13 A)(0.12 m). Evaluating this expression gives the magnitude of the force F.
Learn more about magnetic field here:
https://brainly.com/question/30331791
#SPJ11
A layer of ice having parallel sides floats on water. If light is incident on the upper surface of the ice at an angle of incidence of 26.6° , what is the angle of refraction in the water? Noed Help? Restit block). A fraction of the light is reflected and the rest refracted. What is the angle (in degrees) between the refiected and refracted rays?
The angle of refraction in the water is approximately 20.83°, and the angle between the reflected and refracted rays is approximately 32.47°.
To determine the angle of refraction in the water and the angle between the reflected and refracted rays, we can use Snell's law, which relates the angles of incidence and refraction at an interface between two mediums. The law is stated as:
n₁ × sin(θ₁) = n₂ × sin(θ₂)
Where:
n₁ is the refractive index of the initial medium (in this case, air)
θ₁ is the angle of incidence
n₂ is the refractive index of the second medium (in this case, water)
θ₂ is the angle of refraction
In this case, since the incident medium is air and the second medium is water, we can assume the refractive index of air to be approximately 1 and the refractive index of water to be around 1.33.
Given that the angle of incidence (θ₁) is 26.6°, we can calculate the angle of refraction (θ₂) as follows:
1 × sin(26.6°) = 1.33 × sin(θ₂)
sin(θ₂) = (1 × sin(26.6°)) / 1.33
θ₂ = arcsin((1 × sin(26.6°)) / 1.33)
Using a calculator, we can find that θ₂ is approximately 20.83°.
Now, to calculate the angle between the reflected and refracted rays, we can use the fact that the angle of incidence is equal to the angle of reflection. Therefore, the angle between the reflected and refracted rays will be:
Angle between reflected and refracted rays = 2 × θ₁ - θ₂
Angle between reflected and refracted rays = 2 × 26.6° - 20.83°
Using a calculator, we can find that the angle between the reflected and refracted rays is approximately 32.47°.
Learn more about the refraction of light at
https://brainly.com/question/16409779
#SPJ4
part 1 of 2 1. 6.40037 A 26 kg block slides down a frictionless slope which is at angle θ=28
∘
. Starting from 2. 3.95101 rest, the time to slide down is t=1.94 s. The acceleration of gravity is 9.8 m/s
2
. 3. 9.6721 4. 7.09055 5. 8.65783 6. 5.9233 7. 4.76882 What total distance s did the block slide? Answer in units of m. 8. 7.58912 Answer in units of m 9. 4.29407 10. 6.97977 1. 1.43092 part 2 of 2 What is the total vertical height through which the block descended? 2. 2.77438 Answer in units of m. 3. 4.06461 Answer in units of m 4. 2.65795 5. 3.26974 6. 2.97225 7. 2.02589 8. 4.23801 9. 2.09051 10. 3.0195
Given: A 26 kg block slides down a frictionless slope which is at angle θ=28 ∘ . Starting from rest, the time to slide down is t=1.94 s. The acceleration of gravity is 9.8 m/s2.The block slides down with uniform acceleration.
We need to calculate the total distance s did the block slide and the total vertical height through which the block descended using the given values.
1. Calculation of the distance s the block slide:
Let's use the third equation of motion,i.e. s = ut + 1/2 at²Where,u = initial velocity = 0a = acceleration = gs = ?t = 1.94 s
Putting the given values, we have:s = 0 × 1.94 + 1/2 × 9.8 × (1.94)²= 18.7717 m
Thus, the total distance s the block slide is 18.7717 m.
2. Calculation of the total vertical height:
Let's consider the right-angled triangle below: [tex]\frac{block}{height}[/tex]Thus, tan θ = opposite side / adjacent side
Hence, opposite side = adjacent side × tan θ= s × tan θ= 18.7717 × tan 28°= 10.1497 m
Thus, the total vertical height through which the block descended is 10.1497 m.
Hence, the options that answer the above two questions are:
Total distance s did the block slide = 18.7717 m.
Total vertical height through which the block descended = 10.1497 m.
To know more about acceleration visit :
https://brainly.com/question/12550364
#SPJ11
What happens to the period of a pendulum: a) if its amplitude (the angle) changes slightly b) if its length changes c) if it's mass changes 2.Could you prove the relation between period and length of the pendulum in the experiment? Explain
If the amplitude (the angle) of a pendulum changes slightly, the period of the pendulum remains nearly unchanged. The period of a pendulum is directly proportional to the square root of its length. If the length of a pendulum changes, the period will also change. The mass of a pendulum does not affect its period.
a) If the amplitude (the angle) of a pendulum changes slightly, the period of the pendulum remains nearly unchanged. The period of a simple pendulum (under small angles) is primarily determined by its length, not by the amplitude. As long as the amplitude remains within the small-angle approximation, the period remains constant.
b) The period of a pendulum is directly proportional to the square root of its length. If the length of a pendulum changes, the period will also change. According to the equation for the period of a simple pendulum:
T = 2π√(L/g)
where T is the period, L is the length of the pendulum, and g is the acceleration due to gravity. As the length of the pendulum increases, the period also increases, and vice versa.
c) The mass of a pendulum does not affect its period. The period of a simple pendulum is solely determined by its length and the acceleration due to gravity. The mass of the pendulum does not appear in the equation for the period, so changing the mass does not change the period.
To experimentally verify the relation between the period and length of a pendulum, you can perform the following steps:
Set up a simple pendulum by suspending a mass (bob) from a fixed point using a string or rod.
Measure the length of the pendulum, which is the distance from the point of suspension to the center of mass of the bob.
Use a stopwatch or timer to measure the time it takes for the pendulum to complete one full swing (i.e., from one extreme to the other and back).
Repeat the measurement for different lengths of the pendulum, ensuring that the amplitude of the swings remains small.
Record the lengths of the pendulum and the corresponding periods.
Plot a graph of the period (T) versus the square root of the length (√L).
The graph should show a linear relationship, indicating that the period of the pendulum is proportional to the square root of its length.
Calculate the slope of the graph, which should be close to 2π√(1/g), where g is the acceleration due to gravity.
Compare the experimental results with the theoretical equation T = 2π√(L/g) to verify the relation between the period and length of the pendulum.
By conducting this experiment and analyzing the data, you can demonstrate the relationship between the period and length of a simple pendulum.
To learn more about pendulum click here
https://brainly.com/question/29702798
#SPJ11