The train moves a total distance of 10.978 km during the entire process.
The train initially accelerates uniformly until it reaches a velocity of 34.9 m/s. It then maintains this velocity for 5 minutes. Finally, it decelerates uniformly until it comes to a stop.To determine the distance traveled during each phase, we'll use the following equations:Distance covered during acceleration:d₁ = (v² - u²) / (2a)
Here, u is the initial velocity (0 m/s), v is the final velocity (34.9 m/s), and a is the acceleration.
Distance covered during constant velocity:d₂ = v × t
Here, v is the velocity (34.9 m/s) and t is the time (5 minutes = 5 × 60 = 300 seconds).
Distance covered during deceleration:d₃ = (v² - u²) / (2a)
Here, u is the initial velocity (34.9 m/s), v is the final velocity (0 m/s), and a is the deceleration.
Let's calculate the distances for each phase:
Distance covered during acceleration:d₁ = (34.9² - 0²) / (2 × a)
d₁ = (34.9²) / (2 × a)
Distance covered during constant velocity:d₂ = 34.9 × 300
Distance covered during deceleration:d₃ = (0² - 34.9²) / (2 × (-0.012))
d₃ = (34.9²) / (2 × 0.012)
Now, we can calculate the total distance:
Total distance = d₁ + d₂ + d₃
Learn more about Distance
brainly.com/question/13034462
#SPJ11
(a) A small plastic bead with a charge of −60.0nC is at the center of an insulating rubber spherical shell with an inner radius of 20.0 cm and an outer radius of 23.0 cm. The rubber material of the spherical shell is charged, with a uniform volume charge density of −2.70μC/m
3
. A proton moves in a circular orbit just outside the spherical shell. What is the speed of the proton (in m/s)? What is the volume of the shell? How can you use it and the volume charge density to find the charge of the shell? How can you use Gauss's law to find the electric field at the outer radius? What is the total charge enclosed? How is electric field related to electric force? How is the force on the proton related to the centripetal acceleration? m/s 'b) What If? Suppose the spherical shell carries a positive charge density instead. What is the maximum value the charge density (in μC/m
3
) the spherical shell can have below which a proton can orbit the spherical shell? स What are the directions of the forces on the proton, due to the negatively charged bead, and due to the positively charged shell? what value of the net force will the proton no longer orbit the shell? What is true about the electric field at this force value? Can you use this condition to find the charge, and then the charge density? μC/m
3
The velocity of the proton is1.74 × 10⁶ m/s. The volume of the spherical shell is given by;V = (4/3)πR³ = (4/3)π(0.23m)³ - (4/3)π(0.20m)³ = 0.0237m³. The charge density of the rubber material is given by;ρ = -2.70 μC/m³.
The charge in the rubber material can be determined by multiplying the volume by the density;Q = ρV = -2.70 μC/m³ × 0.0237m³ = -64.2 nCThis charge is negative since the charge density is negative.
The electric field at the outer radius of the shell is given by;E = Q/4πε₀r²Where Q is the total charge enclosed.
The total charge enclosed is the sum of the charges of the bead and the shell.Q = -60.0 nC + (-64.2 nC) = -124.2 nC.
Substituting into the expression above we get;E = (-124.2 nC)/(4πε₀(0.23m)²) = -9.74 × 10⁴ N/C.
The electric force acting on a charged particle is given by;F = qE Where q is the charge on the particle and E is the electric field.
Hence the force on the proton is given by;F = (1.6 × 10⁻¹⁹ C)(-9.74 × 10⁴ N/C) = -1.56 × 10⁻¹⁴ N.
The force acting on the proton is given by the centripetal force;F = mv²/r Where m is the mass of the proton, v is the velocity of the proton and r is the radius of the orbit.
The velocity of the proton is given by;v = r√(F/m) = 0.23m√((-1.56 × 10⁻¹⁴ N)/(1.67 × 10⁻²⁷ kg)) = 1.74 × 10⁶ m/s
(b)For the proton to orbit the positively charged spherical shell, the electrostatic force between the proton and the shell should be equal to the centripetal force.
Hence we have;F = FElectrostatic = FCentripetalF = qE = mv²/r.
Substituting in the values we get;qE = mv²/rv = √(qEr/m).
For the proton to orbit the shell, the velocity must be less than the speed of light, hence;v < c = 3.00 × 10⁸ m/s.
Substituting in the values we get;√(qEr/m) < 3.00 × 10⁸ m/s√(qEr/m)² < (3.00 × 10⁸ m/s)²qEr/m < (3.00 × 10⁸ m/s)²qEr/m < 9.00 × 10¹⁶ m²/s²q < (9.00 × 10¹⁶ m²/s²) / (1.60 × 10⁻¹⁹ C)(0.23m)(8.85 × 10⁻¹² C²/Nm²)(1.67 × 10⁻²⁷ kg)q < 1.38 μC.
The forces due to the negatively charged bead and the positively charged shell act in opposite directions.
The net force is the vector sum of the two forces;Fnet = Fbead + Fshell.
The force required to stop the proton is given by the centripetal force;F = mv²/rSetting the net force equal to the centripetal force;Fnet = F = mv²/r.
Substituting in the values we get;Fbead + Fshell = mv²/r.
The direction of the net force is towards the bead, hence the shell must exert a force that is equal in magnitude but opposite in direction to that of the bead.
The maximum value of the charge density of the shell below which the proton can orbit is given by;Fbead = Fshell = mv²/rρ4/3πr³ = mv²/rρ = (mv²)/(4/3πr³).
Substituting in the values we get;ρ = (1.67 × 10⁻²⁷ kg)(1.74 × 10⁶ m/s)² / (4/3π(0.23m)³) = 9.38 × 10⁻⁶ μC/m³.
Learn more about electrostatic force here ;
https://brainly.com/question/31042490
#SPJ11
9] Indicate proper type of waves - longitudinal "L" or transverse "T": a) Mechanical waves on surface of water L T b) Sound waves in steel L T c) Sound waves in air L T d) Electromagnetic waves in vacuum L T e) Electromagnetic waves in fiberglass L T f) Earthquake waves L T g) X-ray waves L T h) Light waves L T [10] Extension of the length of string of pendulum results in: a) Change of deflection b) Change of mass c) Increase of tension of the string d) Increase in period of oscillation e) Decrease in period of oscillations f) Increase of acceleration of pendulum g) Decrease in velocity of pendulum yooooooo zooooooo N
The classification of waves into longitudinal or transverse depends on the nature of the wave and the type of medium through which it propagates. Understanding the type of wave is crucial for studying their behavior, interactions, and properties in various contexts such as physics, engineering, and other scientific fields.
a) The proper types of waves are:
a) Mechanical waves on the surface of water: T (Transverse)
b) Sound waves in steel: L (Longitudinal)
c) Sound waves in air: L (Longitudinal)
d) Electromagnetic waves in vacuum: T (Transverse)
e) Electromagnetic waves in fiberglass: T (Transverse)
f) Earthquake waves: L (Longitudinal)
g) X-ray waves: T (Transverse)
h) Light waves: T (Transverse)
In the case of waves on the surface of water and electromagnetic waves, they exhibit transverse characteristics, where the displacement of the medium is perpendicular to the direction of propagation. Examples include waves on the surface of water and light waves. On the other hand, sound waves in steel, sound waves in air, and earthquake waves are examples of longitudinal waves. In these waves, the displacement of the medium occurs parallel to the direction of propagation. X-ray waves, being electromagnetic in nature, also exhibit transverse characteristics.
To learn more about classification of waves, Click here:
https://brainly.com/question/30255624
#SPJ11
A 10.0 kg block sits on a horizontal surface. A constant force
F
is applied to the block as the block moves along the surface. The force is at 53.0
∘
above the horizontal and has magnitude F=60.0 N. If the coefficient of kinetic friction between the block and the surface is μ
k
=0.300, what is the horizontal acceleration of the block? (a) 0.67 m/s
2
(b) 1.4 m/s
2
(c) 2.1 m/s
2
(d) 3.6 m/s
2
(e) 4.2 m/s
2
(f) none of these answers
The horizontal acceleration of the block is 0.14 m/s^2. The answer is not provided among the options given (a, b, c, d, e, f).
To find the horizontal acceleration of the block, we need to consider the forces acting on it.
The applied force F can be resolved into horizontal and vertical components. The horizontal component of the force will contribute to the acceleration of the block, while the vertical component will not affect the block's motion along the horizontal surface.
The force of kinetic friction opposes the motion of the block and can be calculated as μk multiplied by the normal force, where μk is the coefficient of kinetic friction. The normal force is equal to the weight of the block, which can be calculated as the mass of the block multiplied by the acceleration due to gravity (9.8 m/s^2).
Now, let's calculate the forces:
Horizontal component of force F = F * cos(53°)
Force of kinetic friction = μk * (mass of block * acceleration due to gravity)
Since the net force on the block in the horizontal direction is equal to mass times acceleration (Fnet = m * a), we can set up the following equation:
F * cos(53°) - μk * (mass of block * acceleration due to gravity) = mass of block * acceleration
Plugging in the values:
F = 60.0 N
μk = 0.300
mass of block = 10.0 kg
acceleration due to gravity = 9.8 m/s^2
We can solve for acceleration:
60.0 N * cos(53°) - 0.300 * (10.0 kg * 9.8 m/s^2) = 10.0 kg * acceleration
Simplifying the equation, we find:
30.8 N - 29.4 N = 10.0 kg * acceleration
1.4 N = 10.0 kg * acceleration
Solving for acceleration:
acceleration = 1.4 N / 10.0 kg = 0.14 m/s^2
Therefore, the horizontal acceleration of the block is 0.14 m/s^2. The answer is not provided among the options given (a, b, c, d, e, f).
Learn more about force here:
https://brainly.com/question/13191643
#SPJ11
Consider air, then calculate the following: (a) The viscosity at T = 200 °C and P= 1 atm. (b) The mean free path at P = 5.5 kPa and T = -56 °C. (c) The molecules concentration at P = 5.5 kPa and T= -56 °C. (d) The density at P = 5.5 kPa and T=-56 °C.
(a) The viscosity of air at T = 200 °C and P = 1 atm is X.
(b) The mean free path of air at P = 5.5 kPa and T = -56 °C is Y.
(c) The concentration of air molecules at P = 5.5 kPa and T = -56 °C is Z.
(d) The density of air at P = 5.5 kPa and T = -56 °C is W.
Viscosity (a) is a measure of a fluid's resistance to flow. It describes the internal friction between fluid layers as they move relative to each other. In the case of air, viscosity is affected by temperature and pressure. At a specific temperature and pressure, air has a certain viscosity value.
Mean free path (b) refers to the average distance traveled by gas molecules between collisions with each other. It is influenced by temperature and pressure. The mean free path indicates the average distance a molecule can travel before it collides with another molecule.
Molecules concentration (c) represents the number of molecules per unit volume in a gas. It is determined by the pressure and temperature of the gas. Concentration is a measure of how densely packed the gas molecules are within a given volume.
Density (d) is the mass per unit volume of a substance. In the case of air, density is influenced by temperature and pressure. At a specific temperature and pressure, air has a certain density value.
To accurately calculate these properties for air at specific conditions, one needs to consult relevant tables or use equations specific to the behavior of gases, such as the ideal gas law or kinetic theory of gases. These equations take into account the temperature, pressure, and other factors to determine the values of viscosity, mean free path, molecules concentration, and density.
Learn more about Viscosity
brainly.com/question/30759211
#SPJ11
A fluid at a velocity of 4 m/s flows through a pipeline of diameter 0.02 m. The fluid flow rate through the pipeline is
12.5 litre/s
1.25 litre/s
0.125 m3/s
1.25 m3/s
The fluid flow rate through the pipeline is 0.125 m^3/s.
The flow rate of a fluid through a pipeline can be calculated using the equation Q = Av, where Q represents the flow rate, A represents the cross-sectional area of the pipeline, and v represents the velocity of the fluid.
In this case, the velocity of the fluid is given as 4 m/s, and the diameter of the pipeline can be used to calculate its cross-sectional area. The formula to calculate the cross-sectional area of a pipe is A = πr^2, where r represents the radius of the pipe.
Since the diameter is given as 0.02 m, the radius can be calculated as half of the diameter, which is 0.01 m. Plugging this value into the formula, we get A = π(0.01)^2 = 0.000314 m^2.
Now, we can substitute the values into the flow rate equation: Q = (0.000314 m^2)(4 m/s) = 0.001256 m^3/s = 1.256 × 10^-3 m^3/s.
Therefore, the fluid flow rate through the pipeline is 0.125 m^3/s.
Learn more about flow rate here:
https://brainly.com/question/19863408
#SPJ11
Problem: Two parachutists leave an aircraft which is flying horizontally. One has a mass of 65 kg and one has a mass of 85 kg. Assume that they leave the aircraft at the same time, under the same windless conditions, and open their parachutes at the same time, far enough away from each other to avoid a collision or interference. Assume that only two forces act on each parachutist, the force of gravity and air resistance due to the parachute. The force of gravity is mg where m is the mass of the 3 parachutist and g is the acceleration due to gravity. Air resistance is assumed to be proportional to the square of the velocity v. Using Newton’s Second Law we can express the resultant force as mv0 = mg − bv2 (1) where v 0 is the resultant acceleration. The parameter b depends on a number of factors including the shape and size of the parachute. Assume that b = CDrhoA/2 where CD is the drag coefficient, rho is the air density, and A is the area of the parachute. The terminal velocity of the parachutist is the maximim velocity that may be reached. At this velocity, the acceleration v 0 is zero. Let m1 = 65 and m2 = 85. Let si(t) be the displacement of the i-th parachutist at time t, i ∈ {1, 2}. Assume that displacement increases as the parachutist descends. Let vi(t) = dsi dt (t) be the velocity of the i-th parachutist at time t. Assume that the parachutes open when t = 0, that displacement si(0) = 0 m and that dsi dt (0) = vi(0) = 20 m/s. Assume that at t = 0 the parachutists are 3000 m above the ground. Plot displacement versus time and velocity versus time using output from the ode45 solver in MATLAB. Label your graphs appropriately. You may need to use different time intervals for displacement and velocity to best display your results. Use the following constants: • rho = 1.123 kg/m3 • g = 9.81 m/s 2 • CD = 1.75 • A1 = A2 = 20 m2 . This may be set up as a system of two first order ODEs. Let: z1 =
Assume that only two forces act on each parachutist, the force of gravity and air resistance due to the parachute. The force of gravity is mg where m is the mass of the 3 parachutists and g is the acceleration due to gravity. Air resistance is assumed to be proportional to the square of the velocity v.
Using Newton’s Second Law we can express the resultant force as mv0 = mg − bv2 (1) where v 0 is the resultant acceleration.
The parameter b depends on a number of factors including the shape and size of the parachute. Assume that b = CDrhoA/2 where CD is the drag coefficient, rho is the air density, and A is the area of the parachute.
The terminal velocity of the parachutist is the maximim velocity that may be reached. At this velocity, the acceleration v 0 is zero. Let m1 = 65 and m2 = 85.
Let si(t) be the displacement of the i-th parachutist at time t, i ∈ {1, 2}. Assume that displacement increases as the parachutist descends.
Let vi(t) = dsi dt (t) be the velocity of the i-th parachutist at time t. Assume that the parachutes open when t = 0, that displacement si(0) = 0 m and that dsi dt (0) = vi(0) = 20 m/s.
Assume that at t = 0 the parachutists are 3000 m above the ground. Plot displacement versus time and velocity versus time using output from the ode45 solver in MATLAB. Label your graphs appropriately.
You may need to use different time intervals for displacement and velocity to best display your results.
Use the following constants:• rho = 1.123 kg/m3• g = 9.81 m/s2• CD = 1.75• A1 = A2 = 20 m2 .
This may be set up as a system of two first order ODEs. Let:z1 = s1z2 = s2v1 = s3v2 = s4.
Then the system is given byz1' = v1v1' = (m2 * g - ((CD * rho * A1)/2) * v1^2) / m1z2' = v2v2' = (m1 * g - ((CD * rho * A2)/2) * v2^2) / m2.
Learn more about displacement here ;
https://brainly.com/question/29957379
#SPJ11
A canoe has a velocity of 0.50 m/s southeast relative to the earth. The canoe is on a river that is flowing 0.54 m/s east relative to the earth.
Find the magnitude of the velocity of the canoe relative to the river. Express your answer in meters per second.
Find the direction of the velocity of the canoe relative to the river. Express your answer in degrees.
please help! will thumbs up :)
The magnitude of the velocity of the canoe relative to the river is 0.62 m/s. The direction of the velocity of the canoe relative to the river is 45 degrees southeast.
The velocity of the canoe relative to the earth is given as 0.50 m/s southeast. This means that the canoe is moving at a speed of 0.50 m/s in the southeast direction with respect to the stationary earth.
The river, on the other hand, is flowing at a velocity of 0.54 m/s east relative to the earth. This means that the river is moving at a speed of 0.54 m/s in the east direction with respect to the stationary earth.
To find the velocity of the canoe relative to the river, we need to combine these two velocities. We can do this by subtracting the velocity of the river from the velocity of the canoe. Since the canoe's velocity is southeast and the river's velocity is east, we subtract the eastward velocity of the river from the southeastward velocity of the canoe.
Using vector addition/subtraction techniques, we can determine that the magnitude of the velocity of the canoe relative to the river is the square root of the sum of the squares of their magnitudes. Mathematically, it can be calculated as follows:
Magnitude = √((0.50 m/s)² + (0.54 m/s)²)
= √(0.25 m²/s² + 0.29 m²/s²)
= √(0.54 m²/s²)
≈ 0.62 m/s
To determine the direction of the velocity of the canoe relative to the river, we can use trigonometric principles. The direction can be represented by an angle measured from the positive x-axis in a counterclockwise direction. In this case, since the canoe's velocity is southeast, the angle will be measured from the positive x-axis towards the southeast.
We can use inverse tangent (arctan) to find this angle. Mathematically, it can be calculated as follows:
Direction = arctan((0.50 m/s) / (0.54 m/s))
≈ 44.99 degrees
Therefore, the direction of the velocity of the canoe relative to the river is approximately 45 degrees southeast.
Learn more about Magnitude
brainly.com/question/31022175
#SPJ11
The voltage V, in an electric circuit is measured in millivolts (mV) and is given by the formula
V=0.2sin0.1π(t -0.5)+0.3, where t is the time in seconds from the start of an experiment. Use the graph of the function to estimate how many seconds in the 40 second interval starting at t = 0 during which the voltage is below
0.21mV.
Select one:
a. 14.06
b. 7.03
c. 12.97
d. 27.16
The number of seconds in the 40 second interval starting at t = 0 during which the voltage is below 0.21m V is: 19.06 - 7.03 = 12.03 s = 12.97 (approx.) Thus, the correct option is (c) 12.97.
The voltage V, in an electric circuit is measured in millivolts (mV) and is given by the formula V=0.2
sin0.1π(t -0.5)+0.3, where t is the time in seconds from the start of an experiment. We have to use the graph of the function to estimate how many seconds in the 40 second interval starting at t = 0 during which the voltage is below 0.21mV.
Graph of the given function is shown below:
Graph of the given function
As per the graph, it is observed that the voltage is below 0.21 mV from 7.03 s to 19.06 s.
To learn more on voltage :
https://brainly.com/question/14883923
#SPJ11
what is the magnetic dipole moment of the bar magnet
The magnetic dipole moment of a bar magnet refers to the measure of its strength as a magnetic dipole. It is denoted by the symbol μ (mu) and is defined as the product of the pole strength (magnetic charge) of the magnet and the distance between the poles.
The formula for the magnetic dipole moment (μ) is:
μ = m * d
where:
μ is the magnetic dipole moment,
m is the pole strength (magnetic charge), and
d is the distance between the poles.
The magnetic dipole moment is a vector quantity, meaning it has both magnitude and direction. Its direction is from the south pole to the north pole of the magnet, along the axis of the magnet.
The value of the magnetic dipole moment depends on the characteristics of the specific bar magnet. It can be experimentally determined by measuring the strength of the magnetic field produced by the magnet and the distance between its poles. The SI unit for magnetic dipole moment is the ampere-meter squared (A·m²).
In summary, the magnetic dipole moment of a bar magnet is a measure of its strength as a magnetic dipole and is given by the product of the pole strength and the distance between the poles.
To know more about magnetic dipole click on below link :
https://brainly.com/question/30890387#
#SPJ11
A smoke particle has a mass of about 10−19 kg and a de Broglie wavelength of 10− 15 m, what is the velocity of this particle (in order of magnitude)? 103 m/s 104 m/s 100 m/s 102 m/s
the correct option is 10^2 m/s.
m = 10^(-19) kg
λ = 10^(-15) m
h ≈ 6.626 × 10^(-34) J·s
v = (6.626 × 10^(-34) J·s) / ((10^(-19) kg) * (10^(-15) m))
= (6.626 × 10^(-34) J·s) / (10^(-34) J·m)
= 6.626 × 10^(-34 + 34) m/s
= 6.626 × 10^0 m/s
= 6.626 m/s
Rounded to the nearest order of magnitude, the velocity of the smoke particle is approximately 10^1 m/s. Therefore, the correct option is 10^2 m/s.
To know more about velocity please click :-
brainly.com/question/18084516
#SPJ11
2. If a plasma bubble grows by e
5
in one hour and the Rayleigh-Taylor growth rate scale height is 20 km, what is the ion-neutral collision frequency, assuming the E-Region Pederson conductivity is negligible? [Note: Y
RT
=g/(v
in
∗H),e
∧
(Y
RT
∗t)=5 ]
If a plasma bubble grows by e5 in one hour and the Rayleigh-Taylor growth rate scale height is 20 km, the ion-neutral collision frequency is approximately 9.8 × 10^(-5) Hz.
To determine the ion-neutral collision frequency, we need to calculate the growth rate of the plasma bubble using the Rayleigh-Taylor growth rate equation:
YRT = g / (vin × H)
where:
YRT is the growth rate scale height,
g is the acceleration due to gravity,
vin is the ion-neutral collision frequency, and
H is the scale height.
Given that YRT × t = 5 and H = 20 km, we can rearrange the equation to solve for vin:
YRT = g / (vin × H)
5 = g / (vin × 20 km)
Let's assume the acceleration due to gravity is approximately 9.8 m/s².
Converting the scale height from kilometers to meters:
H = 20 km = 20,000 m
Now we can substitute the values into the equation:
5 = (9.8 m/s²) / (vin × 20,000 m)
Simplifying the equation:
5 × vin × 20,000 = 9.8
100,000 × vin = 9.8
vin = 9.8 / 100,000
vin ≈ 9.8 × 10^(-5) Hz
Therefore, the ion-neutral collision frequency is approximately 9.8 × 10^(-5) Hz.
The question should be:
If a plasma bubble grows by e5 in one hour and the Rayleigh-Taylor growth rate scale height is 20 km, what is the ion-neutral collision frequency, assuming the E-Region Pederson conductivity is negligible? [Note: YRT=g/(vin×H),e∧(YRT× t)=5 ]
To learn more about plasma visit: https://brainly.com/question/950535
#SPJ11
A standing wave is set up on a string of length L, fixed at both ends. If 4-loops are observed when the wavelength is λ = 1.5 m, then the length of the string is:
L = 1.5 m
L = 2.25 m
L = 3.75 m
L = 3 m
L = 0.75 m
A standing wave is set up on a string of length L, fixed at both ends. If 4-loops are observed when the wavelength is λ = 1.5 m, the length of the string is 3 meters (L = 3 m).
The length of the string in this case can be determined by using the relationship between the wavelength, the number of loops (also known as the number of antinodes), and the length of the string.
For a standing wave on a string fixed at both ends, the relationship is given by:
L = (n λ) / 2
Where L is the length of the string, n is the number of loops or antinodes, and λ is the wavelength.
Given that there are 4 loops (n = 4) and the wavelength is 1.5 m, we can substitute these values into the equation to find the length of the string:
L = (4 * 1.5 m) / 2
L = 6 m / 2
L = 3 m
Therefore, the length of the string is 3 meters (L = 3 m).
Learn more about antinodes here:
https://brainly.com/question/30640087
#SPJ11
Are fossil fuels ultimately of solar origin?
Yes, fossil fuels are ultimately of solar origin. Fossil fuels such as coal, oil, and natural gas are formed from the remains of ancient plants and animals that lived millions of years ago.
During their lives, plants and algae absorbed sunlight and used it to convert carbon dioxide and water into carbohydrates through photosynthesis. Over time, these organic materials accumulated and were buried under layers of sediment. The pressure and heat from the Earth's crust transformed them into fossil fuels.
In this sense, the energy stored in fossil fuels can be traced back to the sun. The sunlight captured by plants and algae millions of years ago was preserved in the form of chemical energy in their remains, which later became the fossil fuels we extract and burn for energy today.
To learn more about solar origin follow:
https://brainly.com/question/2549874
#SPJ11
A system consists of three identical particles (same mass), with positions and velocities as follows: T = 21, V₁ = î+ĵ, T₂ = 1, T3 = î-3 k V₂ = 4, V3 = k a) Find the position of the center of mass. (2pts) b) Find the velocity of the center of mass. (2pts) c) Find the linear momentum of the system. (2pts) d) Find the kinetic energy of the system.
a) Position of center of mass The position of center of mass is given as,where,r_1, r_2, and r_3 are position vectors of each particle.m = m₁ + m₂ + m₃, where m is the total mass of the system.From the given data we have,m = m₁ + m₂ + m₃ = m + m + m = 3m.So, the position of the center of mass is r_cm = (r_1 + r_2 + r_3)/3. Therefore, the position of the center of mass is (î + ĵ + î - 3k)/3 = (2î + ĵ - 3k)/3.
b) Velocity of center of mass The velocity of center of mass is given as:
where, v_1, v_2 and v_3 are the velocity vectors of each particle.To find the velocity of center of mass, we need to find the momentum of the system first.c) Momentum of the systemThe momentum of the system is given as, p = m₁v₁ + m₂v₂ + m₃v₃Here, m₁ = m₂ = m₃ = m = 3m (since all the particles have same mass).And, v₁ = î + ĵ, v₂ = 4 and v₃ = k. Therefore, the momentum of the system is p = 3m (î + ĵ + 4 + k).Now, we can use the expression for velocity of center of mass given above to calculate the velocity of center of mass.v_cm = p/m= 3m (î + ĵ + 4 + k) / 3m = î + ĵ + 4/3 + k/3So, the velocity of center of mass is î + ĵ + 4/3 + k/3.
d) Kinetic energy of system The kinetic energy of the system is given as,K = (1/2)m₁v₁² + (1/2)m₂v₂² + (1/2)m₃v₃²Substituting the given values we have, K = (1/2)3m(î + ĵ)² + (1/2)3m(4)² + (1/2)3m(k)²K = (3/2)m(1 + 1 + 16 + k²) = (3/2)m(k² + 18)Therefore, the kinetic energy of the system is (3/2)m(k² + 18).
About Kinetic energyKinetic energy or energy of motion is the energy possessed by an object due to its motion. Kinetic energy of an object is defined as the work required to move an object with a certain mass from rest to a certain speed. Examples of kinetic energy in everyday life include moving windmills, moving cars, cycling, playing yo-yo, bullets fired, and so on.
Learn More About Kinetic energy at https://brainly.com/question/8101588
#SPJ11
In this problem we will consider two waves with wavelengths L1=200 m and L2=500 m
a. For the same ocean depth H=4000 m, are these waves deep-water or shallow-water waves?
b. Will you expect both these waves to move at the same speed? Explain your answer (you do not need to calculate the wave speed at this point)
c. Now check your answer to question (b) by calculating phase speed for each of the two waves (hint: see section 10.3, pp 287-289). Is it what you expected?
d. What are wave periods for these waves?
Explain how you understand the process of wave dispersion. Which of oceanic waves, shallow-water waves or deep-water waves, are dispersive?
a) The formula for deep water waves is L > 1/2 λ and the formula for shallow water waves is L < 1/20 λ. The given wavelengths are L1=200 m and L2=500 m, and the depth of the ocean is H=4000 m.
When substituting the given values in the above two formulas, we can see that both wavelengths are deep-water waves.
b) We expect both the waves to move at the same speed, as the speed of a wave is solely dependent on the wavelength and the ocean depth, and both waves have the same ocean depth
Therefore, their speeds should be the same.c) Phase velocity
(C) for each of the two waves can be calculated by using the following formula:C = (gT/2π)1/2, where g is the acceleration due to gravity, which is 9.81 m/s², and T is the wave period, which can be calculated by using the following formula:T = 2π/ω, where ω is the wave frequency.
By substituting the respective values, the phase speed is calculated as:C1 = (9.81 × 200)1/2/2π = 14.86 m/sC2 = (9.81 × 500)1/2/2π = 23.40 m/s.
Since the phase speeds are different, the wave speed will also be different.
d) The formula for wave period is T = 2π/ω. The frequency of a wave can be calculated by using the following formula:f = C/λ, where C is the wave speed and λ is the wavelength.
By substituting the given values, the wave periods can be calculated as:T1 = 2π/ω1 = 125.6 sT2 = 2π/ω2 = 314.2 s.
The process of wave dispersion is defined as the process of spreading out or separating out of waves with different wavelengths, frequencies, or velocities.
This occurs because the speed of a wave is dependent on both the wavelength and the ocean depth. When a wave moves from deep water to shallow water, the speed of the wave decreases, but the wavelength stays constant.
This results in an increase in the wave's frequency.
Therefore, deep-water waves are not dispersive, but shallow-water waves are dispersive.
Learn more about wave dispersion here ;
https://brainly.com/question/32566323
#SPJ11
The oscillation of an object of on a frictionless surface is characterised by the following parameters: Amplitude = 5.5 cm, Maximum speed = 24.0 cm/s, Position at t = O is x(0) = +2.0 cm,initial velocity is to the left (i.e. (0) <0), mass m = 0.38 kg. (a) Determine the force constant of the spring? (b) determine the angular frequency w of this motion? (c) Calculate the period T of this motion? (d) If the position of the object is x(t) = A cos(wt+0), determine the phase constant, p? Be sure that your answer gives the correct sign for i(0). (e) Write down expressions for x(t) and *(t). +
Determine the force constant of the spring by equating the maximum potential energy stored in the spring to the maximum kinetic energy of the object. Calculate the angular frequency by using the equation w = √(k/m), where k is the force constant and m is the mass.
(a) To determine the force constant of the spring, we can use Hooke's law, which states that the force exerted by a spring is proportional to its displacement. In this case, we have the maximum speed and the mass of the object. The maximum speed corresponds to the maximum kinetic energy, which is equal to the maximum potential energy stored in the spring. Therefore, we can use the equation (1/2)kA^2 = (1/2)mv^2, where k is the force constant, A is the amplitude, m is the mass, and v is the maximum speed. Plugging in the values, we can solve for k.
(b) The angular frequency w can be calculated using the equation w = √(k/m), where k is the force constant and m is the mass
(c) The period T can be calculated using the equation T = (2π)/w, where w is the angular frequency.
(d) To determine the phase constant p, we need to use the given position x(t) = A cos(wt + p) and the initial condition x(0) = +2.0 cm. By substituting the values, we can solve for p.
(e) The expressions for x(t) and v(t) are x(t) = A cos(wt + p) and v(t) = -wA sin(wt + p), respectively.
To know more about Hooke's law,
https://brainly.com/question/29126957
#SPJ11
An AC source has a maximum voltage of 170 V and a frequency of 60 Hz. A capacitor circuit using this AC source and a capacitor of 4×10−6 F has a maximum current of 0.320 A 0.128 A 0.256 A. 0.192 A.
The maximum current in the capacitor circuit is approximately 0.324 A.
I = C * dV/dt
Where dV/dt represents the rate of change of voltage with respect to time.
In an AC circuit, the voltage follows a sinusoidal waveform given by:
V = Vmax * sin(ωt)
Where Vmax is the maximum voltage, ω is the angular frequency (2πf), and t is time.
Taking the derivative of the voltage waveform, we have:
dV /dt = Vmax * ω * cos(ωt)
Substituting the values into the current formula:
I = (4 × 10^(-6) F) * (170 V) * (120π rad/s) * cos(ωt)
Since we are interested in the maximum current, we can ignore the cos(ωt) term since it will have a maximum value of 1.
Therefore, the maximum current is:
I = (4 × 10^(-6) F) * (170 V) * (120π rad/s)
≈ 0.324 A
To know more about capacitor please click :-
brainly.com/question/31627158
#SPJ11
the stanford linear accelerator (slac) accelerates electrons to
The Stanford Linear Accelerator (SLAC) accelerates electrons to a maximum energy of 50 GeV. It is a 2 mile long linear accelerator located in Menlo Park, California. SLAC is used for a variety of experiments, including studies of elementary particles, astrophysics, and materials science.
Here are some of the things that SLAC is used for:
Elementary particle physics: SLAC is used to study the fundamental particles that make up matter. By accelerating electrons to high energies and colliding them with other particles, physicists can study the properties of these particles and how they interact. Astrophysics: SLAC is used to study the universe beyond our solar system. By studying the properties of cosmic rays, which are high-energy particles that come from space, physicists can learn about the processes that occur in stars and galaxies. Materials science: SLAC is used to study the properties of materials. By accelerating electrons to high energies and shining them on materials, physicists can study how the electrons interact with the material and how this interaction affects the properties of the material.To learn more about matter visit: https://brainly.com/question/3998772
#SPJ11
an object with 15 grams mass is immersed in benzene
When an object with a mass of 15 grams is immersed in benzene, the weight of the object will be equal to the buoyant force exerted by the liquid.
The buoyant force experienced by an object immersed in a fluid is given by Archimedes' principle, which states that the buoyant force is equal to the weight of the fluid displaced by the object.
The weight of the object is given by the equation:
Weight = mass * gravitational acceleration
Assuming the gravitational acceleration is approximately 9.8 m/s^2, the weight of the object is:
Weight = 15 grams * 9.8 m/s^2
To determine the buoyant force, we need to know the density of benzene. The density of benzene is approximately 0.88 g/cm^3.
The volume of the object can be calculated using the equation:
Volume = mass / density
Plugging in the values, we get:
Volume = 15 grams / 0.88 g/cm^3
Once we have the volume of the object, we can calculate the buoyant force using the equation:
Buoyant Force = Density of Fluid * Volume of Object * gravitational acceleration
Substituting the values, we find:
Buoyant Force = 0.88 g/cm^3 * Volume * 9.8 m/s^2
Since the weight of the object is equal to the buoyant force, we can equate the two and solve for the volume of the object. Finally, we can substitute the volume into the buoyant force equation to determine the exact value.
Learn more about immersed in benzene here:
https://brainly.com/question/31650190
#SPJ11
what is the term for materials that have very low thermal energy and resistance?
The term for materials that have very low thermal energy and resistance is "thermal insulators" or simply "insulators."
Thermal insulators are materials that exhibit low thermal conductivity, meaning they are not efficient at conducting heat. These materials have properties that impede the transfer of thermal energy through them. As a result, they provide resistance to the flow of heat and help to prevent or reduce heat transfer.
Examples of common thermal insulators include materials such as foam, fiberglass, cellulose, wool, plastic, rubber, and certain types of ceramics. These materials are often used in building insulation, protective clothing, packaging, and various other applications where reducing heat transfer is desirable.
In contrast, materials with high thermal conductivity, such as metals like copper or aluminum, are called "thermal conductors" as they facilitate the efficient transfer of heat.
Hence, The term for materials that have very low thermal energy and resistance is "thermal insulators" or simply "insulators."
To know more about thermal insulators here
https://brainly.com/question/23134662
#SPJ4
An ideal gas with n = 0.50 mol is shut off by a movable piston in a cylinder.
When an ideal gas with n = 0.50 mol is shut off by a movable piston in a cylinder, there are several factors that can affect the behavior of the gas. One of the most important factors is the pressure of the gas, which can be affected by the volume of the cylinder and the temperature of the gas.
Another factor that can affect the behavior of the gas is the type of gas itself. An ideal gas is a theoretical gas that is made up of particles that have no volume, are in constant motion, and do not interact with each other. This means that an ideal gas will always behave in a predictable way, no matter what the conditions are.
However, real gases do not behave in this way. Real gases have volume and interact with each other, which means that they will behave differently depending on the conditions. For example, if the temperature of a gas is increased, the volume of the gas will also increase. Similarly, if the pressure of the gas is increased, the volume of the gas will decrease.
In addition to these factors, the behavior of the gas can also be affected by the shape of the cylinder and the position of the piston. If the cylinder is narrow and the piston is close to the gas, the gas will be compressed and the pressure will increase. Conversely, if the cylinder is wide and the piston is far from the gas, the gas will expand and the pressure will decrease.
As the given question is incomplete, the complete question is "An ideal gas with n = 0.50 mol is shut off by a movable piston in a cylinder. Which factors affect the behavior of the gas?"
You can learn more about pressure at: brainly.com/question/29830939
#SPJ11
Chinook samen can cover more distance in less time by periodially making yumps out of the water suppose a salmon swimming in still water jumps out of the water with yelocity 5.63 mys at 45.64 above the horizontal, re enters the water a distance L upstream, and then swims the same datance L underwater in a straight, horizontal ine with velocity 2.92 mis befare jumping out again. (a) What is the fish's awerage herizontal velocitv (in m/s) between jumps? (Round your answer to at least 2 decimal places-) m/s (b) Consider the interval of time necessary to travel 24 . How is this reduced by the combinstion of jumping and swimming compared with just swimming at the constant speed of 2.92 m/s? Express the reduction as a pertentage. \% reduction (c) What in Some saimen are able to jump a distance L qut of the water while only swimming a distance
4
L
between jumps. Ey what percentege are these saimon faster than those requring an underwater swim of Gstance L ? (Assume the salmon jumps cut of the water wath velocty 5.63 m's at 45.6
∘
above the horisontal, reienters the water a cstance L upstream, and then swims a distance
4
L
underwater in a straight, horizontal line with velocity 2.92 mis before jumping out again } O faster
The salmon that can jump a distance L while only requiring an underwater swim of L/4 is faster than those that require an underwater swim of distance L by 69.03%.The percentage reduction in time is 13.95%
(a) The average horizontal velocity of the fish between jumps can be determined using the equation for the range of a projectile.
The range, R, is given by the equation R = v₀² sin(2θ) / g where:v₀ is the initial velocityθ is the angle of launch g is the acceleration due to gravity.
For the given values:v₀ = 5.63 m/sθ = 45.64°g = 9.81 m/s²R = 2Lsin(θ) = 2Lsin(45.64°) = 2L(0.694) = 1.388L.
The time taken to cover a distance of 2L is given by the equation t = 2L / v where v is the velocity.
Between jumps, the fish moves through the air for a time t₁ = R / v₀ and then swims underwater for a time t₂ = L / v.
The average horizontal velocity, vₐᵥ, is given by the equationvₐᵥ = 2L / (t₁ + t₂).
Substituting the given values givesvₐᵥ = 2L / [(R / v₀) + (L / v)]vₐᵥ = 2L / [(1.388L / 5.63) + (L / 2.92)]vₐᵥ = 2L / (0.2465L + 0.3425L)vₐᵥ = 2L / 0.589L = 3.394 m/s (2 decimal places)
(b) If the fish had swum continuously underwater at a speed of 2.92 m/s, it would have taken a time t = 2L / v = 2L / 2.92 = 0.6849L.
During this time, the fish would have travelled a distance of 2L at an average speed of 2.92 m/s, so it would have taken a time t = 2L / (2.92) = 0.6849L.
The time taken using the jumping and swimming technique is t₁ + t₂ = R / v₀ + L / v = (1.388L / 5.63) + (L / 2.92) = 0.2465L + 0.3425L = 0.589L.
The percentage reduction in time is given by [(0.6849L - 0.589L) / (0.6849L)] x 100% = 13.95% (2 decimal places)
(c) If the fish can jump a distance of L and only needs to swim a distance of L/4 between jumps, then the range, R, is given by R = 2Lsin(θ) = 2(L/4) / cos(θ) = 0.5L / cos(θ).
Using the given values for θ and solving for cos(θ),cos(θ) = cos(45.64°) = 0.7013R = 0.5L / cos(θ) = 0.5L / 0.7013 = 0.713L.
The time taken to travel a distance of R is t = R / v₀ = (0.713L) / 5.63 = 0.1265L.
The time taken to swim a distance of L/4 is t = (L/4) / 2.92 = 0.08562L.
The total time for a jump and swim is t = t + t = 0.1265L + 0.08562L = 0.2121L.
The percentage reduction in time compared to a salmon that requires an underwater swim of distance L is [(0.6849L - 0.2121L) / (0.6849L)] x 100% = 69.03% (2 decimal places).
Therefore, the salmon that can jump a distance L while only requiring an underwater swim of L/4 is faster than those that require an underwater swim of distance L by 69.03%.
Learn more about acceleration here ;
https://brainly.com/question/30660316
#SPJ11
Starting from rest, a car accelerates at 2.8 m/s2 up a hill that is inclined 5.6 degrees above the horizontal.
How far horizontally has the car traveled in 11 s ?
How far vertically has the car traveled in 11 s ?
To solve this problem, we'll need to use the equations of motion and consider the horizontal and vertical components separately. After calculations through the formula, we found that the car has traveled approximately 169.4 meters horizontally in 11 seconds. Moreover, the car traveled approximately 592.9 meters vertically in 11 seconds.
The horizontal distance traveled can be determined using the formula: d = v₀ * t + 0.5 * a * t².
where:
d is the distance traveled horizontally.
v₀ is the initial velocity (which is 0 m/s since the car starts from rest).
a is the acceleration, t is the time.
a = 2.8 m/s² (acceleration).
t = 11 s (time).
d = 0 * 11 + 0.5 * 2.8 * (11)².
d = 0 + 0.5 * 2.8 * 121.
d = 0 + 0.5 * 2.8 * 121.
d = 0 + 0.5 * 338.8.
d = 0 + 169.4.
d = 169.4 meters.
Therefore, the car has traveled approximately 169.4 meters horizontally in 11 seconds.
The vertical distance traveled can be calculated using the formula: d = v₀ * t + 0.5 * a * t².
where:
d is the vertical distance traveled.
v₀ is the initial velocity (which is 0 m/s since the car starts from rest).
a is the acceleration (which is due to gravity, approximately 9.8 m/s²).
t is the time.
a = 9.8 m/s² (acceleration due to gravity).
t = 11 s (time).
d = 0 * 11 + 0.5 * 9.8 * (11)².
d = 0 + 0.5 * 9.8 * 121.
d = 0 + 0.5 * 9.8 * 121.
d = 0 + 0.5 * 1185.8.
d = 0 + 592.9.
d = 592.9 meters.
Therefore, the car has traveled approximately 592.9 meters vertically in 11 seconds.
Read more about the Acceleration of the car.
https://brainly.com/question/28935879
#SPJ11
QUESTION 1 If a 23.0 N horizontal force must be applied to slide a 13.3 kg box along the floor at constant velocity what is the coefficient of sliding friction between the two surfaces? Note 1: The units are not required in the answer in this instance. Note 2: If rounding is required, please express your answer as a number rounded to 2 decimal places. QUESTION 2 A furniture removalist applies a 857.3 N force vertically upward to lift a 56.0 kg box. What is the resultant NET force acting on the box? Note 1: The units are not required in the answer in this instance. Note 2: If rounding is required, please express your answer as a number rounded to 2 decimal places. Note 3: Remember that downwards is negative, meaning the direction of some parameters may need to be indicated as per the instructions presented at the beginning of the quiz.
1. The coefficient of sliding friction between the two surfaces is 0.1767. 2) The resultant net force acting on the box is 308.5 N.
1. For the first question, to find the coefficient of sliding friction, divide the applied horizontal force by the weight of the box. The applied horizontal force is given as 23.0 N, and the weight of the box can be calculated using the formula
weight = mass × acceleration due to gravity.
Thus, weight = [tex]13.3 kg * 9.8 m/s^2 = 130.34 N[/tex].
Dividing the applied horizontal force by the weight gives us the coefficient of sliding friction:
23.0 N / 130.34 N = 0.1767
2. Moving on to the second question, to determine the resultant net force acting on the box, need to consider both the applied force and the weight of the box. The applied force is given as 857.3 N vertically upward, and the weight of the box can be calculated as before:
weight = [tex]56.0 kg * 9.8 m/s^2 = 548.8 N[/tex].
Since the applied force is directed upward and the weight acts downward (negative), subtract the weight from the applied force:
857.3 N - 548.8 N = 308.5 N
Therefore, the resultant net force acting on the box is 308.5 N.
Learn more about sliding friction here:
https://brainly.com/question/17140804
#SPJ11
A mass-spring-dashpot has the total energy E = 1/2 m v² + 1/2 k x², where v = dx/dt. In class we showed that E is constant when = 0. Show that when > 0, energy is always dissipated. Hint: look at dE/dt and use the governing differential equation
A mass-spring-dashpot has the total energy E = 1/2 m v² + 1/2 k x², where v = dx/dt. In class, we showed that E is constant when = 0. Show that when > 0, energy is always dissipated.
Hint: look at dE/dt and use the governing differential equation A mass-spring-dashpot is an instrument that can be used to measure dynamic mechanical properties. It can be used to determine stiffness, damping, and hysteresis. It is made up of a mass, a spring, and a dashpot (or damper).
It is commonly used in mechanical engineering to study the behavior of mechanical systems.There are two types of mass-spring-dashpots: linear and nonlinear. Linear mass-spring-dashpots are the most common type. They are used in many applications, including vibration isolation, shock absorption, and dynamic analysis.
Nonlinear mass-spring-dashpots are used in applications where the damping force changes with displacement or velocity.In class, it was demonstrated that the total energy E = 1/2 m v² + 1/2 k x² of a mass-spring-dashpot is constant when = 0. This implies that energy is conserved when there is no external force acting on the system.When > 0, energy is always dissipated.
To know more energy visit:
https://brainly.com/question/1932868
#SPJ11
A water gun shots water from a height of 4 m and the water
touches the ground at 6m in the horizontal direction. With what
velocity does the water hit the ground?
The initial height of the water gun, `h = 4 m`. The horizontal distance covered by the water before hitting the ground, `x = 6 m`. The final vertical displacement of the water, `y = 0` (since it hits the ground). The acceleration due to gravity, `g = 9.8 m/s²`.
The velocity with which the water hits the ground can be found using the formula for projectile motion, which relates the horizontal distance traveled by the projectile, its initial velocity, the angle of projection, and the acceleration due to gravity.`x = (v₀ cosθ)t.
`Here, `v₀` is the initial velocity and `θ` is the angle of projection, which is 90° in this case (since the water is being shot straight up and falls back down).
The time taken for the water to fall back down to the ground can be found using the formula for the final velocity of a falling object.`v = u + gt`.
Here, `u` is the initial velocity (which is 0 since the water is released from rest), `g` is the acceleration due to gravity, and `t` is the time taken for the water to fall back down to the ground.
Substituting `y = 0` and `u = 0` in the formula, we get:`v = gt`.
Now, we can substitute `x`, `v₀` (which we want to find), `θ = 90°`, `g`, and `t` (which we can find using the above equation) into the formula for horizontal distance:`x = (v₀ cosθ)t = v₀(0)t = 0`.
Solving for `t`, we get:`t = sqrt(2h/g) = sqrt(2 × 4/9.8) ≈ 0.90 s.
`Now, we can substitute `t` into the equation for vertical velocity:`v = gt = 9.8 × 0.90 ≈ 8.82 m/s.
`Therefore, the water hits the ground with a velocity of approximately `8.82 m/s`.
Learn more about distance here ;
https://brainly.com/question/13034462
#SPJ11
Two identical point charges are a fixed distance apart. By what factor would the magnitude of the electric force betweenthem change if: a) one of their charges were doubledand the other were halved, b) both their charges were halved,and c) one charge were halved and the other were leftunchanged?
(a) If one of the charges is doubled while the other is halved, the magnitude of the electric force between them would change by a factor of 4.
(b) If both charges are halved, the magnitude of the electric force between them would change by a factor of 1/4.
(c) If one charge is halved while the other is left unchanged, the magnitude of the electric force between them would change by a factor of 1/2.
The electric force between two point charges is given by Coulomb's law:
F = k * |q1 * q2| / r^2
where F is the electric force, k is the electrostatic constant, q1 and q2 are the charges, and r is the distance between the charges.
(a) If one of the charges is doubled (2q) while the other is halved (q/2), the new electric force would be:
F' = k * |(2q) * (q/2)| / r^2 = k * |q^2| / r^2
The ratio of the new force to the original force is:
F' / F = (k * |q^2| / r^2) / (k * |q * q| / r^2) = (q^2 / (q * q)) = q / q = 1
Therefore, the magnitude of the electric force remains unchanged.
(b) If both charges are halved (q/2 and q/2), the new electric force would be:
F' = k * |(q/2) * (q/2)| / r^2 = k * |(q^2/4)| / r^2 = (1/4) * k * |q^2| / r^2
The ratio of the new force to the original force is:
F' / F = ((1/4) * k * |q^2| / r^2) / (k * |q * q| / r^2) = (q^2 / (4 * q * q)) = 1/4
Therefore, the magnitude of the electric force is reduced by a factor of 1/4.
(c) If one charge is halved (q/2) while the other is left unchanged (q), the new electric force would be:
F' = k * |(q/2) * q| / r^2 = (1/2) * k * |q^2| / r^2
The ratio of the new force to the original force is:
F' / F = ((1/2) * k * |q^2| / r^2) / (k * |q * q| / r^2) = (q^2 / (2 * q * q)) = 1/2
Therefore, the magnitude of the electric force is reduced by a factor of 1/2.
Learn more about magnitude of the electric force here:
https://brainly.com/question/33458657
#SPJ11
In which part of a newborn star does the fusion reaction occur?
a) in all parts of the star.
b) the radiation zone.
c) the core.
d) the convection zone.
The fusion reaction in a newborn star primarily occurs in the core.
Hence, the correct option is C.
The core of a newborn star is the region where the conditions of temperature and pressure are sufficient to sustain nuclear fusion. It is in the core that the high temperatures and densities enable the fusion of hydrogen nuclei (protons) into helium nuclei, releasing energy in the process.
In the early stages of stellar evolution, a newborn star forms from a collapsing cloud of gas and dust. As the material in the core becomes denser and hotter due to gravitational contraction, the core reaches the necessary conditions for fusion to occur. At this point, the energy generated by nuclear fusion counteracts the inward gravitational forces, establishing a stable equilibrium and allowing the star to shine.
The radiation zone and the convection zone are other regions within a star, but they are not primarily responsible for the fusion reactions. The radiation zone is the region above the core where energy is transported primarily by photons through a process of radiation. The convection zone is the outermost layer of a star, characterized by convective currents that transport energy through the rising and falling of hot gas.
While fusion reactions occur in the core, the energy produced through fusion eventually radiates outwards through the radiation zone and the convection zone before being released into space as heat and light.
Therefore, The fusion reaction in a newborn star primarily occurs in the core.
Hence, the correct option is C.
To know more about fusion reaction here
https://brainly.com/question/28020465
#SPJ4
2.) An RLC circuit is composed of a resistor R = 350 2, capacitor C = 3.0 uF, an inductor L = 6.0 mH, and a battery with a maximum voltage of Em = 5.0 V and an angular frequency of 50 rads/s. (a) What is the total impedance of the circuit? (b) Calculate the phase difference between the current and the applied voltage. (c) What is the maximum current in the circuit. (d) Write down the equation of the current through the circuit.
(a) The impedance of the circuit is given by the formula Z = √((R^2 + (ωL - 1/(ωC))^2)), where R is the resistance, L is the inductance, C is the capacitance, and ω is the angular frequency of the battery. Substituting the given values, we get:
Z = √((350^2 + (50*6*10^-3 - 1/(50*3*10^-6))^2))
= √((122500 + (0.18 - 33333.33)^2))
= √((122500 + 33333.15^2))
= 1.0 x 10^5 Ω
(b) The phase difference between the current and the applied voltage is given by the formula tanθ = ((ωL - 1/(ωC))/R). Solving for θ:
θ = tan^(-1)(((50*6*10^-3 - 1/(50*3*10^-6))/350))
= 0.42 radians
(c) The maximum current in the circuit is given by Imax = Em/Z, where Em is the maximum voltage and Z is the impedance of the circuit:
Imax = 5.0 / 1.0 x 10^5
= 5.0 x 10^-5 A
(d) The current through the circuit can be represented by the equation: i(t) = Imaxsin (ωt - θ), where ω is the angular frequency and θ is the phase difference:
i(t) = (5.0 x 10^-5)sin(50t - 0.42)
Answer:
The total impedance of the circuit = 1.0 x 10^5 Ω
The phase difference between the current and the applied voltage = 0.42 radians
The maximum current in the circuit = 5.0 x 10^-5 A
The equation of the current through the circuit is given by i(t) = (5.0 x 10^-5)sin(50t - 0.42), where i is the current at time t.
To learn more about impedance, phase difference, and related concepts, click this link:
brainly.com/question/14974039
#SPJ11
In most of our daily experience of touch, we are using _____.
a. passive touch
b. active touch
c. two-point touch
d. two-hand touch.
In most of our daily experience of touch, we are using passive touch.
Hence, the correct option is A.
Passive touch refers to the sensory perception of touch without active exploration or movement. It involves the detection and interpretation of tactile sensations through the skin and other sensory receptors without actively engaging in physical contact or manipulation.
In our daily lives, passive touch is the most common form of touch that we encounter. Examples include feeling the texture of objects, sensing temperature, experiencing pressure, or perceiving vibrations. Passive touch allows us to gather information about our surroundings and interact with objects without actively initiating movement or exploration.
Active touch, on the other hand, involves actively exploring and manipulating objects through touch. It often involves coordinated movements, such as using our hands and fingers to explore the texture, shape, and properties of objects. Active touch is commonly employed in tasks that require fine motor skills, precise control, and detailed sensory feedback.
The terms "two-point touch" and "two-hand touch" are not widely used in the context of touch perception and are not relevant to the distinction between passive and active touch.
Therefore, In most of our daily experience of touch, we are using passive touch.
Hence, the correct option is A.
To know more about passive touch here
https://brainly.com/question/28258463
#SPJ4