If there is a significant difference between the two answers, it could indicate a mistake in the calculations or the graphical representation. It's important to carefully check the calculations and ensure accurate measurements and angles are used.
In this problem, we need to find the magnitude and position of the balance mass in a rotating shaft. We can approach this using two methods: the graphical method (Angular Position diagram and Vector diagram) and the analytical method.
2.1 Graphical Method
To find the balance mass using the graphical method, we can construct an Angular Position diagram and a Vector diagram. In the Angular Position diagram, we plot the masses at their respective angles. In the Vector diagram, we represent the magnitudes and directions of the masses as vectors. By adjusting the magnitude and position of the balance mass vector, we can achieve balance in the system. The magnitude of the balance mass can be determined by measuring the length of the balanced vector.
2.2 Analytical Method:
To determine the balance mass using the analytical method, we can sum the moments of the masses about the desired position of the balance mass. The moment is calculated by multiplying the mass with its radius of rotation and the sine of the angle it makes with the horizontal. By setting the sum of the moments equal to zero, we can solve for the magnitude and position of the balance mass.
2.3 Comparison:
The two methods should provide the same result for the magnitude and position of the balance mass. However, there may be slight differences due to measurement errors in the graphical method or rounding errors in the analytical method. In practice, the analytical method is generally more accurate and precise.
If there is a significant difference between the two answers, it could indicate a mistake in the calculations or the graphical representation. It's important to carefully check the calculations and ensure accurate measurements and angles are used. In such cases, repeating the calculations and double-checking the inputs can help identify and rectify any errors.
Overall, both methods should yield similar results for the balance mass, but the analytical method is generally more reliable.
Learn more about rotating shaft here:
https://brainly.com/question/31433596
#SPJ11
The voltage V ,in an electric circuit is measured in millivolts (mV) and is given by the formula V=0.2sin0.1π(t−0.5)+0.3, where t is the time in seconds from the start of an experiment. Use the graph of the function to estimate how many seconds in the 40 second interval starting at t=0 during which the voltage is below 0.21mV Select one:
a. 14.06
b. 7.03
c. 12.97
d. 27.16
In order to find the seconds in the 40-second interval starting at t=0 during which the voltage is below 0.21mV, we need to find out the value of t when V < 0.21.
Given function is V=0.2sin0.1π(t−0.5)+0.3.
Therefore, 0.2sin0.1π(t−0.5)+0.3 < 0.21 can be written as0.2sin0.1π(t−0.5) < 0.21 - 0.3=-0.09sin0.1π(t−0.5) < -0.45sin0.1π(t−0.5) = -(0.1π/2) + nπt = [-(0.1π/2) + nπ]/0.1π + 0.5where n is any integer.
In the given function, the coefficient of t is 0.1π. Hence the time period of this function can be given by T = 2π / (0.1π)=20 seconds.
Now we need to find out how many times the value of sin0.1π(t−0.5) will be less than -0.45 during the first 40 seconds, starting from t = 0.
We need to check the function for t=0, t=20, and t=40.
By doing so, we get the following values of t:t = 0 V = 0.2sin0.1π(-0.5)+0.3= 0.2sin(-π/20)+0.3= 0.2493t = 20 V = 0.2sin0.1π(19.5)+0.3= 0.7t = 40 V = 0.2sin0.1π(39.5)+0.3= 0.2507
From the above values, it is clear that sin0.1π(t−0.5) will be less than -0.45 during the time interval t = 2 to t = 4 seconds and during the time interval t = 18 to t = 22 seconds.
Therefore, the number of seconds in the 40 second interval starting at t = 0 during which the voltage is below 0.21 mV is:2 + (22 - 18) = 2 + 4 = 6 seconds.
Therefore, option (B) 7.03 seconds is incorrect as the correct answer is 6 seconds.
To know more about voltage visit:
https://brainly.com/question/32002804
#SPJ11
Light traveling in air ( n_air =1.00) is incident on an equilateral glass prism (n_glass=1.5) at a 45° angle to one face. Calculate the angle at which light emerges from the opposite face? [3] How long does it take for a pulse of light to pass through a 6 cm thick flint-glass plate? (n_flint-glass =1.66)
It takes 3.32 * 10^(-10) seconds for a pulse of light to pass through a 6 cm thick flint-glass plate.
To calculate the angle at which light emerges from the opposite face of an equilateral glass prism, we can use Snell's law, which relates the angles and refractive indices of the incident and refracted light.
Given:
Incident angle (θ1) = 45°
Refractive index of air (n_air) = 1.00
Refractive index of glass (n_glass) = 1.5
Using Snell's law:
n1 * sin(θ1) = n2 * sin(θ2)
where n1 and n2 are the refractive indices of the initial and final mediums, and θ2 is the angle of refraction.
Plugging in the values:
1.00 * sin(45°) = 1.5 * sin(θ2)
sin(θ2) = (1.00 * sin(45°)) / 1.5
sin(θ2) ≈ 0.4714
To find θ2, we can take the inverse sine (sin^(-1)) of 0.4714:
θ2 ≈ sin^(-1)(0.4714)
θ2 ≈ 28.8°
Therefore, the angle at which light emerges from the opposite face of the glass prism is approximately 28.8°.
Now, let's calculate the time it takes for a pulse of light to pass through a 6 cm thick flint-glass plate.
Given:
Thickness of the flint-glass plate (d) = 6 cm
Refractive index of flint-glass (n_flint-glass) = 1.66
The speed of light in a medium is given by:
v = c / n
where v is the speed of light in the medium, c is the speed of light in a vacuum, and n is the refractive index of the medium.
The time it takes for the pulse of light to pass through the glass plate is:
t = d / v
First, let's calculate the speed of light in flint-glass:
v = c / n_flint-glass
Substituting the values:
v = (3.00 * 10^8 m/s) / 1.66
Now, let's calculate the time:
t = (6 cm) / v
Note: We need to convert the thickness of the flint-glass plate to meters (since the speed of light is given in meters per second).
Substituting the values and converting cm to meters:
t = (6 * 10^(-2) m) / v
Now, we can evaluate the expression:
t ≈ (6 * 10^(-2) m) / [(3.00 * 10^8 m/s) / 1.66]
t ≈ 3.32 * 10^(-10) s
Therefore, it takes approximately 3.32 * 10^(-10) seconds for a pulse of light to pass through a 6 cm thick flint-glass plate.
Learn more about pulse from the given link
https://brainly.com/question/17245697
#SPJ11
A diver of mass 69.7 kg stands on one end of a diving board of mass 36.2
kg, as shown in the diagram. Everything is in equilibrium (since nothing is
moving). What is the magnitude of the support force on the opposite end of
the diving board?
The magnitude of a force cannot be negative, the magnitude of the support force on the opposite end of the diving board is approximately 1036.82 N.
To find the magnitude of the support force on the opposite end of the diving board, we can analyze the forces acting on the system.
Considering the equilibrium of the system, we can start by examining the forces acting vertically:
Weight of the diver (acting downwards):
F_d = m_d g
Weight of the diving board (acting downwards):
F_b = m_b g
Next, let's consider the forces acting horizontally:
Support force at the opposite end of the diving board (acting to the right):
F_support
Since the system is in equilibrium, the sum of the forces in the vertical direction must be zero:
F_d + F_b + F_support = 0
Substituting the expressions for the weights of the diver and the diving board:
m_d g + m_b g + F_support = 0
Now we can solve for the support force (F_support):
F_support = - (m_d g + m_b g)
Substituting the given values:
m_d = 69.7 kg
m_b = 36.2 kg
g = 9.8 m/s²
F_support = - (69.7 kg * 9.8 m/s² + 36.2 kg * 9.8 m/s²)
F_support = - (682.06 N + 354.76 N)
F_support ≈ - 1036.82 N
Learn more about force here:
https://brainly.com/question/30526425
#SPJ11
A wire with mass 45.0 g is stretched so that its ends are tied down at points a distance 84.0 cm apart. The wire vibrates in its fundamental mode with frequency 65.0 Hz and with an amplitude at the antinodes of 0.280 cm. For related problemsolving tips and strategies, you may want to view a Video Tutor Solution of A giant bass viol. Part B Compute the tension in the wire. Express your answer in newtons. Find the magnitude of the maximum transverse velocity of particles in the wire. Express your answer in meters per second. Part D Find the magnitude of the maximum acceleration of particles in the wire. Express your answer in meters per second squared.
The tension in the wire is approximately 7.12 N.
The magnitude of the maximum transverse velocity of particles in the wire is approximately 1.463 m/s.
The magnitude of the maximum acceleration of particles in the wire is approximately 152.29 m/s².
To find the tension in the wire, we can use the formula:
Tension = (mass per unit length) * (velocity of wave)²
The mass per unit length of the wire can be calculated by dividing the total mass of the wire by its length. Given that the mass of the wire is 45.0 g and the length is 84.0 cm, the mass per unit length is 0.536 g/cm.
Converting the mass per unit length to kg/m, we get 5.36 kg/m.
Since the wire vibrates in its fundamental mode, the velocity of the wave is equal to the product of the frequency and the wavelength. The wavelength can be calculated by dividing the length of the wire (84.0 cm) by 2, as the wire is tied down at both ends. Thus, the wavelength is 42.0 cm or 0.42 m.
Multiplying the frequency (65.0 Hz) by the wavelength (0.42 m), we get the velocity of the wave as 27.3 m/s.
Now, plugging in the values into the tension formula, we get:
Tension = (5.36 kg/m) * (27.3 m/s)² ≈ 7.12 N.
To find the maximum transverse velocity of particles in the wire, we can use the formula:
Maximum transverse velocity = (angular frequency) * (amplitude)
The angular frequency can be calculated by multiplying 2π with the frequency. Thus, the angular frequency is approximately 408.41 rad/s.
Plugging in the angular frequency and the given amplitude (0.280 cm or 0.0028 m) into the formula, we get:
Maximum transverse velocity = (408.41 rad/s) * (0.0028 m) ≈ 1.463 m/s.
To find the maximum acceleration of particles in the wire, we can use the formula:
Maximum acceleration = (angular frequency)² * (amplitude)
Plugging in the angular frequency (408.41 rad/s) and the amplitude (0.0028 m) into the formula, we get:
Maximum acceleration = (408.41 rad/s)² * (0.0028 m) ≈ 152.29 m/s².
Learn more about Acceleration
brainly.com/question/2303856
#SPJ11
10 A disk with moment of inertia I, is rotating with initial angular speed : a second disk with moment of inertia I, initially is not rotating. The arrangement is much like a LP record ready to drop onto an unpowered, freely spinning turntable. The second disk drops onto the first and friction between them brings them to a common angular speed. Find the common angular speed co Hu
The common angular speed when the two disks come to rest is given by the ratio of the initial angular speed of the first disk to the total moment of inertia of the system
To find the common angular speed when the two disks come to rest, we can apply the principle of conservation of angular momentum. The initial angular momentum of the system is zero because one disk is not rotating, and the other is rotating with an initial angular speed.
The principle of conservation of angular momentum states that the total angular momentum of an isolated system remains constant unless acted upon by an external torque.
Mathematically, we can express this principle as:
I1 * ω1 + I2 * ω2 = I1 * ωf + I2 * ωf
where
I1 and I2 are the moments of inertia of the two disks,
ω1 and ω2 are the initial angular speeds of the two disks,
and ωf is the common angular speed when the disks come to rest.
Since the second disk is initially not rotating (ω2 = 0), the equation simplifies to:
I1 * ω1 = (I1 + I2) * ωf
Solving for ωf, we have:
ωf = (I1 * ω1) / (I1 + I2)
Therefore, the common angular speed when the two disks come to rest is given by the ratio of the initial angular speed of the first disk to the total moment of inertia of the system (sum of the moments of inertia of both disks).
Learn more about angular speed here:
https://brainly.com/question/29058152
#SPJ11
Assume for the solidification of nickel that nucleation is homogeneouswith ΔG* = 1.27 x 10 18 J, ΔHf = -2.53 x 109 J/m3 andthe number of stable nuclei is 106 nuclei/m3. Calculate the criticalradius and the number of stable nuclei that exist the followingdegrees of supercooling: 200 K and 300 K
For the solidification of nickel with homogeneous nucleation, at a supercooling of 200 K, the critical radius is approximately 1.80 x 10^(-8) meters, and the number of stable nuclei is approximately 1.21 x 10^18 nuclei/m^3. At a supercooling of 300 K, the critical radius is approximately 2.11 x 10^(-8) meters, and the number of stable nuclei is approximately 1.64 x 10^21 nuclei/m^3.
The critical radius, denoted as r*, can be calculated using the relation between the critical Gibbs free energy change (ΔG*) and the latent heat of fusion (ΔHf):
r* = (2 * ΔHf / ΔG*)^(1/3)
Plugging in the given values, we have:
r* = (2 * (-2.53 x 10^9 J/m^3) / (1.27 x 10^18 J))^(1/3)
Calculating the critical radius, we find:
r* ≈ 1.80 x 10^(-8) meters
The number of stable nuclei, denoted as Ns, can be determined using the relation:
Ns = (ΔG*)^3 / (4π * (ΔHf)^2)
Plugging in the given values, we have:
Ns = (1.27 x 10^18 J)^3 / (4π * (-2.53 x 10^9 J/m^3)^2)
Calculating the number of stable nuclei, we get:
Ns ≈ 1.21 x 10^18 nuclei/m^3
Similarly, we can repeat the calculations for a supercooling of 300 K. The critical radius is found to be approximately 2.11 x 10^(-8) meters, and the number of stable nuclei is approximately 1.64 x 10^21 nuclei/m^3.
Therefore, at a supercooling of 200 K, the critical radius is approximately 1.80 x 10^(-8) meters, and the number of stable nuclei is approximately 1.21 x 10^18 nuclei/m^3. At a supercooling of 300 K, the critical radius is approximately 2.11 x 10^(-8) meters, and the number of stable nuclei is approximately 1.64 x 10^21 nuclei/m^3.
Learn more about homogeneous nucleation here:
https://brainly.com/question/31966477
#SPJ11
A 1.0 m^3 rigid container water vapor at initial state of 1Mpa and 300C . the tank has one outlet the system is now heated and some of the steam was allowed to leave the container in way that the pressure is controlled to remain constant during this process The process was stopped when the temperature inside the container reached 400C Determine the amount of heat added during this process
The amount of heat added during the process is approximately 727.86 kJ.
The amount of heat added during the process can be determined using the following formula:
Q = m × Cp × ΔT,
where Q is the heat added,
m is the mass of the substance,
Cp is the specific heat capacity of the substance, and
ΔT is the change in temperature.
To calculate the mass of the substance, we can use the ideal gas law:P × V = n × R × T,
where P is the pressure, V is the volume, n is the number of moles of the substance, R is the gas constant, and T is the temperature.
Rearranging this equation, we get:n = P × V / R × T
Substituting the given values:
P = 1 MPa = 10^6 Pa
V = 1 m^3
R = 8.314 J/mol·K
T1 = 300 C = 573 K, and
T2 = 400 C = 673 K,
n = (10^6 Pa × 1 m^3) / (8.314 J/mol·K × 573 K)
= 214.97 moles of water vapor
The mass of the water vapor can be calculated using its molar mass:
MM = 18.02 g/molm
= n × MM
= 214.97 moles × 18.02 g/mol
= 3875.8 g
= 3.8758 kg
The specific heat capacity of water vapor can be found in a table:Cp = 1.872 J/g·K
Using the formula above, the heat added during the process is:
Q = m × Cp × ΔT
= 3.8758 kg × 1.872 J/g·K × (400 C - 300 C)
= 727,862.784 J or 727.86 kJ
Therefore, the amount of heat added during the process is approximately 727.86 kJ.
learn more about heat from given link
https://brainly.com/question/21927103
#SPJ11
an 8-ohm resistance connected to a battery with internal resistance draws 1.6 ampere and if a 30-ohm resistance is connected to the same baterry if draws 0.5 ampere.what is current drawn by 6 ohm resistances from the baterry
If an 8-ohm resistance connected to a battery with internal resistance draws 1.6 ampere. The current drawn by the 6-ohm resistor from the battery is 2.67 amperes.
What is the current drawn?Using Ohm's law for the first case:
1.6 A = V / (r + 8 Ω)
Using Ohm's law for the second case:
0.5 A = V / (r + 30 Ω)
Let's solve the equations:
From the first equation: V = (1.6 A) * (r + 8 Ω)
From the second equation: V = (0.5 A) * (r + 30 Ω)
So,
(1.6 A) * (r + 8 Ω) = (0.5 A) * (r + 30 Ω)
Let's solve for r:
1.6r + 12.8 = 0.5r + 15
1.6r - 0.5r = 15 - 12.8
1.1r = 2.2
r = 2.2 / 1.1
r = 2 Ω
Let calculate the voltage (V) by substituting it into one of the original equations.
1.6 A = V / (2 Ω + 8 Ω)
1.6 A = V / 10 Ω
V = (1.6 A) * (10 Ω)
V = 16 V
Let calculate the current drawn by the 6-ohm resistor using Ohm's law:
I = V / R
I = 16 V / 6 Ω
I ≈ 2.67 A
Therefore, the current drawn by the 6-ohm resistor from the battery is 2.67 amperes.
Learn more about current here:https://brainly.com/question/1100341
#SPJ1
a 2kg object slides on a horizontal surface with an initial velocity of 3 m/s starting from the origin. what is the distance travelled by the object as it stops if the coefficient of friction of the surface is 0.5
The object will travel a distance of 4.5 meters before coming to a stop.
When an object slides on a horizontal surface, the opposing force that acts against its motion is the force of friction. The magnitude of the frictional force can be determined using the equation:
Frictional force = coefficient of friction × normal force
The normal force is the force exerted by the surface on the object, which is equal to the object's weight when it is on a horizontal surface. The weight can be calculated by multiplying the mass of the object (2 kg) by the acceleration due to gravity (9.8 m/s^2):
Weight = mass × acceleration due to gravity = 2 kg × 9.8 m/s^2 = 19.6 N
Therefore, the normal force acting on the object is 19.6 N.
The frictional force opposing the motion of the object can be calculated as:
Frictional force = 0.5 × 19.6 N = 9.8 N
The frictional force acts in the opposite direction to the motion of the object, causing it to decelerate. The deceleration can be determined using Newton's second law of motion:
Force = mass × acceleration
Rearranging the equation, we have:
Acceleration = Force / mass = 9.8 N / 2 kg = 4.9 m/s^2
The negative sign indicates that the acceleration is in the opposite direction to the initial velocity.
To find the distance traveled, we can use the kinematic equation:
Final velocity^2 = Initial velocity^2 + 2 × acceleration × distance
Since the object comes to a stop, the final velocity is 0 m/s. Plugging in the given values:
0^2 = 3^2 + 2 × (-4.9 m/s^2) × distance
Simplifying the equation:
9 = 2 × 4.9 m/s^2 × distance
Dividing both sides by 9.8 m/s^2:
distance = 9 / (2 × 4.9 m/s^2) = 0.9184 m
Therefore, the object will travel a distance of approximately 0.9184 meters, or 4.5 meters, before coming to a stop.
Learn more about Coefficient of friction
brainly.com/question/29281540
#SPJ11
A rotary lever with a length of \( 0.23 \mathrm{~m} \) rotates \( 20 .^{\circ} \) when a force of \( 296 \mathrm{~N} \) is applied to it. What is the maximum possible work this lever can do in newton-
The maximum possible work that can be done by the rotary lever is approximately 61.35 newton-meters.
The maximum possible work that can be done by the rotary lever can be calculated using the formula: work = force × distance × cosine(angle). Given the length of the lever, the applied force, and the angle of rotation, we can determine the maximum work done in newton-meters.
To calculate the maximum possible work done by the rotary lever, we use the formula: work = force × distance × cosine(angle), where force is the applied force, distance is the length of the lever, and angle is the angle of rotation.
Given:
Length of the lever (distance) = 0.23 m
Applied force = 296 N
Angle of rotation = 20 degrees
First, we convert the angle from degrees to radians:
angle (in radians) = angle (in degrees) × π / 180
angle (in radians) = 20° × π / 180 ≈ 0.3491 radians
Next, we calculate the maximum work done:
work = 296 N × 0.23 m × cosine(0.3491 radians)
Using a calculator, we evaluate cosine(0.3491 radians) ≈ 0.9397, and substitute the values into the formula:
work ≈ 296 N × 0.23 m × 0.9397
Calculating the result:
work ≈ 61.35 N·m
Therefore, the maximum possible work that can be done by the rotary lever is approximately 61.35 newton-meters.
Learn more about lever here:
https://brainly.com/question/31378631
#SPJ11
The temperature coefficient of resistivity for copper is 0.0068^∘C ^−1
, If a copper wire has a resistance of 104.0Ω at 20.0 " C, what is its resistance (in
The resistance of the wire at 72.5°C will be 141.12Ω
Coefficient of resistivity for copper = 0.0068^∘C ^−1
Resistance at a temperature = 104 Ω
Temperature = 20°C
The given question is a case of temperature-dependent resistance, the property which determines the resistance offered by various materials, and their ranges in case of an increase or decrease in temperature. This is because of the unique properties of every element.
Calculating the value of resistance at a given temperature -
Rₙ = R₀(1 + α(Tₙ-T₀))
Substituting the values -
Rₙ = 104(1 + 0.0068(72.5 - 20))
= 104 (1 + 0.357)
= 104*1.357
= 141.12 Ω
Read more about resistance on:
https://brainly.com/question/28135236
#SPJ4
The force of gravity on an object is proportional to the
object’s mass, yet all objects
fall with the same gravitational acceleration. Why?
Please write the answer neatly.
The force of gravity on an object is proportional to its mass. However, all objects fall with the same gravitational acceleration. This is because the gravitational force that causes objects to fall is also proportional to the object's weight, not just its mass.
This gravitational force is constant for all objects on Earth because Earth's gravitational field is uniform.How the force of gravity on an object is proportional to its mass and why all objects fall with the same gravitational acceleration is discussed in the following paragraphs:According to Newton's law of gravitation, the gravitational force between two objects is proportional to the product of their masses and inversely proportional to the square of the distance between them. This formula can be written as:F = G(m1m2/r^2)Where F is the force of gravity, m1 and m2 are the masses of the two objects, r is the distance between them, and G is the gravitational constant. This law states that the greater the mass of an object, the greater the gravitational force it experiences. However, it also means that the greater the distance between two objects, the weaker the gravitational force between them. For this reason, the gravitational force on an object is greater when it is closer to Earth than when it is further away.When an object is dropped, the force of gravity pulls it toward Earth. As the object falls, it gains speed and momentum, which causes its weight to increase. This increase in weight causes an increase in the gravitational force, which in turn causes the object to fall faster. However, the acceleration due to gravity is constant for all objects on Earth, regardless of their mass or weight. This acceleration is denoted by the letter g and is approximately equal to 9.8 meters per second squared (9.8 m/s^2) at sea level.What this means is that all objects on Earth will fall with the same gravitational acceleration, regardless of their mass or weight. The reason for this is that the gravitational force that causes objects to fall is also proportional to the object's weight, not just its mass. This gravitational force is constant for all objects on Earth because Earth's gravitational field is uniform. Thus, the force of gravity on an object is proportional to its mass, but all objects fall with the same gravitational acceleration due to the uniformity of Earth's gravitational field.
To Learn more about proportional Click this!
brainly.com/question/33490579
#SPJ11
(io) A stone is dropped into a river from a bridge 43.9 m above the water. Another stone is thrown vertically down 1.00 s after the first is dropped. The stones strike the water at the same time. (a) What is the initial speed of the second stone?
The initial speed of the second stone is 38.95 m/s The height of the bridge, h = 43.9 m. Let the initial velocity of the second stone be u2.
The time taken by the first stone to hit the water from the bridge is given by:t1 = √(2h/g) Where g is the acceleration due to gravity.
Therefore, the time taken by the first stone to hit the water is:t1 = √(2h/g) = √(2×43.9/9.8) = 2.01 s.
Time taken by the second stone to hit the water is given by:t2 = t1 - 1 = 2.01 - 1 = 1.01 s.
Using the kinematic equation, we have:h = u2t + (1/2)gt² where h is the height of the bridge, t is the time taken by the second stone to hit the water, and g is the acceleration due to gravity.
Solving for u2, we get:u2 = (h - (1/2)gt²)/t= (43.9 - (1/2)×9.8×(1.01)²)/1.01= 43.9 - 4.95= 38.95 m/s.
Therefore, the initial speed of the second stone is 38.95 m/s.
Learn more about acceleration here ;
https://brainly.com/question/2303856
#SPJ11
Two 1.20 mm nonconducting rods meet at a right angle. One rod carries +1.70 μC of charge distributed uniformly along its length, and the other carries -1.70 μC distributed uniformly along it (Figure 1).
Find the magnitude of the electric field these rods produce at point PP, which is 60.0 cm from each rod. Express your answer with the appropriate units.
Find the direction angle of the electric field from part A. The angle is measured from the +x-axis toward the +y-axis. Express your answer in degrees.
To find the direction angle of the electric field, we can use trigonometry. Since the rods meet at a right angle, the direction angle will be 45 degrees.
To find the magnitude of the electric field produced by the rods at point P, we can use the principle of superposition. The electric field at P due to each rod can be calculated separately and then summed.
Considering each rod individually, we can use the equation for the electric field produced by a uniformly charged rod at a point on its perpendicular bisector:
Electric field (E1) produced by the positive rod = (k * Q1) / [tex](L1 * sqrt((L1/2)^2 + d^2))[/tex]
Electric field (E2) produced by the negative rod = (k * Q2) / (L2 * sqrt[tex]((L2/2)^2 + d^2))[/tex]
where k is the Coulomb's constant, Q1 and Q2 are the charges on the rods, L1 and L2 are the lengths of the rods, and d is the distance from the midpoint of each rod to point P.
Since the rods are nonconducting and have opposite charges, the magnitudes of their charges are equal: |Q1| = |Q2| = 1.70 μC.
Substituting the given values, the equation becomes:
Electric field (E1) = [tex](9 * 10^9 N*m^2/C^2 * 1.70 * 10^-6 C) / (1.20 * 10^-3 m * sqrt((1.20 * 10^-3 m/2)^2 + (0.60 m)^2))[/tex]
Electric field (E2) = [tex](9 * 10^9 N*m^2/C^2 * 1.70 * 10^-6 C) / (1.20 * 10^-3 m * sqrt((1.20 * 10^-3 m/2)^2 + (0.60 m)^2))[/tex]
Calculate these expressions to find the electric fields (E1 and E2) produced by the rods. Then, add the magnitudes of these electric fields to obtain the total electric field at point P.
To know more about electric field refer to-
https://brainly.com/question/11482745
#SPJ11
: An Atwood machine consists of two masses, mA = 62 kg and mg = 75 kg. connected by a massless inelastic cord that passes over a pulley free to rotate (Figure 1). The pulley is a solid cylinder of radius R=0.45 m and mass 7.0 kg. (Hint: The tensions FTA and Fre are not equal.] Part A Determine the acceleration of each mass. Express your answer to two significant figures and include the appropriate units.
In an Atwood machine with masses mA = 62 kg and mg = 75 kg, connected by a massless inelastic cord over a pulley, the acceleration of each mass can be determined. The pulley is a solid cylinder with a radius of R = 0.45 m and a mass of 7.0 kg. It should be noted that the tensions in the cord on each side of the pulley are not equal.
To determine the acceleration of each mass in the Atwood machine, we can use the principles of Newton's second law and the conservation of energy. Let's denote the tension in the cord on the side of mass mA as FTA and the tension on the side of mass mg as FTg.
1. Find the acceleration using Newton's second law:
Since the pulley is free to rotate, we need to consider the torques acting on it. The net torque on the pulley is equal to the moment of inertia times the angular acceleration.
τnet = Iα
The moment of inertia of a solid cylinder about its axis of rotation is given by I = (1/2)MR², where M is the mass of the pulley and R is its radius.
τnet = (1/2)MR²α
The tension in the cord on the side of mass mA produces a torque that rotates the pulley counterclockwise, while the tension on the side of mass mg produces a torque that rotates the pulley clockwise.
τnet = FTA * R - FTg * R
Since the pulley is not accelerating in the angular direction, the net torque is zero.
0 = FTA * R - FTg * R
From this equation, we can conclude that FTA is not equal to FTg.
Now, consider the forces acting on each mass:
mA * g - FTA = mA * a
FTg - mg * g = mg * a
Solving these two equations simultaneously, we can find the acceleration (a) of each mass.
2. Find the acceleration using conservation of energy:
Another approach is to consider the conservation of energy. The change in gravitational potential energy of mass mA is converted into the rotational kinetic energy of the pulley and the translational kinetic energy of mass mg.
ΔPE = ΔKEpulley + ΔKEmg
The change in gravitational potential energy is given by:
ΔPE = (mA * g - FTA) * h
The change in kinetic energy for the pulley can be calculated using the moment of inertia (I) and the angular speed (ω):
ΔKEpulley = (1/2)Iω²
The change in kinetic energy for mass mg can be calculated using its mass (mg) and acceleration (a):
ΔKEmg = (1/2)mg * a²
By equating these energy changes, we can solve for the acceleration (a).
Both methods should yield the same result for the acceleration of each mass.
To know more about acceleration click here:
https://brainly.com/question/12550364
#SPJ11
A school bus is traveling at a speed of 0.4 cm/s. School children on the bus and on the sidewalk are both attempting to measure the time it takes for the bus to travel one city block by timing the times the bus enters and leaves the city block. According to school children on the bus, it takes 6 s. How long does it take according to school children on the sidewalk? 6.547 s 6.124 s 6.290 s 6.928 s An AC source has a maximum voltage of 170 V and a frequency of 60 Hz. A capacitor circuit using this AC source and a capacitor of 5×10−6 F has a maximum current of 0.320 A. 0.192 A 0.128 A 0.256 A
1. According to school children on the sidewalk, it takes 6.547 seconds for the school bus to travel one city block. Therefore the correct option is a) 6.547 s.
2. The capacitor circuit with the AC source and a capacitor of 5×10^(-6) F has a maximum current of 0.032 A. Therefore the correct option is a) 0.320 A.
When the school children on the bus measure the time it takes for the bus to travel one city block, they experience time dilation due to their relative motion. This means that the time they measure will be shorter compared to an observer at rest, such as the school children on the sidewalk.
Since the children on the bus measure the time as 6 seconds, we need to account for the time dilation effect to find the time according to the children on the sidewalk. We can use the concept of time dilation in special relativity to calculate the time experienced by the stationary observers.
The time dilation factor can be calculated using the formula:
time dilation factor = 1 / √(1 - (v²/c²))
where v is the velocity of the bus (0.4 cm/s) and c is the speed of light (approximately 3 × 10^8 m/s).
Plugging in the values, we get:
time dilation factor = 1 / √(1 - (0.4^2 / (3 × 10^8)^2))
Calculating this expression, we find that the time dilation factor is approximately 1.000090014. Therefore, the time experienced by the children on the sidewalk is the time measured on the bus multiplied by the time dilation factor.
6 seconds * 1.000090014 ≈ 6.547 seconds
Hence, the correct answer is that according to school children on the sidewalk, it takes 6.547 seconds for the bus to travel one city block.
Now, moving on to the second part of the question regarding the capacitor circuit with an AC source and a capacitor:
A) The capacitor circuit with the AC source and a capacitor of 5×10^(-6) F has a maximum current of 0.128 A.
In an AC circuit with a capacitor, the current leads the voltage by 90 degrees. The maximum current can be determined using the formula:
maximum current = (maximum voltage) / (capacitive reactance)
where the capacitive reactance is given by:
capacitive reactance = 1 / (2πfC)
where f is the frequency of the AC source and C is the capacitance.
Plugging in the values, we get:
capacitive reactance = 1 / (2π(60)(5×10^(-6))) ≈ 5305.79 ohms
Now, we can calculate the maximum current:
maximum current = (170 V) / (5305.79 ohms) ≈ 0.032 A
Hence, the correct answer is that the capacitor circuit with the AC source and a capacitor of 5×10^(-6) F has a maximum current of 0.032 A.
To know more about capacitor click here:
https://brainly.com/question/31627158
#SPJ11
A baseball is thrown vertically into the air. The acceleration of the ball at its highest point is: zero 8. down 2 g . down 2 g . up
When the baseball is thrown vertically into the air, its acceleration at the highest point is zero.
At the highest point of its trajectory, the baseball momentarily reaches its maximum height and starts to descend. At this point, its velocity is zero because it has stopped momentarily.
Acceleration is defined as the rate of change of velocity. Since the velocity is momentarily zero at the highest point, there is no change in velocity, and thus the acceleration is zero.
The force of gravity acts downward on the baseball, but at the highest point, the acceleration due to gravity is counteracted by the deceleration from the upward initial velocity until it comes to a stop, resulting in an acceleration of zero at the highest point.
To know more about acceleration refer to-
https://brainly.com/question/2303856
#SPJ11
Complete question
A baseball is thrown vertically into the air. The acceleration of the ball at its highest point is
An orifice plate with diameter 10 cm inserted in a pipe of 20 cm diameter. Pressure difference is measured by Hg differential manometer on two sides of the orifice plate gives reading 50 cm of Hg. Find the fluid flow rate. Coefficient of discharge Ca=0.64 and specific gravity of fluid is 0.90. (density of mercury is 13.6 g/cm³)
Given data:Diameter of orifice plate = 10 cm = 0.1 of pipe = 20 cm = 0.2 mPressure difference = 50 cm of Hg
Coefficient of discharge, C_a = 0.64Specific of fluid
SG = 0.9Density of mercury
ρ_m = 13.6 g/cm³ = 13600 kg/m³
We need to find the fluid flow rate.
From Bernoulli's principle of fluid flow, the difference, ∆P between the two points in a flow is related to the flow rate, Q by the formula:
∆P = KQ²where K is a constant for a given flow system known as the coefficient of discharge.
Now, the area of the orifice plate is given by:
[tex]A = π/4 × d² = π/4 × (0.1)² = 0.00785 m²[/tex]
The area of the pipe is given by:
[tex]A' = π/4 × d'² = π/4 × (0.2)² = 0.0314 m²[/tex]
Now, the flow rate is given by:
[tex]Q = A√(2g∆h/ρ)(C_a/C_c)[/tex]
Where g is the acceleration due to gravity and ∆h is the difference in the levels of the mercury in the two legs of the differential manometer.g = 9.8 m/s²∆h = 50 cm of Hg =50/100 m of Hg = 0.5 m of Hg
Now, to convert the pressure of mercury to the equivalent fluid pressure, we use the formula:
P = ρghwhere P is the pressure,
ρ is the density, g is the acceleration due to gravity and h is the height of the fluid column.
[tex]P_m = ρ_mgh_m = 13600 × 9.8 × 0.5 = 66640 N/m²[/tex]
The fluid pressure is half the mercury pressure, therefore:
[tex]P = P_m/2 = 66640/2 = 33320 N/m²[/tex]
Substituting the given values in the formula for Q, we get:
[tex]Q = 0.00785√(2 × 9.8 × 0.5/1000 × 33320)(0.64/C_c)C_[/tex]
c is the coefficient of contraction of the orifice plate which is assumed to be 0.6 for a standard orifice plate.
The value of Q can be calculated as follows:
Q = 0.0269 m³/
The fluid flow rate is 0.0269 m³/s.33518187
To know more about Diameter visit:
https://brainly.com/question/32968193
#SPJ11
Which of these best defines mass? A. the amount of space occupied by an object B. the distance between two points C. the quantity of matter in an object D. the interval between two events
The best defines mass is A. the measure of the amount of matter an object has.
The term is a fundamental concept in physics and is typically measured in kilograms. The amount of matter that an object has remains constant regardless of the location of the object. Mass is a scalar quantity and can never be negative. A mass that is moving is referred to as kinetic energy, it's also defined as a measurement of resistance to acceleration by a force. When the mass of an object is greater, it requires more force to move it.
On the other hand, if an object's mass is lower, it requires less force to move it. The concept of mass is important in various fields such as engineering, physics, and chemistry, and it's critical in explaining the fundamental principles of the universe. Hence, mass can be defined as A. the quantity of matter present in an object.
Learn more about mass at:
https://brainly.com/question/30282435
#SPJ11
when checking the electrical circuits of an air-conditioning system, each parallel circuit should be isolated and checked separately.
When checking the electrical circuits of an air-conditioning system, it is important to isolate and check each parallel circuit separately for several reasons.
Firstly, parallel circuits in an air-conditioning system have multiple branches where electrical current can flow independently. By isolating each parallel circuit, it allows for a focused examination of the specific components and connections within that circuit. This approach helps in identifying and troubleshooting any faults or malfunctions that may be specific to that particular circuit.
Secondly, isolating parallel circuits minimizes the potential for interference or cross-talk between circuits. If all the circuits were tested simultaneously, any issues in one circuit could affect the measurements or readings in the others, leading to confusion and inaccurate diagnoses.
Moreover, isolating parallel circuits allows for a systematic and organized approach to troubleshooting. By addressing one circuit at a time, it becomes easier to track the flow of current, identify faulty components, and pinpoint the root cause of any electrical issues. It helps in streamlining the diagnostic process and saves time by narrowing down the areas of concern.
Overall, isolating and checking each parallel circuit separately in an air-conditioning system ensures a comprehensive and accurate assessment of the electrical components, promoting efficient troubleshooting and effective repairs.
Learn more about parallel circuits here:
https://brainly.com/question/33233582
#SPJ11
One end of a spring is attached to a wall and the other end is attached to a block of mass 3.55 kg. The spring has a spring constant of 72.7 N/m. The entire assembly rests on a frictionless surface.
If the spring/block assembly is compressed (block is pushed to the left) by 27.8 cm, what is the acceleration of the block at the instant it is released after the compression? (In this case, you may neglect the mass of the spring itself.) Report your answer in m/s2.
The acceleration of the block at the instant it is released after the compression is approximately -5.69 m/[tex]s^2[/tex] by using Hooke's Law and Newton's Second Law of Motion.
To determine the acceleration of the block when it is released after compression, we can use Hooke's Law and Newton's Second Law of Motion.
Hooke's Law states that the force exerted by a spring is directly proportional to the displacement from its equilibrium position. Mathematically, this can be represented as:
F = -kx
Where F is the force exerted by the spring, k is the spring constant, and x is the displacement from the equilibrium position.
In this case, the spring is compressed by 27.8 cm (or 0.278 m) to the left. The force exerted by the spring can be calculated as:
F = -kx = -(72.7 N/m)(0.278 m) = -20.1856 N
Since the spring is attached to a block of mass 3.55 kg, this force will cause the block to accelerate. According to Newton's Second Law of Motion, the acceleration (a) of an object is related to the net force ([tex]F_{net[/tex]) acting on it and its mass (m) by the equation:
[tex]F_{net[/tex] = ma
In this case, the net force acting on the block is the force exerted by the spring. Therefore:
[tex]F_{net[/tex] = -20.1856 N
Plugging in the values, we have:
-20.1856 N = (3.55 kg) * a
Solving for acceleration (a):
a = -20.1856 N / 3.55 kg ≈ -5.69 m/[tex]s^2[/tex]
The negative sign indicates that the acceleration is in the opposite direction of the compression, so the block accelerates to the right.
Therefore, the acceleration of the block at the instant it is released after the compression is approximately -5.69 m/[tex]s^2.[/tex]
Learn more about Hooke's Law
https://brainly.com/question/29296378
#SPJ11
A 12.10μC point charge is sitting at the origin. Part A What is the radial distance between the 500 V equipotential surface and the 1000 V surface? Express your answer with the appropriate units. Part B What is the distance between the 1000 V surface and the 1500 V surface? Express your answer in meters to three significant figures.
The distance between the 1000 V surface and the 1500 V surface is 36.14 m. A 12.10 μC point charge is sitting at the origin. The radial distance between the 500 V equipotential surface and the 1000 V surface and the distance between the 1000 V surface and the 1500 V surface.
The electric potential at a distance r from a point charge Q is given by the formula:V=kQ/r where k is the Coulomb constant and is equal to 9.0 x 109 Nm2/C2.
For the equipotential surface where the potential is V, the radius r of the surface is given by:r = kQ/V.
The radial distance between two equipotential surfaces is the difference in the radii.
Let the radius of the 500 V surface be r1 and the radius of the 1000 V surface be r2.
The radial distance between these two surfaces is:r2 - r1 = kQ/1000 - kQ/500 = kQ/1000 x (1/2) = kQ/2000 = (9.0 x 109 Nm2/C2)(12.10 μC)/(2000 V) = 54.45 m.
So, the radial distance between the 500 V equipotential surface and the 1000 V surface is 54.45 m.
Let the radius of the 1500 V surface be r3.
The distance between the 1000 V surface and the 1500 V surface is:r3 - r2 = kQ/1500 - kQ/1000 = kQ/3000 = (9.0 x 109 Nm2/C2)(12.10 μC)/(3000 V) = 36.14 m.
So, the distance between the 1000 V surface and the 1500 V surface is 36.14 m.
Learn more about electric potential here ;
https://brainly.com/question/28444459
#SPJ11
A uniform flat plate of metal is situated in the reference frame shown in the figure below. Assume the mass is uniformly distributed If the mass of the plate is 3 kg calculate the moment of inertia around the y-axis. Use equation #2 I=∫R
2
dm
To calculate the moment of inertia (I) around the y-axis for the given plate, we'll integrate the expression for the moment of inertia (I = ∫R^2 dm) using the provided data. First, let's evaluate dm and substitute it into the equation.
Since the mass is uniformly distributed, dm is proportional to the area of the elemental strip at a distance r from the y-axis and an angle θ from the horizontal. The area of the strip (dA) is given by dA = rh dθ, where σ is the mass per unit area of the plate.
Integrating dm with the limits of r and θ, we have:
∫dm = ∫(0 to R)∫(-h/2 to h/2) dm dθ dr
∫dm = ∫(0 to R)∫(-h/2 to h/2) σ rh dθ dr
∫dm = ∫(0 to R)σ r^2 h dθ dr
Substituting the given data:
Area of the plate = L x W = 4 x 1 = 4 m^2
Density of the plate = σ = mass/area = 3/4 = 0.75 kg/m^2
Height of the plate = h = 0.02 m
We are given R = 2 m.
∫dm = 0.75 × 0.02 × 2π ∫(0 to 2) r^2 dr
∫dm = 0.009π [r^3/3] (0 to 2)
∫dm = 0.009π (8/3)
Therefore, ∫dm = 0.2010642... ≈ 0.20 (approximated to 2 decimal places).
Hence, the moment of inertia around the y-axis for the given plate is approximately 0.20 units.
To Learn more about evaluate Click this!
brainly.com/question/17284520
#SPJ11
which of the following is not a vector? velocity weight friction density
Among the options provided, density is not a vector. Velocity, weight, and friction are vector quantities because they have both magnitude and direction. Density, on the other hand, is a scalar quantity that only has magnitude and does not have a specific direction associated with it.
A vector is a quantity that has both magnitude and direction. Velocity, weight, and friction are all examples of vector quantities.
Velocity is the rate of change of displacement and has both magnitude (speed) and direction (e.g., 20 m/s north). Weight is the force experienced by an object due to gravity and has both magnitude (e.g., 50 N) and direction (downward, towards the center of the Earth). Friction is the force that opposes the motion of an object and also has both magnitude and direction (e.g., 10 N opposite to the direction of motion).
On the other hand, density is a scalar quantity that describes the amount of mass per unit volume. It is a scalar because it only has magnitude and does not have a specific direction associated with it. For example, the density of a substance can be expressed as 1 g/cm³ without any indication of direction.
Learn more about vector quantity here:
brainly.com/question/32869238
#SPJ11
(a) Calculate the classical momentum of a neutron traveling at 0.976c, neglecting relativistic effects. (Use 1.67 x 10-27 for the mass of the neutron.) kg. m/s (b) Repeat the calculation while including relativistic effects. kg. m/s (c) Does it make sense to neglect relativity at such speeds? O yes O no
(a) The classical momentum of a neutron traveling at 0.976c, neglecting relativistic effects, can be calculated using the classical momentum equation:
momentum = mass × velocity.
The mass of the neutron is given as [tex]1.67 \times 10^{-27}[/tex] kg, and the velocity is 0.976c.
(b) To include relativistic effects, we need to use the relativistic momentum equation:
momentum = [tex]\frac{( m \times v)}{\sqrt[2]{1-\frac{v^{2} }{c^{2} } } }[/tex].
(c) It does not make sense to neglect relativity at such speeds because relativistic effects become significant as the speed approaches the speed of light.
Now,
(a) The classical momentum can be calculated as follows:
momentum = mass × velocity = [tex][1.67 \times 10^{-27}] \times 0.976c = 1.63 \times 10^{-27}[/tex]
(b) To include relativistic effects, we use the relativistic momentum equation:
momentum = [tex]\frac{( m \times v)}{\sqrt[2]{\frac{v^{2} }{c^{2} } } }[/tex]
= [tex]\frac{( [1.67 \times 10^{-27} ] \times 0.976c)}{\sqrt[2]{1-\frac{(0.976c)^{2} }{299792458^{2} } } }[/tex]
≈ [tex]2.43 \times 10^{-21}[/tex] kg·m/s.
(c) It does not make sense to neglect relativity at such speeds because as the velocity approaches the speed of light, relativistic effects become significant. The relativistic momentum takes into account the increase in mass and the decrease in velocity as the speed approaches c, providing a more accurate description of the momentum of the neutron. Neglecting relativity would result in an incorrect estimation of the neutron's momentum at relativistic speeds.
Learn more about momentum at:
https://brainly.com/question/30677308
#SPJ11
How does the stream gradient affect its velocity? The steeper the gradient, the lower the velocity The steeper the gradient, the higher the velocity There is no significant relationship between the gradient and the velocity of a stream How does the stream width affect its velocity? The largest the width, the lower the velocity The largest the width, the higher the velocity There is no significant relationship between the width and the velocity of a stream. Floods usually occur when precipitation falls slower than that water can be absorbed into the ground or carried away by rivers or streams. True False Question 17 (2 points) Select the correct statement in this list Heavily vegetated lands are less likely to experience flooding Heavily vegetated lands are more likely to experience flooding Wetlands play a key role in increasing the impacts of floods, by acting as a buffer between land and high water levels.
1. The correct answer is b. The steeper the gradient, the higher the velocity. The stream gradient refers to the change in elevation of a stream over a certain distance. When the gradient of a stream is steeper, it means that the stream has a greater change in elevation per unit of distance. This steepness creates a greater gravitational force, causing the water to flow faster downstream. Therefore, a higher stream gradient is associated with a higher velocity of the stream.
2. The correct answer is b. The larger the width, the higher the velocity. Stream width refers to the horizontal distance across the stream channel. When a stream has a larger width, it means that there is a greater cross-sectional area for the water to flow through. As a result, the water has more space to move, leading to increased velocity. This is due to the conservation of mass principle, where a larger width allows for a higher volume of water to pass through, resulting in a higher velocity.
3. The correct answer is b. False. Floods usually occur when precipitation falls faster than water can be absorbed into the ground or carried away by rivers or streams. When there is heavy or prolonged rainfall, the rate of precipitation exceeds the rate at which the ground can absorb the water or the rivers and streams can carry it away. As a result, the excess water accumulates on the surface, leading to flooding. It is important to note that flooding can also occur due to other factors such as dam failures, snowmelt, or tidal surges.
4. The correct answer is a. Heavily vegetated lands are less likely to experience flooding. Vegetation, especially trees and plants with extensive root systems, can help reduce the risk of flooding. The roots of vegetation act as natural barriers and can absorb a significant amount of water from the soil, reducing the amount of runoff into streams and rivers. Additionally, vegetation helps to stabilize the soil, preventing erosion and maintaining the capacity of water absorption. Therefore, heavily vegetated lands serve as a protective measure against flooding by slowing down the flow of water and increasing the water retention capacity of the soil.
To learn more about velocity, Visit:
https://brainly.com/question/80295
#SPJ11
The correct format of the question should be:
1. How does the stream gradient affect its velocity?
a. The steeper the gradient, the lower the velocity
b. The steeper the gradient, the higher the velocity
c. There is no significant relationship between the gradient and the velocity of a stream
2. How does the stream width affect its velocity?
a. The largest the width, the lower the velocity
b. The largest the width, the higher the velocity
c. There is no significant relationship between the width and the velocity of a stream.
3. Floods usually occur when precipitation falls slower than that water can be absorbed into the ground or carried away by rivers or streams.
a. True
b. False
4. Select the correct statement in this list
a. Heavily vegetated lands are less likely to experience flooding
b. Heavily vegetated lands are more likely to experience flooding
c. Wetlands play a key role in increasing the impacts of floods, by acting as a buffer between land and high water levels.
The slits in a piece of paper are separated by a distance of 48.0 × 10-6 m and a laser is shined through the slits. [10 points ] a. The second order maximum appears on a screen at an angle of 0.0990°. What is the wavelength of the light used in the experiment in nanometers? [ 4 points ] b. If the distance between the slits is increased, but the second order maximum stays in the same place, the wavelength of light also had to have changed. Did it increase or decrease? Explain your answer. [ 2 points] c. If the slit distance is changed to 68.0× 106 m, what is the wavelength of the light (in nm) if the second order maximum is in the same location on the screen. [ 4 points ]
According to the given problem, the second-order maximum appears at an angle of 0.0990° and the distance between the slits is 48.0 × 10-6 m.
By using the formula for fringe spacing, d sinθ = mλ, where d is the distance between the slits, θ is the angle of diffraction, m is the order of the maximum, and λ is the wavelength of light, we can find the wavelength of light to be 311 nm.
If the distance between the slits is increased while the second-order maximum remains in the same position, the wavelength of light would decrease.
When the distance between the slits is changed to 68.0 × 10^6 m and the second-order maximum remains in the same location, the wavelength of light is calculated to be 391 nm.
Read more about wavelength of light
https://brainly.com/question/32186466
#SPJ11
A slender rod of length l and weight 100 N is pivoted at one end as shown. It is released from rest in a horizontal position and swings freely. Assuming there is no friction and air resistance.
I
ˉ
=
12
1
ml
2
(a) Show that using conservation of energy method (T
1
+V
1
=T
2
+V
2
) and Principle of work and energy (T
1
+u
1→2
=T
2
) give us the same equation. (5pts) (b) Solve the equation found in part (a) to determine the angular velocity of the rod as it passes through a vertical position in terms of g and L(10pts) (c) If m=10 kg,l=2m and g=10m/s
2
find the value of angular velocity (5pts) (d) determine the corresponding reaction at the pivot in terms of m and g and then find the value of that.
(a) We assume that at the initial point, the rod is at rest and the height is zero, which means the potential energy of the rod is zero. The initial kinetic energy of the rod is also zero.
When it reaches the lowest point, the potential energy of the rod is zero. So, the sum of kinetic energy and potential energy is equal to each other.
So, we have,
T1+V1 = T2+V2
Where,
T1=0
T2 =0
V1 =mgh
V2 =0
∴ 0+ mg
h = 0 + (1/2)
I ω2 ........(1)
(Here I= ml2/12. Because, the rod is pivoted at one end so its moment of inertia about that point is ml2/3. But we need moment of inertia about its center of mass, which is ml2/12)
Also, using work-energy principle,
T1 + u 1→2
= T2=0+ mg
L= 1/2Iω2
∴ mgL= 1/2
Iω2 ........(2)
From equations (1) and (2), we have
mg
h = 1/2
Iω2 => g
h = (1/2) l (ml2/12) (ω)
2 => 2gh
/ l = ω2 (ml2/12) =>
ω2 = (24gh/ ml).
(b) We have,ω2 = (24gh/ ml)
Substituting given values, ω2 = 120/2 = 60 rad/s.
So, the angular velocity of the rod as it passes through a vertical position in terms of g and L is 60 rad/s.
(c) Here, m= 10 kg,l=2m and g=10m/s2.
Using equation from part (b),ω2 = (24gh/ ml) => 60 = (24 × 10 × h)/(10 × 2) => h = 5 m.
(d) When the rod passes through a vertical position, it becomes horizontal. At that moment, the reaction at the pivot will be equal to the weight of the rod which is 100 N.
Answer:
(a) T1+V1 = T2+V2 => mgh = 1/2Iω2 and mgL= 1/2Iω2
(b) The angular velocity of the rod as it passes through a vertical position in terms of g and L is 60 rad/s.
(c) Here, m= 10 kg,l=2m and g=10m/s2.
The angular velocity of the rod as it passes through a vertical position in terms of g and L is 60 rad/s.
(d) The reaction at the pivot will be equal to the weight of the rod which is 100 N.
To know more about initial visit :
https://brainly.com/question/32209767
#SPJ11
A 12-lb weight is suspended from a spring with a spring constant of 4 lb/in. What is the natural frequency of the system? 4. A 20-lb weight as period of 0.18 seconds. What is the spring constant of the system?
A 12-lb weight is suspended from a spring with a spring constant of 4 lb/in.
What is the natural frequency of the system?
Given,
Mass of weight (m) = 12 lb
Spring constant (k) = 4 lb/in
Formula used
Natural frequency (ω) = `sqrt(k/m)
`Solution
Natural frequency (ω) = `sqrt(k/m)` = `sqrt(4/12)` = 0.577 rad/s
Natural frequency (f) = `ω/(2π)` = `0.577/(2π)` = 0.092 Hz
the natural frequency of the system is 0.092 Hz.
A 20-lb weight has a period of 0.18 seconds.
What is the spring constant of the system?
Given,
Mass of weight (m) = 20 lb
Period (T) = 0.18 seconds
Formula used
Spring constant (k) = `(4π²m)/(T²)
`Solution
Spring constant (k) = `(4π²m)/(T²)`= `(4π² × 20)/(0.18²)`= `(4π² × 20)/(0.0324)`= 248.2 lb/in
the spring constant of the system is 248.2 lb/in.
To know more about spring visit:
https://brainly.com/question/30106794
#SPJ11
a. Streamlines, streaklines and pathlines coincide when i. streaklines are marked in a flow with smoke or dye ii. the fluid of the flow is a gas iii. the flow is steady iv. the flow is incompressible b. The shear stress in a Newtonian fluid is i. related to rate of strain by the dynamic viscosity ii. related to the pressure field by the dynamic viscosity iii. related to the rate of strain by the density iv. related to the strain, not the rate of strain, by the dynamic viscosity c. Across a hydraulic jump i. there is a significant loss of energy ii. there is an increase in the flow depth iii. the flow transits from supercritical to subcritical iv. all of the above d. For a given flow rate in a circular pipe, the losses will be minimised by i. using a small diameter with a high flow speed ii. using a large diameter with a low flow speed iii. using a small diameter with a high flow speed, but bending the pipe iv. using two small pipes of the same total cross section area as a larger pipe e. A flow is most likely to separate when i. there is a pressure gradient where pressure increases in the direction of the flow ii. there is a pressure gradient where pressure decreases in the direction of the flow iii. there is no pressure gradient iv. there is no pressure gradient and the pressure is approaching the vapour pressure f. A "diving bell" is an apparatus that was used before the invention of SCUBA to inspect underwater structures. It consists of a platform inside a chamber or bell. The entire apparatus can be lowered, trapping air in the chamber so a person can breath as shown in the figure below. When the platform is at the free surface (h=0) the air in the chamber is at atmospheric pressure and a temperature of 15°C. Assuming the initial volume of air in the chamber is 10m³, and the temperature of the air does not vary, find . The pressure in the air chamber when the platform has been lowered to a depth of h = 5m • The volume of the air at this same depth
Streamlines, streaklines and pathlines coincide when the fluid of the flow is incompressible.b. The shear stress in a Newtonian fluid is related to rate of strain by the dynamic viscosity.
c. Across a hydraulic jump, there is a significant loss of energy, and the flow transits from supercritical to subcritical. d. For a given flow rate in a circular pipe, the losses will be minimized by using a large diameter with a low flow speed. e. A flow is most likely to separate when there is a pressure gradient where pressure increases in the direction of the flow.f. At a depth of 5m, the pressure in the air chamber is 152.5 kPa and the volume of the air is 6.45 m³.Explanation:Given that:a. Streamlines, streaklines and pathlines coincide wheni. the fluid of the flow is incompressibleb.
To know more about viscosity visit:
https://brainly.com/question/13087865
#SPJ11