A car traveling at a speed of 30. 0 m/s encounters an emergency and comes to a complete stop. how much time will it take for the car to stop if it decelerates at -4. 0 m/s^2?

Answers

Answer 1

With the help of the motion equation, it is calculated that if the vehicle slows down at a pace of -4.0 m/s², stopping will take 7.5 seconds.

Motion equation:

Three motion equations commonly referred to as the rules of constant acceleration, exist for a uniform acceleration. In order to derive the components such as displacement(s), velocity(initial =u and final = v), time(t), and acceleration(a), these equations are utilized. They are therefore only applicable in straight-line motion with constant acceleration. Here are the three equations:

v=u+at or, v = u-atv²=u²+2as  s= ut+1/2 at²

Calculating the time :

The formula for the motion equation is

v = u - at

v = final velocity

u = initial velocity

a = acceleration

t = time

Here, v = 0 ,as the automobile comes to a stop

u = 30 m/s

a = -4 m/s²

So, v = u - at

 ⇒0 = 30 - 4t

⇒4t = 30

⇒t = 30/4

⇒t = 7.5 seconds

Therefore, the required time calculated is 7.5 seconds.

Learn more about motion equations here:

https://brainly.com/question/13514745

#SPJ4


Related Questions

Which of the following electrical devices does NOT contain an electric motor?
A drill
B mixer
C toaster
D sander

Answers

the right answer is B

If your heart is beating at 76. 0 beats per minute, what is the frequency of your heart's oscillations in hertz?

Answers

If the heart is beating at 76. 0 beats per minute, the Frequency of heart's oscillations in hertz is 1.25 Hertz.

The Frequency is defined as the number of oscillations completed in 1s.

Our heart beats continuously giving rise to the frequency of the heart.

Measuring frequency would be possible if we measure the time in seconds.

75 beats per minute means that 75 beats occur in 60s.

Frequency = Number of beats / Total time taken

Frequency = 75 / 60

Frequency = 1.25 Hz

Hence, number of beats per second is 1.25 Beats.

Beats per second or Cycles per second is same as the frequency of oscillation called as Hertz (Hz)

Hence, frequency of the heart oscillation is 1.25 Hertz (Hz).

Learn more about Frequency here, https://brainly.com/question/14316711

#SPJ4

If your engine is flooded with gasoline, you should push the accelerator to the floor and hold for:_______.

Answers

You should push the accelerator all the way to the floor and hold for five seconds if your engine is flooded with gasoline.

To find the answer, we need to know about the flooded engine.

What is flooded engine?An engine that is flooded is one that has too much fuel in the vehicle and insufficient airflow.The signs of a flooded engine include difficulty starting the engine, car engine failure after only a few feet, black smoke, and unusual engine noise. We can solve the issue in different ways.In the right manner, push the accelerator or gas pedal all the way to the ground. You must open the car's throttle and let the engine's air flow before depressing the gas pedal.

Thus, we can conclude that, You should push the accelerator all the way to the floor and hold for five seconds if your engine is flooded with gasoline.

Learn more about the gasoline here:

https://brainly.com/question/15356723

#SPJ4

Southern hemisphere winds move surface water 90 degrees to the left of the direction of the wind.
a) true
b) false

Answers

Southern hemisphere winds moving surface water 90 degrees to the left of the direction of the wind is a true statement.

What is Wind?

This is referred to as the natural movement of air and other gases present in the atmosphere.

In the southern hemisphere, the surficial ocean waters which are moved by wind will result in a net perpendicular leftward movement to it thereby making it the most appropriate choice.

Read more about Wind here https://brainly.com/question/158098

#SPJ1

What total energy (in kj) is contained in 1. 0 mol of photons, all with a frequency of 2. 75 × 10^14 hz?

Answers

The total energy contained in 1 mol of photons is 109.75 KJ / mol

Given,

Frequency =  2.75 × 10 ^ 14 hz

We know that, Energy = Number of photons × Energy in one photon

                                      = n h v

                                      = (6.023 × 10^23) × ( 6.626 × 10^-34) ×( 2.75×10^14)

                                      =109.75 KJ/mol

Concepts

The total energy of a system is the sum of its gravitational potential and kinetic energy, and this total energy is preserved in orbital motion. To depart a planet and not return, objects should have a minimum velocity, known as the Escape Velocity

Learn more about total energy here : https://brainly.com/question/14062237

#SPJ4

What is the concentration of the acute leukemia cc95 combination value in micromolar (μm) units?

Answers

The concentration of the acute leukemia cc95 combination value in micromolar (μm) units is  6 × 10-4 μM.

Acute lymphocytic leukemia (ALL) is also called acute lymphoblastic leukemia. “Acute” means that the leukemia can progress quickly, and if not treated, would probably be fatal within a few months. "Lymphocytic" means it develops from early (immature) forms of lymphocytes, a type of white blood cell.

A rapidly progressing cancer that starts in blood-forming tissue such as the bone marrow, and causes large numbers of white blood cells to be produced and enter the blood stream.

In acute leukemia, the abnormal blood cells are immature blood cells (blasts). They can't carry out their normal functions, and they multiply rapidly, so the disease worsens quickly. Acute leukemia requires aggressive, timely treatment.

This corresponds to 0.6 × 10^-9 M × (1 μM/1 × 10^-6 M) = 0.6 × 10^-3 μM = 6 × 10-4 μM.

Acute myeloid leukemia (AML) is caused by a DNA mutation in the stem cells in your bone marrow that produce red blood cells, platelets and infection-fighting white blood cells. The mutation causes the stem cells to produce many more white blood cells than are needed.

To learn more about Acute lymphocytic leukemia

https://brainly.com/question/10483684

#SPJ4

What is the momentum of a tiger that has a mass of 81 kg and runs with a velocity of 5. 4 m/s to the east? (1 point)

Answers

The momentum of a tiger that has a mass of 81 kg and runs with a velocity of 5. 4 m/s to the east will be  437.4 Kg m/s in east direction.

Momentum is a property of a moving body that the body has by virtue of its mass and motion and that is equal to the product of the body's mass and velocity broadly .It is a property of a moving body that determines the length of time required to bring it to rest when under the action of a constant force.

momentum = mass * velocity

given

mass of tiger = 81 kg

velocity of tiger = 5.4 m/s

since ,

momentum = m * v

                   = 81 * 5.4 = 437.4 Kg m/s

To learn more about momentum here

https://brainly.com/question/904448

#SPJ4

What would the speed of an observer be if a red (4. 688 × 1014 hz) traffic light appeared green (5. 555 × 1014 hz) to the observer?

Answers

The speed of an observer be if a red (4. 688 × 1014 hz) traffic light appeared green (5. 555 × 1014 hz) to the observer is 0.185v using doppler effect

Utilize the approximation of the Doppler shift formula, (delta f)/f = V/c, for V/c 1 to determine which V on the list is closest. It's a little trickier to calculate the precise Doppler shift formula for light. Use what you are aware of. It is often exclusively covered in relativity theory classes. The formula for the Doppler shift of sound heard by a moving observer is NOT the same.

5.551*107 m/s = (Delta f)/f = 0.185 V.

Doppler radar transmits energy in pulses and detects any signal that is returned. The "Doppler shift" seen with sound waves is comparable to the phase shift effect. Due to compression (a change in phase) of sound waves, the "Doppler shift" causes the sound pitch of an item traveling toward you to be higher.

To learn more about the doppler shift please visit -
https://brainly.com/question/15318474
#SPJ4

What mechanisms function to localize sound in the horizontal and vertical planes?

Answers

What mechanisms function to localize sound in the horizontal and vertical planes?

Horizontal sound localization results from two mechanisms: interaural time delay and interaural intensity difference.

What is localizing sound?

The capacity to pinpoint the position or source of a detected sound in terms of distance and direction is known as sound localization.

Numerous studies have been conducted on the mammalian auditory system's sound localization mechanisms. The auditory system uses a variety of indicators, such as spectral information, timing difference, level difference (or intensity difference) between the ears, and others, to locate the source of sound. Other animals, including birds and reptiles, employ these cues as well, however there may be variances in how they are used. In addition, there are localization cues that are not present in the human auditory system, such as the results of ear movements. It is obvious that animals that can localize sound have an evolutionary advantage.

To learn more about localizing sound from the given link:

https://brainly.com/question/13044885

#SPJ4

If a car driving down the road doubles its speed what happens to its kinetic energy?

Answers

Answer:

Kinetic energy doubles

According to hubble's law, with = 70 km/s. What is the recessional velocity of a galaxy at a distance of 180 mpc?

Answers

The recessional velocity of a galaxy at a distance of 180 mpc will be 70 km/sec

Hubble's law, which says simply that a galaxy's velocity (or as is sometimes plotted, its redshift) is directly proportional to its distance, also tells us something important about the state of the universe. If the universe is static and unchanging, there should be no correlation between distance and velocity.

Recessional velocity is the rate at which an extragalactic astronomical object recedes (becomes more distant) from an observer as a result of the expansion of the universe. It can be measured by observing the wavelength shifts of spectral lines emitted by the object, known as the object's cosmological redshift.

Recessional velocity = Hubble's  constant *  distance

                                  = 70 km/sec/Mpc * 180 Mpc

                                  = 70 km/sec

To learn more about recessional velocity here

https://brainly.com/question/19578750

#SPJ4

Copernicus's model of the universe differs from Ptolemy's because Copernicus believed

Answers

Copernicus's model of the universe differs from Ptolemy's because Copernicus believed the Sun is at the center of the universe and majority of the bodies in the universe revolves around the Sun.

What is the Universe?

The universe is defined as the open place that contains the planets, stars, galaxies, and all other forms of matter and energy.

There are different models of the universe including which contains the Copernicus's model and Ptolemy's model.

The Copernicus's model of the universe differs from Ptolemy's because Copernicus believed the Sun is at the center of the universe and majority of the bodies in the universe revolves around the Sun.

While the Ptolemy's model of the universe differs from the Copernicus's model because Ptolemy believed that the Earth is at the center of the universe and everything in the universe revolves around the Earth.

Learn more about earth here:

https://brainly.com/question/15205710

#SPJ1

what happens to temperature of a substance during phase change

Answers

Answer: Nothing

Explanation:

The supplied energy is used for phase transition, not molecule kinetic energy.

Example: ice cannot be heated above 0Cº when it is being melted. Heat is consumed for phase change during its transition from solid to liquid. Only after all ice has melted, the temperature will rise until the next phase transition - vapor.

A 5. 0-c charge is 10 m from a small test charge. what is the magnitude of the force experienced by a 1. 0 nc charge placed at the location of the test charge?

Answers

The magnitude of the force experienced by a 1. 0 c charge placed at the location of the test charge is 4.5*10^8N.

To find the answer, we have to know more about the force experienced between two charges.

How to find the force experienced between two charges?It is given that,

                [tex]Q_1=5C\\Q_2=1C\\r=10m.[/tex]

We have to find the force experienced between two charges,

               [tex]F=\frac{kQ_1Q_2}{r^2}[/tex]

where, k=8.99*10^9.

Thus, by substitution, the force will be,

          [tex]F=\frac{8.99*10^9*5*1}{10^2} =4.5*10^8N[/tex]

Thus, we can conclude that, the magnitude of the force experienced by a 1. 0 c charge placed at the location of the test charge is 4.5*10^8N.

Learn more about the force here:

https://brainly.com/question/4086258

#SPJ4

Does the principle of optical reversibility hold for reflection as well as refraction? explain

Answers

Yes , principle of optical reversibility hold for reflection as well as refraction

Reflection involves a change in direction of waves when they bounce off a barrier. Refraction of waves involves a change in the direction of waves as they pass from one medium to another. Refraction, or the bending of the path of the waves, is accompanied by a change in speed and wavelength of the waves.

The principle of reversibility of light states that light follows the same path if the direction of the travel of light is reversed.

This means that if a light ray travels from medium 1 to medium 2 and has angle of incidence and angle of refraction as i and r respectively, then if the light is incident from medium 2 at an angle r, then the angle of refraction in medium 1 will be i.

The principle of reversibility presumes that the attenuation of a light ray during its passage through an optical medium because of reflection, refraction, and absorption is not affected by a reversal of the direction of the ray.

To learn more about refraction here

https://brainly.com/question/14760207

#SPJ4

How many minutes will it take to plate out 16. 22 g of al metal from a solution of al 3 using a current of 12. 9 amps in an electrolytic cell?

Answers

It will take  103 minutes  to plate out 16. 22 g of al metal from a solution of al 3 using a current of 12. 9 amps in an electrolytic cell

Electrolytic cell, any device in which electrical energy is converted to chemical energy, or vice versa. Such a cell typically consists of two metallic or electronic conductors (electrodes) held apart from each other and in contact with an electrolyte (q.v.), usually a dissolved or fused ionic compound

First, look at the reaction to decided how many moles of electrons it will take:

Al3+ + 3e ------> Al(s)

It takes 3 electrons to convert 1 mole of Al3+

Next, figure out how many moles of Al metal you want:

I mole of Al mass = 26 g

1 g of Al will have = 1/26 moles

16. 22 g of al metal will have = 16.22 / 26 moles 0.624 moles

since , their are 3 electrons

0.624 x 3= 1.87 moles of electrons

using Faraday constant to find the number of coulombs (C) needed:

1 faraday = 96500 C per mole

1.87 x 96500 = 180455

Since,  1 amp = 1 C/sec,, time needed to supply a current of 12.9 amp will be

80455C  / 12.9 C = 6236.82 sec = 103 minutes

To learn more about electrolytic cell here

https://brainly.com/question/862677

#SPJ4

Select the correct answer. which object has the least amount of kinetic energy? a. a car driving down a road b. a soccer ball rolling down a hill c. a bicycle locked to a bike rack d. a satellite orbiting earth

Answers

Answer:

c. a bicycle locked to a bike rack

Answer: Option (C). A bicycle locked to a bike rack.

The age of the dead sea scrolls was found by carbon-14 dating. could this technique have worked if they were carved in stone tablets? explain

Answers

A Final statement or concluding statement

No because this method of dating requires a material that was once living. So, this technique wouldn’t have worked.

Why carbon - 14 dating is not reliable?

Carbon 14 gradually decays into other elements. However, when a plant or animal dies, it no longer has the ability to accumulate new carbon 14, and the supply in the organism at the time of death is gradually depleted.

Scientists can calculate the time elapsed since something died from its residual carbon 14 because the rate of depletion has been accurately determined (half of any given amount of carbon 14 decays in 5,730 years).

However, scientists have long recognized that carbon dating is subject to error due to a variety of factors, including contamination from outside carbon sources. As a result, they sought methods to calibrate and correct the carbon dating method.

To learn more about Carbon Dating – 14 from the given link

https://brainly.com/question/15333408

#SPJ4

A beaker was weighed on an electronic balance. the display showed 56. 078 grams. what mass should you record for the empty beaker?

Answers

Answer:

56.18 grams because you have to round it off

Each giant planet has a core made of ________ that is 5 to 10 times the mass of earth.

Answers

The core of each giant planet is made up of rocky materials, which is 5 to 10 times the mass of earth.

To find the answer, we have to know more about the rocky materials.

What are rocky materials?The term rocky material refers to materials predominantly made up of the elements carbon, nitrogen, and oxygen in combination with hydrogen. A core of "ice" and "rock" equal to around 10 Earth masses exists within each large planet. Major internal heat sources on Jupiter, Saturn, and Neptune allow them to absorb as much (or perhaps more) energy as they do from solar radiation. There is no discernible interior heat in Uranus.

Thus, we can conclude that, the core of each giant planet is made up of rocky materials, which is 5 to 10 times the mass of earth.

Learn more about the rocky materials here:

https://brainly.com/question/15386297

#SPJ4

28. Water on the road can cause a vehicle to hydroplane. Your car may hydroplane at speeds as low as:

Answers

Your car may hydroplane at speed as low as 56 Kilometer per hour

What can cause a car to Hydroplane ?

Hydroplaning occurs mostly during the raining period. When the tire of the car continue to loose grip and start skidding on the road surface.

It is true that water on the road can cause a vehicle to hydroplane. And your car may hydroplane at speeds as low as 35 mile per hour or approximately 56 kilometer per hour.

The three main factors of the car hydroplaning are;

Water depth which can determine how quicker a car can lose traction.Increase in speed of the vehicle. Increase in speed causes wet traction to reduce.Tire tread depth. Worn out tires could have less ability to resist hydroplaning.

Therefore, your car may hydroplane at speeds as low as 56 Kilometer per hour approximately.

Learn more about about Hydroplaning here: https://brainly.com/question/24304671

#SPJ1

By how much will the runner's achilles tendon stretch if the force on it is 8.0 times his weight? young's modulus for tendon is 0.15×1010n/m2.

Answers

The runner's achilles tendon stretch is 5mm.

What is Young's modulus?

Young's modulus (Y) is described by the following expression.

[tex]Y = \frac{F \times L}{ΔL \times A } [/tex]

where,

F=force exerted on the tendon

A=area

∆L=change in length (streching)

The force in this case is 8 times the weight of the runner

F=8×m×g

F=8×70×9.8

F=5488N

therefore,the change in length of the tendon is given by

[tex]Δ = \frac{F \times L}{ Y \times A } [/tex]

[tex]ΔL = \frac{5488 \times 0.15}{0.15 \times 10 {}^{10} \times 1.1 \times 10 {}^{ - 9} } [/tex]

ΔL=0.00498m

The runner's achilles tendon will stretch by 0.004989m which is approx.5mm

Learn more about Young's modulus from here: https://brainly.com/question/28147111

#SPJ4

The helium-neon lasers most commonly used in student physics laboratories have average power outputs of 0. 250 mw. True or false?.

Answers

Intensity of laser beam is 72.3W/m²

Given:

average power output = 0. 250 mw

To Find:

intensity of laser beam

Solution:

First of all, we need to find the area of the circular spot, which is given by:

A = πr^2

where r is the radius of the spot, which is half the diameter, therefore

r = d/2 = 2.10mm/2 = 1.05mm = 1.05 x 10^-3m

So, the area of the spot is

A = π(1.05 10^-3m)^2 = 3.46 10^-6m²

We know that the power output of the laser is

P = 0.250mW = 2.5.10^-4W

So the intensity of the laser beam is

I = P/A = 2.5^-10 W/3.46-10^-6m^2 = 72.3W/m²

So, intensity of laser beam is 72.3W/m²

Learn more about Intensity here:

https://brainly.com/question/14924672

#SPJ4

An rv is traveling 60 km/h along a highway at night. a boy sitting near the driver of the rv turns a flashlight on and shines it at another boy at the back end of the rv. what is the speed of the light relative to the boys? m/s what is the speed of light relative to a stationary observer on the side of the road? m/s

Answers

Speed of light relative to the boys = 300,000,000 m/s

Speed of light relative to a stationary observer on the side of the road =

300,000,000 m/sWhat is special theory of relativity?The theory of special relativity explains how speed affects space, time, and mass. Small amounts of mass (m) can be interchangeable with large amounts of energy (E), as defined by the classic equation E = mc2, according to the theory, which offers a means for the speed of light to define the link between energy and matter.

What are the special relativity's guiding principles?The laws of physics should be independent of the uniform motion of an inertial frame of reference, and the speed of light should be constant in any such frame, according to two fundamental tenets that constitute the basis of the special theory of relativity.

To learn more about special relativity visit:

https://brainly.com/question/12497537

#SPJ4

Answer:

first answers are 25 & 35, second answers are both 300,000,000

Explanation:

The potential energy at x = 8 m is -2000 V and at x = 2 m is 400 V. What is the magnitude and direction of the electric field?

Answers

The potential energy at x = 8 m is -2000 V and at x = 2 m is 400 V. The magnitude and direction of the electric field will be 400 V/m directed parallel to the +x-axis

Electric field, an electric property associated with each point in space when charge is present in any form. The magnitude and direction of the electric field are expressed by the value of E, called electric field strength or electric field intensity or simply the electric field.

The electric potential energy of any given charge or system of changes is termed as the total work done by an external agent in bringing the charge or the system of charges from infinity to the present configuration without undergoing any acceleration.

The relation between electric field and electric potential can be generally expressed as – “Electric field is the negative space derivative of electric potential.”

Electric field = - d V / dx

-(-2000-400) = [tex]\int\ {E} \, dx[/tex]

2400 = E (8-2)

2400 V = E (6)

E = 400 V/m

To learn more about electric potential energy  here

https://brainly.com/question/16890427

#SPJ4

Very low temperature molecular clouds emit most of their light in which part of the electromagnetic spectrum?

Answers

The radio region of the electromagnetic spectrum is where molecular clouds with extremely low temperatures emit the majority of their light.

To find the answer, we need to know more about the molecular clouds.

What is molecular clouds?Only within molecular clouds can stars actually form. Because the internal forces operating "outward" to prevent a collapse must be greater than the gravitational force acting to collapse the cloud, this is a natural result of their high densities and low temperatures.At 10 K, molecular clouds are extremely cold. Clouds that are diffuse are usually 100 K. Depending on the abundances of heavy elements that provide the cooling radiation, HII areas have T 8000 K.

Thus, we can conclude that, the radio region of the electromagnetic spectrum is where molecular clouds with extremely low temperatures emit the majority of their light.

Learn more about the molecular clouds here:

https://brainly.com/question/13838387

#SPJ4

Derive an Expression for elastic potential energy of a spring

Answers

Answer:

spring force = -K × x , where X is elongation or compression in the spring. ( -) sigh shows that the spring force is opposite to the applied force to cause extension.

Potential energy = work done by spring force = integration of Force.

integrate the force (-K × x) over distance 0 to x .

U = 1/2 K × X^2 ( for elongation)

U = -1/2 × K × X^2 ( for compression)

What must be done to the refrigerant that is vented off the top when filling a charging cylinder?

Answers

When filling a charging cylinder with a regulated refrigerant; The refrigerant vapor that is vented off the top of the cylinder must be recovered. If after installing a fitting for the purpose of recovering the appliances refrigerant, you find that the system pressure is 0 psig; Recovery is not required.

When transporting cylinders contain used refrigerant?

The DOT mandates that DOT Classification Tags, such as those shown above, be attached to cylinders that contain used refrigerant. DOT classification tags show the substance's level of hazard and are arranged according to class. For instance, Class 2, which is gases, would include refrigerant gases.

What must be done before shipping any used refrigerant in a cylinder?

Check that the cylinder complies with DOT requirements before sending any old refrigerant cylinders, fill out the shipping paperwork with the quantity of each refrigerant, and clearly mark the cylinder with the kind and amount of refrigerant. Transporting cylinders should be done standing up.

Learn more about refrigerant of cylinder

brainly.com/question/10054719

#SPJ4

Separately derived system generators shall have the _______________ conductor sized not smaller than required to carry the maximum unbalanced current as determined by NEC Article 220.61.

Answers

Separately derived system generators shall have the neutral conductor sized not smaller than required to carry the maximum unbalanced current as determined by NEC Article 220.61.

What is an electric charge?

Charged material experiences a force when it is exposed to an electromagnetic field due to the physical property of electric charge. You can have a positive or negative electric charge.

Electric current is defined as the charge per unit of time.

The mathematical relation between current and the electric charge

I =Q/T

Generators are basically motors that operate in reverse—they produce electricity when rotated, instead of rotating when supplied with electricity

The conductors that come from generators must be sized, and overload protection is required. But compared to similar considerations for motors, these considerations are much simpler.

Thus, The neutral conductor on separately derived system generators must be no smaller than necessary to carry the maximum unbalanced current as specified by NEC Article 220.61.

Learn more about an electric charge from here

brainly.com/question/8163163

#SPJ1


A proton moves a distance 10 cm in a uniform electric field of 3.5 kN C, in the direction of the field.
Calculate the change in potential energy of the proton.

Answers

The change in potential energy of the proton is  5.6 x [tex]10^{-17}[/tex] Joule

What is a Uniform Electric Field ?

A uniform electric field is where the electric field strength is the same at all points in the field. In the uniform field, the force experienced by a charge is the same no matter where it is placed in the field.

Given that a proton moves a distance 10 cm in a uniform electric field of 3.5 kN C, in the direction of the field.

The distance d = 10 cm = 0.1 mElectric field E = 3.5 KN/CProton charge q = 1.6 x [tex]10^{-19}[/tex] C

The Work done = Fd

but F = Eq

Recall that Electric field E = F/q = V/d

Where V = potential difference.

Let us first calculate the V

E = V/d

V = Ed

Substitute all the parameters into the formula above

V = 3.5 × 10³ × 0.1

V = 350 v

from F/q = V/d

make F the subject of formula and substitute it in work formula

F = Vq/d

W.D = Vq/d x d

W.D = Vq

Substitute all the parameters into the formula above

W.D = 350 x 1.6 x [tex]10^{-19}[/tex]

W.D = 5.6 x [tex]10^{-17}[/tex] J

Work done = Energy = Potential Energy

Therefore, the change in potential energy of the proton is 5.6 x [tex]10^{-17}[/tex] Joule

Learn more about Electric Field here: https://brainly.com/question/14372859

#SPJ1

Other Questions
The python standard library's __________ module contains numerous functions that can be used in mathematical calculations. Julio wants to calculate 200,000 300,000. When he used his calculator to multiply, it showed the result below:6E+10Write the number shown on the calculator display in standard form. Explain the conceptual and quantitative relationships between alpha risk and beta risk when testing hypotheses, and include the impact sample size plays in managing these risk levels Which is a central idea of Sagoyewatha's speech, "We Are Determined Not to Sell Our Lands"?Indigenous people need to fight against the US government in order to take back the lands gained under false pretenses. The US government needs to give back the land that was sold to the Yorkers because the Yorkers bought the land illegally. Indigenous people cannot give up any more land to the US government because there is no more land big enough for them to live on.The US government needs to admit their mistake in letting its people buy land when they had no right to do so. For the reaction c 2h ---> ch, how many moles of hydrogen are required to produce 10 mol of methane, ch Write an essay on Contribution of Technology in Education. 1. Effective time-management skills include: A. Scheduling random times for sleeping and eating. B. Leaving unscheduled time in your schedule to allow for the unexpected. C. Studying 10 minutes for every hour in class. D. Filling every minute outside of class with an action activity.2. Which of the following is the LEAST APPROPRIATE support service that may contribute directly towards completing a class-directed activity? A. Job Placement Center B. Learning Resource Center C. Counseling D. Library3. Effective communication involves which of the following: A. Listening as well as speaking. B. Using I messages. C. Expressing ones ideas clearly and thoroughly. D. All of the above.4. In become a critical thinker, it is essential to: A. Rely on stereotypes. B. Make decisions based on your biases. C. Not question authority D. Analyze and communicate our position based on facts. The first step of amino acid degradation involves removal of the alpha-amino group to give the corresponding alpha-keto acid. what is this process called? The form of federal assistance called ________ provides money to state governments with few strings attached. Select the correct answer.What is the exact value of cos 105?A 6-2B. 6 + 2. V2 - V6D. -2+6 The administrator may deny or revoke a securities registration by:_______ a. rule b. order c. edict d. subpoena What activity, process, or asset best allows successful planners to simultaneously move quickly and patiently? What was the most notable asset of the crusader army that travelled to the holy land in 1096? What is the component form of the vector that translates the top house figure to thebottom house figure? The right to privacy was instrumental in which decision? multiple choice roe v. wade mapp v. ohio schenck v. united states miranda v. arizona new york times co. v. united states PLEASE HELP: How does the Allusion "Dix Hill" reveal a specific time or place in the story "The Scarlet Ibis" What does a router do with a packet that it does not have a destination network for? A portion of the quadratic formula proof is shown. Fill in the missing statement ( the last answer choice is (x + b/2a = + b^2-4ac/a) Jaquelyn wants to start getting to school on time more often. She is looking at some of her habits.On Monday, she is late twenty percent of the time. When she is late on Monday, she is late on Tuesday 60% of the time. When she is not late on Monday, she is late on Tuesday 20% of the time. What is the approximate probability that Jaquelyn will be late on Tuesday, given she was late to school on Monday? Industry and market analysis, competitor analysis, and social analysis are examples of which step in the strategic planning process?