The angular frequency at which the current amplitude in the RLC circuit reaches its maximum value is determined by the values of resistance, capacitance, and inductance in the circuit.
In an RLC circuit, resonance occurs when the reactive components, namely the inductor and capacitor, cancel each other out, allowing the current to flow with maximum amplitude. The angular frequency at resonance can be found using the formula:
ω = 1 / √(LC)
where ω represents the angular frequency, L is the inductance, and C is the capacitance. Given the values L = 1.00 H and C = 20.0 F, we can substitute these values into the formula to find the angular frequency at resonance.
To determine the maximum value of the current amplitude at resonance, we need to consider the voltage source E and the resistance R in the circuit. The current amplitude at resonance can be calculated using the formula:
I = E / R
where I represents the current amplitude and E is the voltage source. Given E = -30.0 V and R = 5.00 Ω, we can substitute these values into the formula to find the maximum value of the current amplitude.
To find the angular frequencies at which the current amplitude is half the maximum value, we need to consider the concept of the half-power points on the resonance curve. The half-power points occur when the current amplitude is reduced to half its maximum value. Mathematically, these angular frequencies can be determined by solving the equation:
ω = ± √(ω0^2 - (Γ/2)^2)
where ω represents the angular frequency, ω0 is the angular frequency at resonance, and Γ is the half-width of the resonance curve. By substituting the given values into the equation, we can find the lower and higher angular frequencies at which the current amplitude is half the maximum value.
Finally, the fractional half-width of the resonance curve (W1-W2) can be calculated by using the formula:
(W1-W2) = Γ / ω0
where W1 and W2 represent the lower and higher angular frequencies, respectively, and ω0 is the angular frequency at resonance.
Learn more about Frequency
brainly.com/question/29739263
#SPJ11
what is the most common manifold pressure for propane furnaces
The most common manifold pressure for propane furnaces is typically around 10.5 inches of water column (WC).
Manifold pressure is the pressure of the gas in the gas valve while it is not being consumed by the burners. The gas valve in a propane furnace provides a steady supply of fuel to the burners based on the pressure present in the manifold. The most common manifold pressure for propane furnaces is approximately 10.5 inches of water column (WC). This pressure can be increased or decreased slightly to suit the specific needs of the appliance, but it is not recommended to go beyond the limits established by the manufacturer, as this may cause a malfunction or even a safety hazard. In addition to propane furnaces, other gas appliances such as water heaters, ovens, and stoves also have a manifold pressure. The specific pressure requirements for each appliance can be found in the manufacturer's instructions or on the data plate attached to the appliance.
To know more about propane furnaces please refer to:
https://brainly.com/question/33346901
#SPJ11
In a region of space, the electric field is directed in the +y direction and has a magnitude of 4000 V/m. What is the potential difference from the coordinate origin to the points? (x,y,z)=(0,20 cm,0)ΔV= (x,y,z)=(0,−30 cm,0)ΔV= (x,y,z)=(0,0 cm,15 cm)ΔV=
Potential difference (V) is the amount of work done to move a unit charge between two points in an electric field. It is measured in volts (V).Potential difference, ΔV = Vfinal − Vinitial
The potential difference is also equal to the product of the electric field strength and the distance between the two points, expressed mathematically as
ΔV = Ed
where E is the electric field strength and d is the distance between the points.
ΔV=Ed
The given electric field has a magnitude of 4000 V/m and it's directed in the +y direction.
In (x,y,z)=(0,20 cm,0),
the distance between the origin and the point is 0.2m.
Hence the potential difference is ΔV = Ed = 4000V/m × 0.2m = 800VΔV for (x,y,z)=(0,20 cm,0) is 800V.
In (x,y,z)=(0,−30 cm,0),
the distance between the origin and the point is 0.3m and the electric field is directed in the +y direction.
Hence the potential difference is ΔV = Ed = 4000V/m × 0.3m = 1200V.ΔV for
(x,y,z)=(0,−30 cm,0) is 1200V. In (x,y,z)=(0,0 cm,15 cm),
the distance between the origin and the point is 0.15m.
The electric field is directed in the +y direction.
Hence the potential difference is ΔV = Ed = 4000V/m × 0.15m = 600VΔV for (x,y,z)=(0,0 cm,15 cm) is 600V.
The potential difference for (x,y,z)=(0,20 cm,0) is 800V, for (x,y,z)=(0,−30 cm,0) is 1200V and for
(x,y,z)=(0,0 cm,15 cm) is 600V.
To know more about amount visit :
https://brainly.com/question/32453941
#SPJ11
An old film camera, with a 50.25 mm focal length lens, is used to take a photo of an object. If the lens is 52.61 mm away from the film (where the image is captured), how far away is an object (in metres) that is in focus? Give your answer to 2 decimal places.
The object that is in focus is located at a distance of 49.66 meters from the old film camera.
To determine the distance, we can use the thin lens equation, which relates the object distance (denoted as "u"), the image distance (denoted as "v"), and the focal length of the lens (denoted as "f"). The thin lens equation is given by:
1/f = 1/v - 1/u
In this case, we are given the focal length "f" as 50.25 mm and the image distance "v" as 52.61 mm. We need to solve for the object distance "u."
Converting the focal length and image distance from millimeters to meters, we have f = 0.05025 m and v = 0.05261 m. Plugging these values into the thin lens equation and solving for "u," we get:
1/0.05025 = 1/0.05261 - 1/u
Simplifying the equation, we find:
0.05261 - 0.05025 = 1/u
0.00236 = 1/u
u = 1/0.00236
u ≈ 424.58 m
Therefore, the object that is in focus is approximately 424.58 meters away from the old film camera.
To learn more about distance, click here: https://brainly.com/question/13034462
#SPJ11
Consider the force F = -axi- byj - cz² k, where a, b, and c are constants. a) Is the force conservative? Show work. (4pts) b) If so, find the corresponding potential energy function U. (4pts) c) Find the work done by the force in moving an object from the origin
a) The force is non-conservative.
b) It does not have a potential energy function
c) The work done by the force is `(-3a + 12b - 5c)/10`.
Consider the force `F = -axi- byj - cz² k` where `a`, `b`, and `c` are constants. The solution is as follows:
a) The force F is conservative if and only if the curl of F is equal to zero.`∇ x F = ∂(cz²) / ∂y - ∂(-by) / ∂z + ∂(-ax) / ∂z ≠ 0`
Therefore, the force is non-conservative.
b) The force is non-conservative, hence it does not have a potential energy function U. Therefore, the second part of the question is incorrect.
c) The work done by the force in moving an object from the origin is the line integral of the force F from the origin to the final point P.
This can be written as:`W = ∫_C F.dl`
The path C from the origin O to point P can be parametrized as:r(t) = ti + t²j + t³k, where 0 ≤ t ≤ 1.`dr/dt = i + 2tj + 3t²k`
Hence, the line integral of F from O to P is:
`W = ∫_C F.dl`
`W = ∫_0¹ F.(dr/dt)dt`
`W = ∫_0¹(-at)i - (bt²)j - (ct⁴)k.(i + 2tj + 3t²k)dt`
`W = ∫_0¹(-at)dt - ∫_0¹ bt²(2t)dt - ∫_0¹ ct⁴(3t²)dt`
`W = [-a/2 t²]_0¹1 - [2b/5 t⁵]_0¹ - [3c/6 t⁷]_0¹`
`W = -a/2 - 2b/5 - 3c/6`
`W = (-3a + 12b - 5c)/10`
Hence, the work done by the force in moving an object from the origin is `(-3a + 12b - 5c)/10`.
Learn more about potential function at
https://brainly.com/question/14214954
#SPJ11
Two identical particles, each of mass m, are Part A located on the x axis at x=+x
0
and x=−x
0
. Determine a formula for the gravitational field due to these two particles for points on the y axis; that is, write
g
as a function of y,m,x
0
, and so on. Express your answers in terms of the variables y,m,x
0
, and appropriate constants. Enter your answers separated by a comma. At what point (or points) on the y axis is the magnitude of
g
a maximum value, and what is its value there? [Hint: Take the derivative d
g
/dy.] Express your answer(s) in terms of the variables y,m,x
0
, and appropriate constants. If there is more than one point, enter each point separated by a comma. What is the maximum value of the magnitude of
g
? Express your answers in terms of the variables y,m,x
0
, and appropriate constants.
Gravitational field due to two particles for points on y-axis can be written as:
[tex]$$\frac{Gm}{r_1^2}-\frac{Gm}{r_2^2}$$Where$$r_1=\sqrt{x_0^2+y^2},$$$$r_2=\sqrt{x_0^2+y^2}$$$$r_1^2=(x_0^2+y^2),$$$$r_2^2=(x_0^2+y^2)$$Hence$$\frac{Gm}{r_1^2}-\frac{Gm}{r_2^2}=Gm\left(\frac{1}{x_0^2+y^2}-\frac{1}{x_0^2+y^2}\right)=0$$[/tex]
The magnitude of g is zero for all points on y-axis.Maximum or minimum of magnitude of g occurs when
[tex]$$\frac{dg}{dy}=0$$[/tex]
Differentiating g with respect to y, we have
[tex]$$\frac{dg}{dy}=Gm\left(-\frac{2y}{(x_0^2+y^2)^2}\right)$$$$\frac{dg}{dy}=0 \implies y=0$$[/tex]
Therefore, the maximum value of the magnitude of g is given by:
[tex]$$g_{max}=Gm\left(\frac{1}{x_0^2}\right)$$[/tex]
Therefore, the magnitude of g is maximum at the points of y-axis, which intersect the line joining the two particles. At such points, the magnitude of g is equal to
[tex]$g_{max}=Gm\left(\frac{1}{x_0^2}\right)$.[/tex]
To know more about Gravitational visit:
https://brainly.com/question/3009841
#SPJ11
ll 4. A beam in a cathode ray tube is passed between oppositely charged parallel plates. Using principles of physics, explain why increasing the deflecting voltage across the plates affects the path of the beam. (4 marks) 1 CS Scanned with CamScanner
The Lorentz force is a force that acts on a charged particle in an electric field. The force is proportional to the charge of the particle and the strength of the electric field. The direction of the force is perpendicular to both the electric field and the velocity of the particle.
In the case of a cathode ray tube, the beam of electrons is negatively charged. When the electrons pass through the electric field between the plates, they experience a force that is directed towards the positive plate. This force deflects the beam of electrons towards the positive plate. The amount of deflection is proportional to the strength of the electric field and the charge of the particles. Increasing the deflecting voltage across the plates increases the strength of the electric field, which in turn increases the amount of deflection of the beam.
The deflection of the beam can be used to control the position of the beam on the screen of the cathode ray tube. This is how images are created on a cathode ray tube display.
To know more about cathode ray tube, click here:-
https://brainly.com/question/32443811
#SPJ11
A drop of oil is immersed in a tank of water and falls far enough down that the pressure increases by 1 atmosphere (atm) compared to the pressure at the surface. What is the fractional change in the drop's volume due to the water pressure? You may assume bulk modulus for the oil is 5×10
9
Pa, and that 1 atm=10
5
Pa.
The fractional change in the drop's volume due to the water pressure is 2 × 10⁻⁵.Bulk modulus of oil, K = 5 × 10⁹ Pa, Pressure difference, ΔP = 1 atm = 10⁵ Pa and Change in volume, ΔV/V = ?.
We know that the relationship between bulk modulus, pressure difference, and the change in volume is given as;Bulk modulus = pressure difference × (original volume / change in volume)K = ΔP × (V / ΔV).
On rearranging the above formula we get,ΔV/V = ΔP / K.
Substitute the given values,ΔV/V = ΔP / KΔV/V = 10⁵ Pa / (5 × 10⁹ Pa)ΔV/V = 2 × 10⁻⁵.
The fractional change in the drop's volume due to the water pressure is 2 × 10⁻⁵.
Learn more about bulk modulus here ;
https://brainly.com/question/28295935
#SPJ11
a) 1 m3 of gas is contained in a rigid sealed cylinder at an initial pressure of 0.15 bar and a temperature of 27∘C. It is heated to a temperature of 147∘C. Given: The gas has a molecular weight of 32 kg/kmol. The universal gas constant, Ro is 8,314 J/kmol⋅K. The specific heat capacity at constant volume, Cv, is 0.659 kJ/kg⋅K. Assuming that the gas is an ideal gas. (i) Calculate the gas constant (R) for the gas. (2 Marks) (ii) Calculate the mass (m) of the gas inside the cylinder. (3 Marks) (iii) Calculate the change in internal energy of the gas. (2 Marks) (iv) Calculate the final pressure of the gas at a temperature of 147∘C. (3 Marks) (v) Draw the pressure-volume diagram to illustrate the change of gas in the abovementioned process. (6 Marks) (b) Figure Q3 shows a mercury U-tube manometer that used to determine the pressure difference between points A and B. Determine the pressure at point B. (4 Marks) Given: a=1.6 m, b=1 m and h=0.5 m. Pressure at Point A(PA)=70,000 Pa. Density of the water =1,000 kg/m3. Relative density of the mercury =13.6.
(a). (i) The gas constant (R) for the gas is 259.81 J/kg⋅K.
(ii) The mass (m) of the gas inside the cylinder is approximately 1.51 kg.
(iii) The change in internal energy of the gas is approximately 145.37 kJ.
(iv) The final pressure of the gas at a temperature of 147∘C is approximately 6,370.39 Pa. (b) The pressure at point B in the mercury U-tube manometer is approximately 75,900 Pa.
(i) To calculate the gas constant (R) for the gas, we can use the formula R = Ro / M, where Ro is the universal gas constant and M is the molecular weight of the gas. Substituting the given values, we have R = 8,314 J/kmol⋅K / (32 kg/kmol), which gives R = 259.81 J/kg⋅K.
(ii) The mass (m) of the gas inside the cylinder can be calculated using the ideal gas law equation PV = mRT, where P is the initial pressure, V is the volume, R is the gas constant, and T is the temperature. Rearranging the equation, we have m = PV / (RT). Substituting the given values, we have m = (0.15 bar * 100,000 Pa/bar) * (1 m3) / ((259.81 J/kg⋅K) * (27 + 273) K), which gives m ≈ 1.51 kg.
(iii) The change in internal energy of the gas can be calculated using the equation ΔU = m * Cv * ΔT, where m is the mass, Cv is the specific heat capacity at constant volume, and ΔT is the change in temperature. Substituting the given values, we have ΔU = (1.51 kg) * (0.659 kJ/kg⋅K) * (147 - 27) K, which gives ΔU ≈ 145.37 kJ.
(iv) To calculate the final pressure of the gas at a temperature of 147∘C, we can use the ideal gas law equation PV = mRT, where P is the final pressure, V is the volume, R is the gas constant, and T is the temperature. Rearranging the equation, we have P = mRT / V. Substituting the given values, we have P = (1.51 kg) * (259.81 J/kg⋅K) * (147 + 273) K / (1 m3), which gives P ≈ 6,370.39 Pa.
(v) The pressure-volume diagram can be illustrated as follows:
(b) To determine the pressure at point B in the mercury U-tube manometer, we can use the equation P = PA + ρgh, where P is the pressure at point B, PA is the pressure at point A, ρ is the density of the water, g is the acceleration due to gravity, and h is the height difference. Substituting the given values, we have P = 70,000 Pa + (1,000 kg/m3) * (9.8 m/s2) * (0.5 m), which gives P ≈ 75,900 Pa.
To learn more about mercury U-tube manometer, Click here:
https://brainly.com/question/21027442
#SPJ11
3) Draw the Milky Way Galaxy including the spiral arms with some detail; indicate where our Solar System is and the Sagittarius A black hole; label the arm we are in:
4) Draw the H-R Diagram, describe the information on all axes
The Milky Way Galaxy is a spiral galaxy that includes spiral arms. Our Solar System is located within one of the spiral arms, and the Sagittarius A black hole is situated at the center.
The Milky Way Galaxy is a majestic spiral galaxy that spans a vast expanse of space. It consists of multiple spiral arms that radiate outward from a central region. Our Solar System finds its place within one of these spiral arms, known as the Orion Arm or the Local Spur. The Orion Arm is a minor arm located between the larger Perseus Arm and the Sagittarius Arm. It is believed that our Solar System is situated about two-thirds of the way from the center of the galaxy to the outer edge.
At the core of the Milky Way Galaxy lies the Sagittarius A black hole, an extremely dense and massive object that exerts a gravitational pull on surrounding matter. Sagittarius A is located in the direction of the constellation Sagittarius, hence its name. This supermassive black hole has a mass equivalent to millions of suns and plays a crucial role in shaping the structure of the galaxy.
The Milky Way Galaxy is a stunning example of a spiral galaxy, featuring a beautiful arrangement of spiral arms that extend outward from the central region. Our Solar System is nestled within one of these spiral arms, specifically the Orion Arm or Local Spur. Positioned about two-thirds of the way from the center of the galaxy to its outskirts, our Solar System experiences the gravitational influence of the galaxy's core while being part of the grand cosmic tapestry.
At the heart of the Milky Way Galaxy lies the Sagittarius A black hole. This supermassive black hole, residing in the direction of the Sagittarius constellation, possesses an immense gravitational pull due to its enormous mass, which is equivalent to millions of suns. Sagittarius A plays a pivotal role in shaping the structure of the galaxy, exerting its gravitational influence on surrounding stars and matter.
To delve deeper into the intricacies of the Milky Way Galaxy, its spiral arms, and the positioning of our Solar System within this vast celestial realm, explore the fascinating field of galactic astronomy.
Learn more about Milky Way Galaxy
brainly.com/question/32872198
#SPJ11
a
solenoid is 1.6 m long and has 500 turns per meter. what is the
cross sectional area of this solenoid if it stores .31J of energy
when it carrie’s a current of 14 A?
A solenoid is an electrical component used to convert electrical energy into mechanical energy. It consists of a long, cylindrical coil of wire, which generates a magnetic field when an electric current is passed through it.
The cross-sectional area of a solenoid is an important parameter that affects its magnetic field strength. It is determined by the length of the coil, the number of turns per meter, and the amount of current passing through it.In this problem, we are given the length of the solenoid, the number of turns per meter, and the current passing through it.
We are also given the energy stored in the solenoid, which we can use to calculate the magnetic field energy density using the formula: [tex]u = (B^2)/(2μ0)[/tex]where u is the magnetic field energy density, B is the magnetic field strength, and μ0 is the permeability of free space.
Since we are given the energy stored in the solenoid, we can rearrange the formula to solve for B:B = sqrt(2uμ0)We can then use the formula for the magnetic field strength of a solenoid to calculate the cross-sectional area of the solenoid:
A = (μ0N^2I)/B where A is the cross-sectional area, N is the number of turns, and I is the current passing through the solenoid. Substituting the given values, we get: [tex]A = (4π × 10^-7 × 500^2 × 14)/sqrt(2 × 0.31) = 5.72 × 10^-5 m²[/tex]
Therefore, the cross-sectional area of the solenoid is [tex]5.72 × 10^-5 m²[/tex].
To know more about electrical visit:
https://brainly.com/question/33513737
#SPJ11
what type of measurement is this 55 miles per hour
The measurement "55 miles per hour" represents a unit of speed or velocity.
The measurement "55 miles per hour" is a unit of speed or velocity, specifically in the context of linear motion. Speed is a scalar quantity that describes how fast an object is moving, while velocity is a vector quantity that includes both speed and direction.
In this case, "55 miles per hour" indicates that an object is traveling a distance of 55 miles in one hour. The term "miles per hour" denotes the rate at which the distance is covered with respect to time.
To break it down further, the unit "miles" represents a measure of distance, and the unit "hour" represents a measure of time. The division of distance (miles) by time (hour) gives us the rate of change, which is the speed or velocity.
The value of 55 in "55 miles per hour" represents the magnitude or numerical value of the speed or velocity. It indicates that the object is moving at a rate of 55 miles per hour.
In summary, "55 miles per hour" is a measurement of speed or velocity, where the object is traveling a distance of 55 miles in one hour. It provides information about how fast the object is moving but does not indicate the direction of motion.
To know more about magnitude refer here:
https://brainly.com/question/31022175#
#SPJ11
Unpolarized light of intensity 8.4 mW/m2 is sent into a polarizing sheet as in the figure. What are (a) the amplitude of the electric field component of the transmitted light and (b) the radiation pressure on the sheet due to its absorbing some of the light?
When unpolarized light of intensity 8.4 mW/m² passes through a polarizing sheet, we need to determine the amplitude of the electric field component of the transmitted light and the radiation pressure on the sheet.
By applying the formulas related to the polarization of light and the radiation pressure, we can calculate these values.
The intensity of unpolarized light is related to the amplitude of the electric field component of the transmitted light through the equation I = 0.5 * ε₀ * c * E₀², where I is the intensity, ε₀ is the vacuum permittivity, c is the speed of light, and E₀ is the amplitude of the electric field component.
To find the amplitude of the electric field component (E₀), we rearrange the equation as E₀ = √(2 * I / (ε₀ * c)).
Substituting the given intensity value of 8.4 mW/m² into the equation and evaluating it, we can determine the amplitude of the electric field component of the transmitted light.
To calculate the radiation pressure on the sheet, we use the formula P = I / c, where P is the radiation pressure and I is the intensity of the light.
By substituting the given intensity value and the speed of light into the equation, we can determine the radiation pressure on the sheet.
Therefore, by applying the relevant formulas and performing the calculations, we can find the amplitude of the electric field component of the transmitted light and the radiation pressure on the sheet due to its absorption of the light.
Learn more about unpolarized light here:
https://brainly.com/question/33361886
#SPJ11
a- In LORN (HPF) system the speed of radio signal is 285400 m/ms, and the distance between the master station and the secondary station is 40.50 km. If the measured time difference on a certain course line is 125μs, and the boat is away from the vertex of parabola by 15.752 km at right side of C.L. Find the (x,y) coordinates of the boat (regarding the intersection of C.L. and base line is the origin).
The coordinates of the boat are (40,577 m, 15,752 m).
Let's calculate the (x, y) coordinates of the boat using the given information and the formulas mentioned earlier.
Given:
Speed of radio signal (v): 285400 m/ms
Distance between master station and secondary station (d): 40.50 km = 40,500 m
Measured time difference (t): 125 μs = 125 * 10^(-6) s
Distance from the vertex of the parabola (d1): 15.752 km = 15,752 m
First, let's find the time taken by the radio signal to travel from the master station to the secondary station:
t_total = d / v
t_total = 40,500 m / 285400 m/ms
t_total ≈ 0.1421 s
Next, we find the time taken by the radio signal to travel from the master station to the boat:
t_diff = t_total - t
t_diff = 0.1421 s - (125 * 10^(-6) s)
t_diff ≈ 0.142 s
Now, we can find the distance traveled by the radio signal from the master station to the boat:
d2 = t_diff * v
d2 = 0.142 s * 285400 m/ms
d2 ≈ 40,577 m
The (x, y) coordinates of the boat are (d2, d1), where d1 is the distance from the vertex of the parabola:
(x, y) = (40,577 m, 15,752 m)
Therefore, the coordinates of the boat are approximately (40,577 m, 15,752 m).
Learn more about coordinates from the given link
https://brainly.com/question/31293074
#SPJ11
A proton is initially at rest. After some time, a uniform electric field is turned on and the proton accelerates. The magnitude of the electric field is 1.60×10^5 N/C. (a) What ia the speed of the proton after it has traveled 2.00 cm ? m/s (b) What is the speed of the proton after it has traveled 20.0 cm ? m/s
A The speed of the proton after traveling 2.00 cm is 80 m/s , b) The speed of the proton after traveling 20.0 cm is 253 m/s.
We can use the equations of motion for uniformly accelerated motion.
(a) Find the speed of the proton after it has traveled 2.00 cm, we can use the equation:
[tex]v^2 = u^2 + 2as[/tex]
where v is the final velocity, u is the initial velocity (which is zero in this case since the proton is initially at rest), a is the acceleration, and s is the displacement.
Given that the magnitude of the electric field is 1.60×[tex]10^5[/tex] N/C, which represents the acceleration experienced by the proton, and the displacement is 2.00 cm (or 0.02 m), we can calculate the speed:
[tex]v^2[/tex]= 0 + 2 * (1.60×[tex]10^5[/tex] N/C) * (0.02 m)
[tex]v^2[/tex] = 6.40×[tex]10^3[/tex] [tex]m^2/s^2[/tex]
v ≈ 80 m/s
The speed of the proton after it has traveled 2.00 cm is approximately 80 m/s.
(b) Similarly, to find the speed of the proton after it has traveled 20.0 cm, we can use the same equation:
[tex]v^2 = u^2 + 2as[/tex]
Using the same acceleration and a displacement of 20.0 cm (or 0.20 m), we can calculate the speed:
[tex]v^2[/tex] = 0 + 2 * (1.60×[tex]10^5 N/C[/tex]) * (0.20 m)
[tex]v^2[/tex] = 6.40×[tex]10^4 m^2/s^2[/tex]
v ≈ 253 m/s
The speed of the proton after it has traveled 20.0 cm is 253 m/s.
To know more about proton refer here
https://brainly.com/question/12535409#
#SPJ11
A -2.0 nCnC point charge is located at (9.0 mm, 0), and a -19 nCnC point charge is located at (0, 9 mm). What is the magnitude of the net electric field at the origin?
Express your answer with the appropriate units.
What is the direction of the net electric field at the origin? Find the angle measured from the positive xx axis to the net electric field.
Express your answer in degrees.
The direction of the net electric field at the origin is at an angle of 87° with the negative x-axis.Charge, q1 = -2.0 nC = -2.0 × 10⁻⁹ C, Charge, q2 = -19 nC = -19 × 10⁻⁹ C, Position vector, r1 = (9.0 mm, 0) = (9.0 × 10⁻³ m, 0), Position vector, r2 = (0, 9.0 mm) = (0, 9.0 × 10⁻³ m).
Let E1 be the electric field due to charge q1 and E2 be the electric field due to charge q2 at the origin. Magnitude of the net electric field at the origin.
The net electric field at the origin, E = E1 + E2.
Electric field due to charge q1, E1 = (1/4πε₀) * q1/ r1², where ε₀ is the permittivity of free space.
We have, q1 = -2.0 nC = -2.0 × 10⁻⁹ C, r1 = (9.0 × 10⁻³ m, 0)Electric field due to charge q1,E1 = (1/4πε₀) * q1/ r1² ...(1)
Electric field due to charge q2, E2 = (1/4πε₀) * q2/ r2².
We have, q2 = -19 nC = -19 × 10⁻⁹ C, r2 = (0, 9.0 × 10⁻³ m)Electric field due to charge q2,E2 = (1/4πε₀) * q2/ r2² ...(2)
As the two charges are negative, the electric field at the origin due to charge q1 and q2 are directed towards the origin. Therefore, both electric fields E1 and E2 are negative.
Net electric field at the origin,E = E1 + E2.
Putting the value of E1 and E2 in the equation of the net electric field at the origin,
E = (1/4πε₀) * q1/ r1² - (1/4πε₀) * q2/ r2² = (9 × [tex]10^9[/tex] N m²/C²) * [(q1/ r1²) - (q2/ r2²)]E = (9 × [tex]10^9[/tex] N m²/C²) * [(q1/ r1²) - (q2/ r2²)]E = (9 × [tex]10^9[/tex] N m²/C²) * [(-2.0 × 10⁻⁹ C/ (9.0 × 10⁻³ m)²) - (-19 × 10⁻⁹ C/ (9.0 × 10⁻³ m)²)]E = -7.06 × 10⁵ N/C.
Therefore, the magnitude of the net electric field at the origin is 7.06 × 10⁵ N/C.
Direction of the net electric field at the origin.
The two electric fields E1 and E2 are acting along the x-axis and y-axis, respectively.
Therefore, the net electric field at the origin will be the vector sum of these two electric fields.
The angle measured from the positive x-axis to the net electric field can be found by using the relation tanθ = E2/E1θ = tan⁻¹(E2/E1).
Putting the values of E1 and E2 in the equationθ = tan⁻¹(-19/2).
Therefore, the angle measured from the positive x-axis to the net electric field is -87°.
Hence, the direction of the net electric field at the origin is at an angle of 87° with the negative x-axis.
Learn more about electric field here ;
https://brainly.com/question/11482745
#SPJ11
The magnitude of Earth's magnetic field is about 0.5 G near Earth's surface. What is the maximum possible magnetic force on an electron with kinetic energy of 1keV? Also, compare with the gravitational force on the electron.
The gravitational force is 7.28*10⁻⁴⁷ N. The magnetic force on an electron with kinetic energy of 1 keV is much greater than its gravitational force.
The maximum possible magnetic force on an electron with kinetic energy of 1 keV can be calculated using the following formula:
( F = qvB )
where ( F ) is the magnetic force, ( q ) is the charge of the electron, ( v ) is the velocity of the electron, and ( B ) is the magnetic field strength.
The charge of an electron is [tex]( -1.6 \times 10^{-19} )[/tex]coulombs, and the velocity of an electron with kinetic energy of 1 keV can be calculated using the following formula:
[tex]( K.E. = \frac{1}{2}mv^2 )[/tex]
where ( K.E. ) is the kinetic energy, ( m ) is the mass of the electron, and ( v ) is the velocity of the electron.
The mass of an electron is ( 9.11 \times 10^{-31} ) kg.
Using these values and the given magnetic field strength of 0.5 G, we get:
[tex]( v = \sqrt{\frac{2K.E.}{m}} = \sqrt{\frac{2(1\text{ keV})(1.6\times10^{-19}\text{ C})}{9.11\times10^{-31}\text{ kg}}} = 5.93\times10^6\text{ m/s} )( F = qvB = (-1.6\times10^{-19}\text{ C})(5.93\times10^6\text{ m/s})(0.5\text{ G}) = -4.74\times10^{-14}\text{ N} )[/tex]
Therefore, the maximum possible magnetic force on an electron with kinetic energy of 1 keV is ( -4.74\times10^{-14}\text{ N} ).
To compare this with the gravitational force on the electron, we can use the following formula:
[tex]F_g = G\frac{m_1m_2}{r^2} )[/tex]
where[tex]( F_g )[/tex] is the gravitational force, ( G ) is the gravitational constant (( [tex]6.67\times10^{-11}\text{ N}\cdot\text{m}2/\text{kg}2 ))[/tex], [tex]( m_1 ) and ( m_2 )[/tex] are the masses of the two objects (in this case, the electron and Earth), and ( r ) is the distance between them.
The mass of Earth is approximately[tex]( 5.97\times10^{24} )[/tex] kg, and the radius of Earth is approximately 6,371 km (or 6,371,000 m).
Using these values and the mass of an electron[tex](( 9.11\times10^{-31} ) kg),[/tex] we get:
[tex]( F_g = G\frac{m_1m_2}{r^2} = (6.67\times10^{-11}\text{ N}\cdot\text{m}2/\text{kg}2)\frac{(9.11\times10^{-31}\text{ kg})(5.97\times10^{24}\text{ kg})}{(6,371,000\text{ m})^2} = 7.28\times10^{-47}\text{ N} )[/tex]
Therefore, we can see that the magnetic force on an electron with kinetic energy of 1 keV is much greater than its gravitational force.
To know more about magnetic force
https://brainly.com/question/26257705
#SPJ4
The drawing shows three particles far away from any other objects and located on a straight line. The masses of these particles are m
A
=375 kg,m
g
=504 kg, and m
C
=104 kg. Take the positive direction to be to the right. Find the net gravitational force, including sign, acting on (a) particle A
,
(b) particle B, and (c) particle C. (a) Number Units (b) Number Units (c) Number Units eTextbook and Media Attempts: 0 of 4 used Using multiple attempts will impactyour score: 50 s score reduction atter attempt 3
We cannot calculate the net gravitational forces on particles A, B, and C without the values for the distances between the particles.
To determine the net gravitational force acting on each particle, we need to consider the gravitational attraction between each pair of particles.
(a) Net gravitational force on particle A:
The net gravitational force on particle A is the sum of the gravitational forces between A and particles B and C. The gravitational force between two objects can be calculated using Newton's law of universal gravitation:
F = G * (m1 * m2) / r^2
where F is the gravitational force, G is the gravitational constant, m1 and m2 are the masses of the objects, and r is the distance between the objects.
Let's calculate the net gravitational force on particle A:
F_A = F_AB + F_AC
F_AB = G * (m_A * m_B) / r_AB^2
F_AC = G * (m_A * m_C) / r_AC^2
Substituting the given values:
m_A = 375 kg
m_B = 504 kg
m_C = 104 kg
r_AB = distance between particles A and B (not provided)
r_AC = distance between particles A and C (not provided)
Without the values for the distances between the particles, we cannot determine the net gravitational force on particle A.
(b) Net gravitational force on particle B:
The net gravitational force on particle B is the sum of the gravitational forces between B and particles A and C:
F_B = F_BA + F_BC
Using the same formula as above, we substitute the respective values:
m_B = 504 kg
m_A = 375 kg
m_C = 104 kg
r_BA = distance between particles B and A (not provided)
r_BC = distance between particles B and C (not provided)
Without the values for the distances between the particles, we cannot determine the net gravitational force on particle B.
(c) Net gravitational force on particle C:
The net gravitational force on particle C is the sum of the gravitational forces between C and particles A and B:
F_C = F_CA + F_CB
Using the same formula as above, we substitute the respective values:
m_C = 104 kg
m_A = 375 kg
m_B = 504 kg
r_CA = distance between particles C and A (not provided)
r_CB = distance between particles C and B (not provided)
Without the values for the distances between the particles, we cannot determine the net gravitational force on particle C.
In conclusion, we cannot calculate the net gravitational forces on particles A, B, and C without the values for the distances between the particles.
To learn more about force
https://brainly.com/question/12785175
#SPJ11
Explain the importance of the following aspect of groundwater studies; The Sand Tank Model in EWS laboratory, focused groundwater recharge zones, Flow characteristics method and purging borehole. Im each paragraph make a point, explain the point and then give an example.
Groundwater studies employ various techniques and methodologies to understand and manage groundwater resources effectively. The sand tank model in EWS laboratory, focused groundwater recharge zones, flow characteristics method, and purging boreholes are important aspects of groundwater studies.
Explanation:
1. The sand tank model in EWS laboratory:
The sand tank model is a scaled-down representation of an aquifer system used in laboratory experiments to simulate groundwater flow and contaminant transport. It provides valuable insights into the behavior and dynamics of groundwater, allowing researchers to study various phenomena and test different scenarios. For example, by injecting dye into the model, researchers can observe how contaminants move through the porous media, aiding in the understanding of groundwater contamination and remediation strategies.
2. Focused groundwater recharge zones:
Identifying and understanding groundwater recharge zones is crucial for sustainable groundwater management. Recharge zones are areas where water infiltrates into the ground and replenishes the groundwater reservoir. By focusing on these specific zones, hydrogeologists can prioritize conservation efforts, implement appropriate land-use practices, and optimize artificial recharge techniques. For instance, through the analysis of geological and hydrological data, such as soil permeability and rainfall patterns, hydrogeologists can identify areas where natural recharge is high and take measures to protect and enhance these zones.
3. Flow characteristics method:
The flow characteristics method is a technique used to determine the hydraulic conductivity and permeability of aquifers. It involves analyzing the response of groundwater levels to pumping or injection tests. By monitoring changes in water levels over time and applying mathematical models, hydrogeologists can estimate the properties of the aquifer, such as its ability to transmit and store water. This information is crucial for understanding groundwater flow patterns, designing well fields, and evaluating the potential for groundwater extraction. For example, conducting a pumping test in an aquifer can provide data on its flow rate and hydraulic conductivity, aiding in the development of effective groundwater management strategies.
4. Purging boreholes:
Purging boreholes involves removing stagnant water and sediments from the well before conducting groundwater sampling or monitoring. This process ensures that the collected water samples represent the true characteristics of the aquifer and eliminates the influence of stagnant water that may have different chemical or physical properties. Purging boreholes is essential to obtain accurate data for groundwater quality assessment and monitoring programs. For instance, if a borehole has not been purged adequately, the water sample collected may not reflect the actual groundwater composition, leading to misleading interpretations and incorrect decisions regarding water resource management.
Learn more about physical properties here:
https://brainly.com/question/18327661
#SPJ11
A ball thrown vertically upward is caught by the thrower after 3.2 seconds. Find: a) The initial velocity of the ball. b) The maximum height it reaches.
The initial velocity of the ball is 31.36 m/s. The maximum height reached by the ball is approximately 50.176 meters. We can use the equations of motion for free fall.
To find the initial velocity and maximum height of a ball thrown vertically upward and caught after a certain time, we can use the equations of motion for free fall.
Given:
Total time of flight (t) = 3.2 seconds
a) Finding the initial velocity (u):
Using the equation for the vertical motion of the ball:
v = u + gt
At the maximum height, the final velocity (v) will be zero. Therefore:
0 = u + (-9.8 m/s^2) * 3.2 s
Solving for u:
u = 9.8 m/s * 3.2 s
u = 31.36 m/s
Therefore, the initial velocity of the ball is 31.36 m/s.
b) Finding the maximum height (h):
Using the equation for the vertical displacement of the ball:
h = ut + (1/2)gt^2
Substituting the values:
h = (31.36 m/s) * (3.2 s) + (1/2) * (-9.8 m/s^2) * (3.2 s)^2
Calculating:
h = 100.352 m - 50.176 m
h ≈ 50.176 m
Therefore, the maximum height reached by the ball is approximately 50.176 meters.
To learn more about velocity click here
https://brainly.com/question/28395671
#SPJ11
Sharmeka is pushing a grocery cart down an aisle in Kroger at 2.25 m/s when she suddenly has to stop due cereal boxes falling off of the shelf and onto the floor. It takes her 1.12 m to react and come to a full stop. Calculate her acceleration during this time.
The acceleration due to sudden stoppage is -0.03 m/s².
We will be using one of the equation of motion to calculate Sharmeka's acceleration. The specific formula to be used is -
v = u + at, where a is acceleration, t is time and v and u are final and initial velocity. Since she stops, here final velocity will be zero.
Keep the values in formula to find the acceleration
0 = 2.25 + a × 1.12 × 60
As 1 minute is 60 seconds
0 = 2.25 + 67.2a
67.2a = -2.25
a = -2.25/67.2
a = -0.03 m/s²
The negative sign in the result indicates deceleration. Hence the acceleration is -0.03 m/s².
Learn more about acceleration -
https://brainly.com/question/460763
#SPJ4
In chiaroscuro, the highlight is directly next to the
Choose matching definition
1
scale
2
motion
3
light
4
warm
In chiaroscuro, the highlight is directly next to the (3) Light. Chiaroscuro is an artistic technique commonly used in visual arts, particularly in painting and drawing.
It involves the use of contrasting light and dark values to create a sense of depth and volume in a two-dimensional artwork. The term "chiaroscuro" originates from the Italian words "chiaro" (light) and "scuro" (dark).
In this technique, the highlight refers to the area of the artwork that receives the most intense and direct light. It is usually positioned adjacent to the areas of the artwork that are in shadow or have darker values.
The contrast between light and dark creates a sense of three-dimensionality and emphasizes the volume and form of the depicted objects or figures.
Therefore, (3) Light is the correct answer.
To know more about chiaroscuro refer here :
https://brainly.com/question/30414123#
#SPJ11
red sunsets are due to light of lower frequencies that
Red sunsets are due to light of lower frequencies that are more capable of making their way through the Earth’s atmosphere. Sunsets take on different colors and shades because of the way that sunlight interacts with the Earth's atmosphere.
When the sunlight passes through the atmosphere, molecules and small particles in the air scatter different colors of light. This leads to colorful skies at sunrise and sunset. When the sun is low on the horizon, the sunlight must pass through more of the Earth’s atmosphere before reaching the observer's eye.
At sunrise or sunset, the light that reaches the observer's eye has a longer path through the atmosphere than light at noon. The Earth's atmosphere scatters blue light more efficiently than it scatters the lower-frequency colors. This scattering effect sends more blue light away from the viewer's line of sight. This makes the sky look blue. When sunlight passes through the atmosphere, molecules and small particles in the air scatter different colors of light.
When the sun is low on the horizon, the sunlight must pass through more of the Earth’s atmosphere before reaching the observer's eye. At sunrise or sunset, the light that reaches the observer's eye has a longer path through the atmosphere than light at noon. The Earth's atmosphere scatters blue light more efficiently than it scatters the lower-frequency colors. This scattering effect sends more blue light away from the viewer's line of sight, making the sky look blue
In conclusion, Red sunsets are due to light of lower frequencies that are more capable of making their way through the Earth’s atmosphere. Sunsets take on different colors and shades because of the way that sunlight interacts with the Earth's atmosphere.
To know more about frequencies, visit:
https://brainly.com/question/254161
#SPJ11
A mass m = 2.0 kg is attached to a spring and resting on a frictionless surface as in the figure. The mass is displaced from its equilibrium position and released. The oscillation of the mass is given by the equation: , where x is measured in cm and t in seconds.
-What is the total energy of the mass?
-What is the kinetic energy of the mass at t=1s?
-What is the potential energy of the mass at t=1s?
-What is the frequency of oscillation of the mass?
-What is the time period of oscillation of the mass?
-What is the acceleration in ()of the particle at t = 3 sec?
-What is the speed of the particle at t = 5 sec?
-What is the magnitude of the displacement of the particle at t = 5 sec?
The total energy of the mass is constant, determined by the amplitude of the oscillation, and is the sum of kinetic and potential energy.
The total energy of the mass is constant and is determined by the amplitude of the oscillation. The kinetic energy of the mass at t=1s can be calculated using the equation KE = (1/2)mv^2, where m is the mass and v is the velocity.
The potential energy of the mass at t=1s can be determined as the difference between the total energy and the kinetic energy.
The frequency of oscillation can be calculated using the equation f = 1/T, where T is the time period of oscillation. The time period of oscillation can be determined using the equation T = 2π/ω, where ω is the angular frequency.
The acceleration of the particle at t=3s can be calculated using the equation a = -ω^2x, where x is the displacement from the equilibrium position.
The speed of the particle at t=5s can be calculated as the magnitude of the velocity, v. The magnitude of the displacement of the particle at t=5s can be determined as the amplitude of the oscillation, A.
Learn more about potential energy from the given link:
https://brainly.com/question/24284560
#SPJ11.
Bill is standing on the top of a 60 m tall building. He throws a ball downward with the speed of 15 m/s. At the same time Jennifer, who is standing on the ground, throws a second ball upward with the same speed. (a) How high above the ground will the two balls meet? (b) What are their velocities? (c) Which ball does hit the ground first? Explain. (d) Plot velocity and position versus time graphs for the two balls.
Bill and Jennifer throw a ball at the same speed of 15 m/s from two different heights. The height where the two balls meet is around 71.51068 m. The velocity for Bill's ball and for Jennifer's ball is -4.012 m/s.
(a) To determine how high above the ground the two balls will meet, we can find the time it takes for each ball to reach its highest point and then calculate the total distance traveled by each ball.
For Bill's ball:
Using the equation for vertical displacement, we can calculate the time it takes for the ball to reach its highest point:
y = y₀ + v₀t - (1/2)gt²
0 = 60 + 15t - (1/2)(9.8)t²
Solving this quadratic equation, we find t ≈ 1.94 seconds.
Substituting this time back into the equation for vertical displacement, we can determine the height above the ground where the balls meet:
y = 60 + 15(1.94) - (1/2)(9.8)(1.94)²
with 15(1.94) = 29.1
(1/2)(9.8)(3.7636) = 17.58932
Substituting these values back into the expression for y:
y = 60 + 29.1 - 17.58932
y = 60 + 29.1 - 17.58932
= 89.1 - 17.58932
= 71.51068
Therefore, the height above the ground where the two balls meet is approximately 71.51068 meters.
For Jennifer's ball:
Since Jennifer throws the ball upward with the same initial speed, the time it takes for the ball to reach its highest point is also approximately 1.94 seconds. Therefore, the height above the ground where the balls meet is the same.
(b) The velocities of the balls at the point of meeting can be found using the equation:
v = v₀ - gt
For Bill's ball:
v = 15 - 9.8(1.94)
9.8 * 1.94 = 19.012
v = 15 - 19.012
v = 15 - 19.012
= -4.012 m/s (negative sign indicates the upward direction)
Therefore, the velocity of the ball thrown by Bill at the point of meeting is approximately -4.012 m/s
For Jennifer's ball:
v = -15 - 9.8(1.94)
v = -4.2 m/s
(c) To determine which ball hits the ground first, we need to compare their total flight times. Since the height above the ground where the balls meet is the same, the ball thrown by Jennifer will take longer to reach the ground because it has to cover the additional distance from the meeting point to the ground.
d) The graph in image below shows that initially, the ball is at the top of the 60-meter building. As time progresses, the ball moves downward, crossing the meeting point, and continues to fall towards the ground.
Learn more about vertical displacement here:
https://brainly.com/question/3333112
#SPJ11
A 47 m copper wire is laid at a temperature of 15°C.
What is its change in length when the temperature increases to
49°C?
Take
α
αcopper = 1.67×10-5 (C°)-1
The change in length of the copper wire when the temperature increases from 15°C to 49°C is approximately 0.0267 meters (or 26.7 mm).
To calculate the change in length of a copper wire when the temperature increases, we can use the formula:
ΔL = α * L₀ * ΔT
Where:
ΔL is the change in length
α is the coefficient of linear expansion for copper
L₀ is the initial length of the wire
ΔT is the change in temperature
Given:
α_copper = 1.67 × 10^(-5) (°C)^(-1) (coefficient of linear expansion for copper)
L₀ = 47 m (initial length of the wire)
ΔT = (49°C - 15°C) = 34°C (change in temperature)
Substituting these values into the formula:
ΔL = (1.67 × 10^(-5) (°C)^(-1)) * (47 m) * (34°C)
ΔL = 1.67 × 10^(-5) * 47 * 34 m
ΔL = 1.67 × 10^(-5) * 1598 m
ΔL ≈ 0.0267 m
Therefore, the change in length of the copper wire when the temperature increases from 15°C to 49°C is approximately 0.0267 meters (or 26.7 mm).
Learn more about linear expansion here:
https://brainly.com/question/32547144
#SPJ11
Water is to be transported at a rate of 2 mº/s in uniform flow in an open channel with walls having a Manning's coefficient of 0.016, the bottom slope is 0.001. Determine the best cross section shape of the channel if cross section is (i) Rectangular(2 72 marks) (ii) Trapezoidal
While a rectangular channel is simpler to construct, a trapezoidal channel often offers better hydraulic efficiency for transporting water at the desired flow rate.
To determine the best cross-section shape of the channel for transporting water at a rate of 2 m³/s in uniform flow, we can compare the efficiency of two common cross-section shapes: rectangular and trapezoidal.
(i) Rectangular Cross-Section:
In a rectangular channel, the cross-section shape is a simple rectangle with a constant width (b) and depth (h). To calculate the hydraulic radius (R) of the channel, we use the formula R = (b * h) / (b + 2h). Using Manning's equation for uniform flow Q = (1/n) * A * R^(2/3) * S^(1/2), where Q is the flow rate, A is the cross-sectional area, n is Manning's coefficient, R is the hydraulic radius, and S is the slope of the channel bottom. By rearranging the equation, we can solve for the cross-sectional area A = (Q * (b + 2h)) / (n * R^(2/3) * S^(1/2)). We can then optimize the channel dimensions to achieve the desired flow rate.
(ii) Trapezoidal Cross-Section:
In a trapezoidal channel, the cross-section shape has a wider bottom and sloping sides. It offers a more efficient flow because the wider bottom allows for a larger cross-sectional area and reduced flow depth for the same flow rate. By adjusting the bottom width (b), side slope angle (θ), and flow depth (h), we can optimize the channel dimensions to achieve the desired flow rate.
The best cross-section shape between rectangular and trapezoidal depends on several factors, including available space, construction feasibility, and specific requirements of the project. While a rectangular channel is simpler to construct, a trapezoidal channel often offers better hydraulic efficiency for transporting water at the desired flow rate. Engineers consider various factors, including cost, available space, and hydraulic performance, to determine the most suitable cross-section shape for a particular application.
Learn more about hydraulic radius here:
https://brainly.com/question/33339494
#SPJ11
Consider two objects of masses m 6.719 kg and my-2.525 kg The first mass (m) is traveling along the negative y-axis at 51.33 km/hr and strikes the second stationary mass ma locking the two man together amant 2) (5 Points) What is the velocity of the first mass before the collision? Marke 30.00 > m/s Ta 8Points) What is the velocity of the second man before the collision? >m/s (Point) The final velocity of the two masses can be calculated using the formula number: (Note use the formita-sheet given in the introduction section) 15 Points) What is the final velocity of the two masses? By s (Pints) Choose the correct answer 1) (4 Points) What is the total initial kinetic energy of the two masses? (P) What is the total final kinetic energy of the two masses? 10CP) Howth of the mechanical energy is lost due to this collision Mar 12:08 P Flag question Problem 1 (30 points) Consider two objects of masses m₁= 6.719 kg and m₂ = 2.525 kg. The first mass (m₁) is traveling along the negative y- axis at 51.33 km/hr and strikes the second stationary mass m₂, locking the two masses together. a) (5 Points) What is the velocity of the first mass before the collision? m1 H > m/s b) (3 Points) What is the velocity of the second mass before the collision? m2 m/s c) (1 Point) The final velocity of the two masses can be calculated using the formula number: (Note: use the formula-sheet given in the introduction section) d) (5 Points) What is the final velocity of the two masses? V₁=< > m/s e) (4 Points) Choose the correct answer: e) (4 Points) Choose the correct answer: kinetic The final momentum of the system is less than the initial momentum of the system inetic The final momentum of the system is greater than the anical initial momentum of the system The final momentum of the system is equal to the initial momentum of the system + Previous page 15 < Next page f) (4 Points) What is the total initial kinetic energy of the two masses? Ki= J g) (5 Points) What is the total final kinetic energy of the two masses? Kf= J h) (3 Points) How much of the mechanical energy is lost due to this collision? AEint= J
a) The velocity of the first mass before the collision = -51.33 km/hr (1000 m/km) / (60 60 s/hr) = -14.26 m/sb) The velocity of the second mass before the collision = 0 m/sc) Inelastic collision formula:
(m1 v1) + (m2 v2) = (m1 + m2) vf Where m1 = 6.719 kg, m2 = 2.525 kg, v1 = -14.26 m/s, v2 = 0 m/s and vf is the final velocity.By plugging these values in the above equation we get the final velocity, vf = (m1 v1 + m2 v2) / (m1 + m2)= (-6.719 kg 14.26 m/s + 2.525 kg 0 m/s) / (6.719 kg + 2.525 kg) = -10.74 m/s (answer)d) The final velocity of the two masses is -10.74 m/s.
e) The final momentum of the system is less than the initial momentum of the system (answer) because the two masses are moving in opposite directions, and their velocities have opposite signs. Therefore, their momenta also have opposite signs. Since the final velocity of the two masses is negative, the final momentum is negative, which means it has a smaller magnitude than the initial momentum, which was also negative.
f) The total initial kinetic energy of the two masses is calculated as follows:
KEi = (1/2) m1 v1^2 + (1/2) m2 v2^2= (1/2) 6.719 kg (-14.26 m/s)^2 + (1/2) 2.525 kg (0 m/s)^2= 1392.81 J (answer)g) The total final kinetic energy of the two masses is calculated as follows: KEf = (1/2) (m1 + m2) vf^2= (1/2) (6.719 kg + 2.525 kg) (-10.74 m/s)^2= 437.38 J (answer)h) The mechanical energy lost due to this collision is calculated as the difference between the initial kinetic energy and the final kinetic energy. AEint = KEi - KEf= 1392.81 J - 437.38 J= 955.43 J (answer)
About CollisionA collision is a situation that occurs when two or more demands are made simultaneously on equipment that can only handle one at a time. It may refer to a collision domain, a physical network segment where data packets can "collide."
Learn More About Collision at https://brainly.com/question/12644900
#SPJ11
a homogenous soil column 40 cm heigh , has a cross-sectional area of 100 cm2 and 10 cm water continuously ponded on it. if steady-state volume rate Q, through the soil is 1000cm3/hr downwards, determine the following;
a)steady-state flux through the soil
b)Hydraulic conductivity of the soil
The answers are a) 10cm/hr; b) -40cm/hr. Height of soil column (H) = 40 cm, Cross-sectional area (A) = 100 cm², Water ponded on soil = 10 cm, Volume rate (Q) = 1000 cm³/hr, Downward direction = Steady-state
a) Steady-state flux through the soil is given by the Darcy's law. Darcy's law states that the volume flow rate per unit area is directly proportional to the hydraulic gradient. That is,
Q/A = - K dh/dl Where Q = Volume flow rate, A = Cross-sectional area, K = Hydraulic conductivity, dh/dl = Hydraulic gradient, dh/dl = Change in height/change in length, dh/dl = H/L = 10/40 = 0.25
Substituting the given values, Q/A = - K dh/dl⇒K = - Q/(A dh/dl)⇒K = - 1000 / (100 × 0.25)⇒K = - 4000/100 = - 40 cm/hr
Steady-state flux through the soil = Q/A⇒1000/100⇒10 cm/hr
b) Hydraulic conductivity of the soil can be determined using Darcy's law.
K = - Q/(A dh/dl)⇒K = - 1000/(100 × 0.25)⇒K = - 4000/100K = - 40 cm/hr
Therefore, hydraulic conductivity of the soil is -40 cm/hr.
Learn more about hydraulic conductivity here: https://brainly.com/question/16227436
#SPJ11
What kind of star is most likely to become a white-dwarf supernova? an O star a white dwarf star with a red giant binary companion a star like our Sun a pulsar
A white dwarf star with a red giant binary companion is most likely to become a white-dwarf supernova.
A supernova is an event in which a star, particularly a massive one, undergoes a catastrophic explosion, radiating an enormous amount of energy. When a star explodes, it briefly outshines an entire galaxy, ejecting up to 95% of its material in the form of a rapidly expanding shockwave. A white-dwarf supernova is a supernova that happens when a white dwarf star reaches the end of its life.
These stars are smaller and less massive than other types of stars, and they eventually run out of fuel and begin to cool down. When the temperature in the core of the star drops below a certain level, a thermonuclear reaction begins to take place, causing a massive explosion. A white dwarf star with a red giant binary companion is most likely to become a white-dwarf supernova.
You can learn more about Supernova at: brainly.com/question/32402054
#SPJ11
Electric field strength is defined as the _________ experienced
per unit charge.
A. Force
B. Current
C. Charge
D. Power
Electric field strength is defined as the force experienced per unit charge. The correct option is A.
It is a measure of the intensity of the electric field at a specific point in space. When a charged particle is placed in an electric field, it experiences a force due to the interaction between its charge and the electric field. The electric field strength at that point is defined as the force exerted on the particle per unit charge.
The electric field strength can be mathematically represented as E = F/Q, where E is the electric field strength, F is the force experienced by the charge, and Q is the magnitude of the charge. This equation demonstrates that the electric field strength is directly proportional to the force experienced by the charge and inversely proportional to the magnitude of the charge.
Therefore, the correct answer is A. Force. Electric field strength is a measure of the force experienced per unit charge in an electric field.
To know more about Electric field strength, refer to the link below:
https://brainly.com/question/32750938#
#SPJ11