Four kinds of rotational motion are as follows: 1) Uniform rotational motion, 2) Non-uniform rotational motion, 3) Oscillatory rotational motion, and 4) Precessional rotational motion.
Uniform rotational motion refers to the rotation of an object with a constant angular velocity. In this type of motion, the object covers equal angular displacements in equal intervals of time. An example of uniform rotational motion is a wheel rolling along a flat surface without any external forces acting upon it.
Non-uniform rotational motion occurs when an object rotates with a changing angular velocity. In this case, the object covers unequal angular displacements in equal intervals of time. An example of non-uniform rotational motion is a spinning top gradually slowing down due to the effects of friction and air resistance.
Oscillatory rotational motion involves the back-and-forth rotation of an object around a fixed axis. It follows a repetitive pattern, where the object oscillates between two extreme positions. An example of oscillatory rotational motion is a pendulum swinging back and forth.
Precessional rotational motion refers to the motion of a spinning object whose axis of rotation itself undergoes a circular motion. The spinning object exhibits both its own spin and the rotation of its axis. A classic example of precessional rotational motion is the motion of a spinning top as it gradually tilts and changes the direction of its axis.
Learn more about rotational motion from the given link:
https://brainly.com/question/30193887
#SPJ11.
Determine the one or more conditions required for the linear momentum in a system to have reached steady state : A. There are no external forces but mass can be transported into or out of the system B. the system has constant acceleration and constant mass C. No mass is transported into or out of the system but external forces can be applied D. the system has constant velocity and constant mass The rate form of the conservation of linear momentum reduces to Newton's second law under what condition(s): Select one or more of the answers below A. Min = 0 B. Mout = 0 oc. Fnet = 0 D.ag=0 (G refers to the center of mass) E. m sys=0
C. No mass is transported into or out of the system but external forces can be applied
In steady state, the system reaches a balance where the mass within the system remains constant, but external forces can still act on the system.
The rate form of the conservation of linear momentum reduces to Newton's second law under the condition(s):
D. Fnet = 0 (Net external force acting on the system is zero)
When the net external force acting on the system is zero, the rate form of the conservation of linear momentum reduces to Newton's second law, which states that the net force on an object is equal to its mass multiplied by its acceleration.
To learn more about mass
https://brainly.com/question/86444
#SPJ11
This inventor co-created the film Fred Ott's Sneeze,which was one of the first American movies.
A) William Faulkner
B) Thomas Edison
C) Albert Einstein
D) Robert Fulton
E) Alexander Graham Bell
The inventor who co-created the film Fred Ott's Sneeze, which was one of the first American movies was Thomas Edison. So option B is correct.
Thomas Edison, along with his team at the Edison Manufacturing Company, co-created the film titled "Fred Ott's Sneeze" in 1894. It is considered one of the earliest American motion pictures. The film features Fred Ott, an employee of Edison, sneezing and was a short, silent film that lasted just a few seconds. Thomas Edison was a prolific inventor and played a crucial role in the early development of motion pictures and filmmaking technology.Therefore option B is correct.
To learn more about Thomas Edison visit: https://brainly.com/question/28888370
#SPJ11
Pressure of a oil ( specific gravity = 0.86) at any section of a
pipe is 2 bar. Pressure head is
1.
23.71 m
2.
2 m
3.
20 m
4.
20.39 m
Pressure of a oil ( specific gravity = 0.86) at any section of a pipe is 2 bar. Pressure head is 23.71 m (Option A).
The pressure head is the vertical distance that a fluid column would rise due to the pressure at a given point. It is calculated by dividing the pressure by the product of the acceleration due to gravity (g) and the specific weight of the fluid (γ).
Let's assume the density of water is 1000 kg/m³. The density of the oil can be calculated as follows:
Density of oil = Specific gravity * Density of water = 0.86 * 1000 kg/m³ = 860 kg/m³
Now, to calculate the pressure head, we need to convert the pressure from bar to pascals (Pa) since pressure is typically measured in SI units.
1 bar = 100,000 Pa
Given that the pressure at the section of the pipe is 2 bar, the pressure can be converted to pascals as follows:
Pressure = 2 bar = 2 * 100,000 Pa = 200,000 Pa
Next, we can calculate the pressure head using the formula:
Pressure head = Pressure / (Density of oil * Acceleration due to gravity)
Acceleration due to gravity (g) is approximately 9.8 m/s².
Pressure head = 200,000 Pa / (860 kg/m³ * 9.8 m/s²) ≈ 23.71 meters
Therefore, the correct answer is 23.71 m.
Learn more about Pressure head here:
https://brainly.com/question/30450960
#SPJ11
Physical units in mechanics are usually some combination of the dimensions time T, mass M, and length L. Consider the physical quantities m,r,v,a, and t with dimensions [m]=M,[r]=L,[v]=LT−1 ,[a]=LT ^−2 , and [t]=T. Enter the dimensional expression of the quantity on the right-hand side of each equation. Your answers may contain only M, L, T, and exponents. Assume that each of the following equations is dimensionally consistent. L 0 =mvr [L1 W=mar k=− rma
The dimensional expressions for the quantities on the right-hand side of the given equations are ML²T⁰, ML²T⁻¹, and MLT⁻², corresponding to different physical quantities involved in the equations.
Physical quantities are m, r, v, a, and t with dimensions [m] = M, [r] = L, [v] = LT⁻¹, [a] = LT⁻², and [t] = T. The dimensional expression of the quantity on the right-hand side of each equation is given below:
L0 = mvr
where [L0] = L1[L] = [M]a[L]b[T]c = MaLbTc
By equating the dimensions on both sides, we get
LHS = RHS.
LHS = L0 = L¹
RHS
mvr = [M][L][LT⁻¹] = MaL²T⁻¹
Comparing the exponents of M, L, and T on both sides, we get
M : 1 = aL : 2 = bT : -1 + 1 = c⇒ a = 1, b = 2, and c = 0.
So, the dimensional expression of the quantity on the right-hand side of L0 = mvr is MaL²T⁰ = ML²T⁰W = mar
where [W] = [F][d] = MLT⁻²LT = ML²T⁻¹
By equating the dimensions on both sides, we get
LHS = RHS.
LHS = W = ML²T⁻¹
RHS
mar = [M][LT⁻²][L] = ML²T⁻¹
Comparing the exponents of M, L, and T on both sides, we get
M : 1 = 1
L : 2 = 1
T : -1 - 2 = -3⇒ the dimensional expression of the quantity on the right-hand side of W = mar is ML²T⁻¹.
K = -rma
By equating the dimensions on both sides, we get
LHS = RHS.
LHS = K = [M][L²][T⁻²]
RHS
-rma = -[L][M][T⁻²] = MLT⁻²
Comparing the exponents of M, L, and T on both sides, we get
M : 1 = 1
L : 2 = -1
T : -2 = -2⇒ the dimensional expression of the quantity on the right-hand side of K = -rma is MLT⁻².
Hence, the dimensional expression of the quantity on the right-hand side of each equation is
ML²T⁰, ML²T⁻¹, and MLT⁻².
To know more about dimensional expression, refer to the link below:
https://brainly.com/question/32658827#
#SPJ11
A motorcycle is traveling up one side of a hill and down the other side. The crest of the hill is a circular arc with a radius of 59.7 m. Determine the maximum speed that the cycle can have while moving over the crest without losing contact with the road. v=
Let v be the maximum speed that the motorcycle can have while moving over the crest without losing contact with the road.
Since the hill's crest is a circular arc with a radius of 59.7 m,
its weight W can be resolved into two components: a radial force W cos θ that is perpendicular to the road and a tangential force W sin θ that is parallel to the road.Let's now take a look at the forces acting on the motorcycle. The forces that act on the motorcycle are the gravitational force W, the centripetal force F, and the force of friction f.
As a result, the following equation can be used to find the maximum speed that the motorcycle can have while moving over the crest without losing contact with the road:
`Ff = mv²/r`where `m` is the mass of the motorcycle and `r` is the radius of the circular arc of the hill.
We can calculate the radial component of the weight as
`W cos θ = mg cos θ`, where `m` is the mass of the motorcycle and `g` is the acceleration due to gravity, which is approximately 9.8 m/s².
Substituting `W cos θ` and `W sin θ` into the equation for `Ff`, we have:
`f = µW cos θ` and `F = W sin θ`
Substituting these equations into the equation for `Ff`, we have:
`µmg cos θ = mv²/r - mg sin θ`
Simplifying this expression yields:
`v² = rg(µ cos θ - sin θ)`
Substituting the given values, we have:
`v² = (59.7 m)(9.8 m/s²)(0.9) = 522.7 m²/s²`
Therefore, the maximum speed that the cycle can have while moving over the crest without losing contact with the road is:
`v = sqrt(522.7 m²/s²) = 22.85 m/s`
To know more about gravitational force visit:
https://brainly.com/question/32609171
#SPJ11
A mass on a spring in SHM has amplitude A and period T. What is the total distance traveled by the mass after a time interval �?
A) 0
B) A/2
C) A
D) 2A
E) 4A
The total distance traveled by the mass after a time interval is 4A. Option E is correct.
In simple harmonic motion (SHM), the motion of the mass on a spring repeats itself periodically. The total distance traveled by the mass after a time interval τ depends on the relationship between τ and the period T.
The period T is the time it takes for one complete cycle of the motion. In other words, it is the time for the mass to go from one extreme (maximum displacement) to the other extreme and back again. During this time, the mass covers a distance of 2A, where A is the amplitude of the motion.
Now, let's consider the time interval τ. If τ is equal to or less than the period T, it means that the time interval falls within one complete cycle of the motion. In this case, the mass will cover a distance of 2A, as mentioned earlier.
However, if τ is greater than the period T, it means that the time interval spans multiple cycles of the motion. In each cycle, the mass covers a distance of 2A. Since there will be multiple cycles in the time interval τ, the total distance traveled by the mass will be greater than 2A.
The mass will travel a total distance of 4A after the time interval τ.
Therefore, Option E is correct.
Learn more about distance -
brainly.com/question/114551
#SPJ11
Each of the following statements about the electric field in a conductor at equilibrium was written by a different student. Select all hose that are physically correct. At equilibrium the electric field inside a polarized conductor due to the charges accumulated at the surface of the conductor is zero, so the net electric field inside the conductor is equal to the electric field due to charges in the surroundings. At equilibrium the electric field inside a polarized conductor due to the charges accumulated at the surface of the conductor is zero, and the electric field due to charges in the surroundings cannot penetrate the conductor, so the net electric field inside the conductor must be zero. At equilibrium the net electric field inside a conductor must be zero, because if it were not zero, there would be charge flow because the drift speed of the mobile charges is proportional the the net electric field. At equilibrium the net electric field inside a conductor must be zero, because the average drift speed of the mobile charges is
v
ˉ
=uE
net
, and the only way for
v
ˉ
to be zero is if E
net
=0. At equilibrium the electric field inside a conductor at equilibrium is zero because electric fields due to charges in the surroundings cannot penetrate the material of the conductor. At equilibrium the net electric field inside a conductor is zero because the conductor polarizes until the electric field inside the conductor due to charges at the surface is equal and opposite to the electric field due to charges in the surroundings.
At equilibrium the electric field inside a polarized conductor due to the charges accumulated at the surface of the conductor is zero, so the net electric field inside the conductor is equal to the electric field due to charges in the surroundings.
At equilibrium the electric field inside a polarized conductor due to the charges accumulated at the surface of the conductor is zero, and the electric field due to charges in the surroundings cannot penetrate the conductor, so the net electric field inside the conductor must be zero.
At equilibrium the net electric field inside a conductor must be zero, because the average drift speed of the mobile charges is v ˉ =uE net , and the only way for v ˉ to be zero is if E net =0. At equilibrium the net electric field inside a conductor is zero because the conductor polarizes until the electric field inside the conductor due to charges at the surface is equal and opposite to the electric field due to charges in the surroundings.
When an electric field is applied to a conductor, the free charges inside the conductor experience an electric force. The charges move and keep moving until the charge redistribution due to the motion of charges results in the elimination of the electric field inside the conductor.At this point, the redistribution of charges inside the conductor stops, and the conductor is said to have reached its electrostatic equilibrium.
During this equilibrium, there is no further movement of charges. Therefore, no current flows through the conductor.Therefore, only the following four statements are correct:At equilibrium the electric field inside a polarized conductor due to the charges accumulated at the surface of the conductor is zero, so the net electric field inside the conductor is equal to the electric field due to charges in the surroundings.
At equilibrium the electric field inside a polarized conductor due to the charges accumulated at the surface of the conductor is zero, and the electric field due to charges in the surroundings cannot penetrate the conductor, so the net electric field inside the conductor must be zero.
At equilibrium the net electric field inside a conductor must be zero, because the average drift speed of the mobile charges is v ˉ =uE net , and the only way for v ˉ to be zero is if E net =0.
At equilibrium the net electric field inside a conductor is zero because the conductor polarizes until the electric field inside the conductor due to charges at the surface is equal and opposite to the electric field due to charges in the surroundings.
Learn more about electric field here ;
https://brainly.com/question/11482745
#SPJ11
part 1 of 2 1. 6.40037 A 26 kg block slides down a frictionless slope which is at angle θ=28
∘
. Starting from 2. 3.95101 rest, the time to slide down is t=1.94 s. The acceleration of gravity is 9.8 m/s
2
. 3. 9.6721 4. 7.09055 5. 8.65783 6. 5.9233 7. 4.76882 What total distance s did the block slide? Answer in units of m. 8. 7.58912 Answer in units of m 9. 4.29407 10. 6.97977 1. 1.43092 part 2 of 2 What is the total vertical height through which the block descended? 2. 2.77438 Answer in units of m. 3. 4.06461 Answer in units of m 4. 2.65795 5. 3.26974 6. 2.97225 7. 2.02589 8. 4.23801 9. 2.09051 10. 3.0195
Given: A 26 kg block slides down a frictionless slope which is at angle θ=28 ∘ . Starting from rest, the time to slide down is t=1.94 s. The acceleration of gravity is 9.8 m/s2.The block slides down with uniform acceleration.
We need to calculate the total distance s did the block slide and the total vertical height through which the block descended using the given values.
1. Calculation of the distance s the block slide:
Let's use the third equation of motion,i.e. s = ut + 1/2 at²Where,u = initial velocity = 0a = acceleration = gs = ?t = 1.94 s
Putting the given values, we have:s = 0 × 1.94 + 1/2 × 9.8 × (1.94)²= 18.7717 m
Thus, the total distance s the block slide is 18.7717 m.
2. Calculation of the total vertical height:
Let's consider the right-angled triangle below: [tex]\frac{block}{height}[/tex]Thus, tan θ = opposite side / adjacent side
Hence, opposite side = adjacent side × tan θ= s × tan θ= 18.7717 × tan 28°= 10.1497 m
Thus, the total vertical height through which the block descended is 10.1497 m.
Hence, the options that answer the above two questions are:
Total distance s did the block slide = 18.7717 m.
Total vertical height through which the block descended = 10.1497 m.
To know more about acceleration visit :
https://brainly.com/question/12550364
#SPJ11
A radioactive nucleus has a half-life of 5×10^8 years. Suppose a sample of rock (say, in an asteroid) solidified right after the solar system formed. Then approximately what fraction of the radioactive element should be left in the rock today?
Given that a radioactive nucleus has a half-life of 5 × 108 years. Let's suppose that a sample of rock (say, in an asteroid) solidified right after the solar system formed.
Then we have to calculate the fraction of the radioactive element that should be left in the rock today.
Half-life (t₁/₂) of a radioactive substance is defined as the time taken by a substance to reduce to half its initial value.
This is given by the formula,N(t) = N₀(1/2)⁽ᵗ/ᵗ₁/₂⁾ Where,N(t) = Final quantity N₀ = Initial quantity t = Time elapsed t₁/₂ = Half-life period.
We know that the half-life (t₁/₂) of the radioactive nucleus is 5 × 108 years. Hence, the fraction of the radioactive element left can be calculated as follows:After the first half-life, the quantity of the radioactive element left would be N₀/2.
After the second half-life, it would be N₀/4 and so on.
Thus, the general formula for the quantity of the radioactive element left would be,N = N₀ (1/2)n Where n is the number of half-lives elapsed.
The fraction of the radioactive element left is given as,N/N₀ = (1/2)n.
Now, we can substitute the values in the above formula.
Let's suppose that one-half-life is 5 × 108 years. Then the age of the rock would be approximately 4.6 × 109 years (age of the Solar System).
Thus, the number of half-lives elapsed would be given by,n = (time elapsed)/(half-life)n = (4.6 × 109)/(5 × 108) = 9.2.
After 9.2 half-lives, the fraction of the radioactive element left would be,N/N₀ = (1/2)⁹.²≈ 0.00077 ≈ 7.7 × 10⁻⁴.
Thus, approximately 0.077% (7.7 × 10⁻⁴) of the radioactive element should be left in the rock today.
Learn more about asteroid here ;
https://brainly.com/question/18726579
#SPJ11
Mass =3M⊕
Radius =3R⊕
Gravity = ? F F⊕
1/9× Earth's
1/3 × Earth's
1/2 x Earth's
1× Earth's
Option 1 is correct. The gravity on a planet with a mass of 3 times that of Earth and a radius 3 times that of Earth would be 1/9th of Earth's gravity.
The force of gravity on a planet is determined by its mass and radius. According to Newton's law of universal gravitation, the force of gravity (F) between two objects is given by the equation [tex]F = (G * m1 * m_2) / r^2[/tex], where G is the gravitational constant, [tex]m_1[/tex] and [tex]m_2[/tex] are the masses of the two objects, and r is the distance between their centres.
In this case, we are comparing the gravity of a planet with a mass ([tex]m_2[/tex]) of 3 times that of Earth ([tex]M_\oplus[/tex]) and a radius (r) of 3 times that of Earth. Since the radius is directly proportional to the distance between the centres of the two objects, the value of [tex]r^2[/tex] would be [tex]3^2 = 9[/tex] times larger than Earth's radius.
As a result, the force of gravity on this planet would be [tex]1/9th (1/3^2)[/tex] of Earth's gravity, which is the first option given. Therefore, the correct answer is 1/9 × Earth's gravity.
Learn more about Newton's law of universal gravitation here:
https://brainly.com/question/9373839
#SPJ11
An astronaut at rest on Earth has a heartbeat rate of 69 beats/min. When the astronaut is traveling in a spaceship at 0.86c, what will this rate be as measured by an observer also in the ship and an observer at rest on Earth?
(a) an observer also in the ship (Need answers in beats/min)
(b) an observer at rest on Earth (Need answers in beats/min)
(a) As measured by an observer also in the ship, the heartbeat rate of the astronaut will be lower than 69 beats/min.
(b) As measured by an observer at rest on Earth, the heartbeat rate of the astronaut will still be 69 beats/min.
(a) According to time dilation in special relativity, time appears to pass more slowly for an object that is moving relative to an observer. In this case, when the astronaut is traveling in a spaceship at 0.86c (86% of the speed of light), the observer in the ship will measure a slower heartbeat rate for the astronaut compared to the rate observed on Earth. This is because time is dilated for the astronaut due to their high velocity.
To calculate the heartbeat rate as measured by the observer in the ship, we can apply the time dilation formula, which states that the observed time (t') is equal to the proper time (t) multiplied by the Lorentz factor (γ), where γ = 1 / sqrt(1 - v^2/c^2). In this case, v is the velocity of the spaceship and c is the speed of light.
(b) However, for an observer at rest on Earth, the heartbeat rate of the astronaut will still be 69 beats/min. This is because the time dilation effect is only experienced by the moving astronaut relative to the observer. From the perspective of the observer at rest on Earth, there is no relative motion between the observer and the astronaut, so there is no time dilation effect. Therefore, the observer on Earth will measure the same heartbeat rate of 69 beats/min as when the astronaut is at rest on Earth.
Learn more about time dilation here:
https://brainly.com/question/30493090
#SPJ11
1. [10 points] Read the following statements carefully and indicate True or False in your examination booklet: a) The static pressure is the pressure measured by a sensor moving at the same velocity as the fluid velocity. b) In a large, pressurized air tank, the stagnation pressure is larger than the static pressure at the same point. c) The flow across a normal shock wave is isentropic. d) e) Density p is constant across the expansion wave since it is an isentropic process. For a wedge of given deflection angle, wave angle of an attached oblique shock decreases as the Mach number decreases. f) A thinner airfoil will generally have a higher critical Mach number Mer compared to a thicker airfoil. g) Area ruling is a process in which the wing area of the airplane is changed to reduce supersonic drag. h) Supercritical airfoils achieve better performance by increasing Mer. i) An optimal shape for a re-entry vehicle moving at hypersonic Mach numbers is a sharp conical shape. j) Convective heating becomes less important than radiative heating as re-entry velocity increases.
The given question is based on true or false statements. Below mentioned are the answers for the given statements:
a) True
b) True
c) False
d) True
e) True
f) True
g) True
h) False
i) True
j) False
The given question is asking to identify the given statements which are true or false. All the statements are related to fluid mechanics and aerodynamics. Some of the important definitions are defined below:
Static pressure: The pressure of fluid when it is at rest is called static pressure.
Stagnation pressure: The pressure of a fluid when it is forced to stop moving is called stagnation pressure.
Isentropic: A process in which entropy remains constant is called isentropic.
Expansion wave: The wave generated when a supersonic flow slows down to a subsonic flow is called an expansion wave.
Wedge angle: The angle made by the forward edge of the wedge with the horizontal axis is called wedge angle. Wave angle: The angle between the direction of incoming flow and the line representing the wave's direction is called wave angle.
Critical Mach number: The Mach number at which the flow over the wing reaches supersonic velocity is called critical Mach number. The answers to the given statements are:
a) The static pressure is the pressure measured by a sensor moving at the same velocity as the fluid velocity. True
b) In a large, pressurized air tank, the stagnation pressure is larger than the static pressure at the same point. True
c) The flow across a normal shock wave is isentropic. False
d) Density p is constant across the expansion wave since it is an isentropic process. True
e) For a wedge of given deflection angle, wave angle of an attached oblique shock decreases as the Mach number decreases. True
f) A thinner airfoil will generally have a higher critical Mach number Mer compared to a thicker airfoil. True
g) Area ruling is a process in which the wing area of the airplane is changed to reduce supersonic drag. True
h) Supercritical airfoils achieve better performance by increasing Mer. False
i) An optimal shape for a re-entry vehicle moving at hypersonic Mach numbers is a sharp conical shape. True
j) Convective heating becomes less important than radiative heating as re-entry velocity increases. False
Hence, the correct answers for the given statements are True, True, False, True, True, True, True, False, True, and False.
To know more about Static pressure visit:
https://brainly.com/question/14873280
#SPJ11
The nucleus of 8 Be, which consists of 4 protons and 4 nectrons, is very unstable and spontaneously breaks into two alpha particies (helium nuclei, each consisting of 2 proeons and 2 . neutrons). (a) What is the force between the two alpha particles when they are 3.60×10−15 m apart? X. Youf response differs significantly from the correct answer. flework your solution from the beginning and check each step carefuily. N (b) What is the initial magnitude of the acceleration of the alpha particles due to this force? Note that the mass of an aipha particie is 4.0026 u. x Your response differs significantly from the correct answer, Rework your solution from the beginning and check each step carefully, mis?
The magnitude of the acceleration of the alpha particles is 3.5 × 10¹⁴ m/s².The charge on an alpha particle is 3.2 × 10⁻¹⁹ C. The distance between them is 2.3 × 10⁻¹² N.
(a) The electric force acting between two alpha particles is given as:F = k(q1q2)/r² where q1 and q2 are the charges of alpha particles, r is the separation between them, and k is Coulomb's constant.
The alpha particle consists of 2 protons, each having a charge of +1.6 × 10⁻¹⁹ C.
Therefore, the charge on an alpha particle is 2 × 1.6 × 10⁻¹⁹ C = 3.2 × 10⁻¹⁹ C.
The distance between them is 3.6 × 10⁻¹⁵ m.F = (9 × 10⁹ Nm²/C²) × [(3.2 × 10⁻¹⁹ C)²]/(3.6 × 10⁻¹⁵ m)²F = 2.3 × 10⁻¹² N
(b) The force between the two alpha particles causes an acceleration in them.
We can use the second law of motion to find the acceleration.a = F/m where m is the mass of one alpha particle.
The mass of an alpha particle is 4.0026 u = 6.65 × 10⁻²⁷ kg.a = (2.3 × 10⁻¹² N)/(6.65 × 10⁻²⁷ kg)a = 3.5 × 10¹⁴ m/s².
Therefore, the magnitude of the acceleration of the alpha particles is 3.5 × 10¹⁴ m/s².
Learn more about electric force here ;
https://brainly.com/question/20935307
#SPJ11
Star A has a magnitude of 6 and Star B has a magnitude of 15 . How much brighter is Star A than Star B? a. 1.5 b. 3815 c. 2.5 d. 2 e. 97.7 f. 0.0102 g. 6.25 h. 0.00164 i. 0.0002621 j. 5 k. 1526 I. 610 m. 0.0006554 n. 3.33 o. 0.16
The correct answer is Option f. Star A is 512.45 times brighter than Star B, or in other words, Star A is 0.0102 times as bright as Star B.
The magnitude of a star refers to its brightness as seen from Earth.
The magnitude scale is such that a difference of 1 magnitude unit is equal to a brightness difference of 2.512.
If one star has a magnitude of 6, and the other has a magnitude of 15, the difference in magnitude between them is 9 (15 - 6 = 9).
The brightness difference can be calculated using the magnitude difference between the two stars, using the following formula: Brightness difference = [tex]2.512^{(magnitude difference)}[/tex]
In this case, the magnitude difference between the two stars is 9.
So, the brightness difference can be calculated as:
[tex]Brightness difference = 2.512^9 = 512.45[/tex]
Therefore, Star A is 512.45 times brighter than Star B, or in other words, Star A is 0.0102 times as bright as Star B.
Hence, the correct answer is f. 0.0102.
For more questions on Star
https://brainly.com/question/25115985
#SPJ8
The distance between the first and the fifth minima of a single slit diffraction pattern is 0.35mm with the screen 40cm away from the slit when light of wavelength 550nm is used
(a) find the slit width
(b) Calculate the angle of the first diffraction minimum
(a) The slit width is approximately 0.025 mm.
(b) The angle of the first diffraction minimum is approximately 0.050°.
(a) To find the slit width, we can use the formula for the distance between minima in a single slit diffraction pattern:
d = λL / w
Where:
d = distance between minima
λ = wavelength of light
L = distance from slit to screen
w = slit width
Given:
d = 0.35 mm = 0.35 * 10^(-3) m
λ = 550 nm = 550 * 10^(-9) m
L = 40 cm = 40 * 10^(-2) m
Plugging in the values into the formula, we can solve for w:
0.35 * 10^(-3) = (550 * 10^(-9) * 40 * 10^(-2)) / w
Simplifying the equation, we find:
w ≈ 0.025 mm
Therefore, the slit width is approximately 0.025 mm.
(b) The angle of the first diffraction minimum can be calculated using the small angle approximation:
θ = λ / w
Given:
λ = 550 nm = 550 * 10^(-9) m
w = 0.025 mm = 0.025 * 10^(-3) m
Plugging in the values, we find:
θ ≈ (550 * 10^(-9)) / (0.025 * 10^(-3))
Simplifying the equation, we get:
θ ≈ 0.050°
Therefore, the angle of the first diffraction minimum is approximately 0.050°.
Learn more about slit width
brainly.com/question/13264398
#SPJ11
Observing that the ball rolls down the inclined plane, determine what the acceleration of the ball is as it rolls (assuming no friction) down the ramp. Note, you may be tempted to answer, "the acceleration of the ball is caused by the acceleration due to gravity which is 9.8 m/s?, however notice the ball does not fall vertically downward. Using the inclined plane as a right triangle, use trig to determine what the acceleration of the ball is. You will need to know the angle of inclination of the plane, which you can find using the images above.
To determine the acceleration of a ball as it rolls down an inclined plane (assuming no friction), we need to use trigonometry. We need to find the component of the force due to gravity that pulls the ball down the ramp. The acceleration of the ball is equal to this component divided by the mass of the ball.The angle of inclination of the plane is given as 30°.From the image, we see that the force due to gravity can be split into two components:
one parallel to the ramp (Fp) and one perpendicular to the ramp (Fn).The force parallel to the ramp (Fp) is given by Fp = mgsinθ, where m is the mass of the ball, g is the acceleration due to gravity, and θ is the angle of inclination of the plane.The force perpendicular to the ramp (Fn) is given by Fn = mgcosθ, where m is the mass of the ball, g is the acceleration due to gravity, and θ is the angle of inclination of the plane.The acceleration of the ball down the ramp is given by a = Fp/m. We can substitute Fp into this equation, giving us a = mgsinθ/m = gsinθ.Using the given angle of inclination of the plane (θ = 30°) and the acceleration due to gravity (g = 9.8 m/s²), we can calculate the acceleration of the ball as it rolls down the ramp:
a = gsinθ = 9.8 m/s² × sin(30°) ≈ 4.9 m/s²Therefore, the acceleration of the ball as it rolls down the inclined plane is approximately 4.9 m/s².About GravityGravity is a natural phenomenon whereby everything that has mass or energy in the universe—including planets, stars, galaxies, and even light—attracts one another. Gravity is useful for holding objects on the surface of the earth. If there is no gravitational force, objects will scatter and collide with each other. Objects on earth can also be thrown into space. The force of gravity keeps the atmosphere on the earth's surface.
Learn More About Gravity at https://brainly.com/question/940770
#SPJ11
We use monochromatic light of Wavelength λ=5.90×10^−7m in a double slit experiment. Wefind that the fourth-order constructive interference occurs at an angle of 6.0^∘ . Now I want you to answer the following: (a) The required slit separation to achieve this result, and (b) the angle at which third-order Constructive interference will occur if We use the same slits but with a different light whose wavelength λ=6.50×10 ^−7m.
a) The required slit separation to achieve the fourth-order constructive interference at an angle of 6.0° with monochromatic light of wavelength λ=5.90×10⁻⁷m is approximately 9.83×10⁻⁶m.
b) With a different light source having a wavelength λ=6.50×10⁻⁷m, the angle at which third-order constructive interference will occur using the same slits is approximately 7.13°.
a) In a double-slit experiment, the condition for constructive interference is given by the equation: d × sin(θ) = m × λ,
where d is the slit separation, θ is the angle of the interference pattern, m is the order of the interference, and λ is the wavelength of the light.
Given that the fourth-order constructive interference occurs at an angle of 6.0° (converted to radians: 6.0° × π/180 ≈ 0.105 radians) and the wavelength is λ=5.90×10⁻⁷m, we can rearrange the equation to solve for the slit separation:
d = (m × λ) / sin(θ),
d = (4 × 5.90×10⁻⁷m) / sin(0.105),
d ≈ 9.83×10⁻⁶m.
b) Using the same slits but with a different light source having a wavelength λ=6.50×10⁻⁷m, we can determine the angle at which third-order constructive interference occurs. Rearranging the equation as before:
θ = arcsin((m × λ) / d),
θ = arcsin((3 × 6.50×10⁻⁷m) / 9.83×10⁻⁶m),
θ ≈ 7.13°.
To know more about monochromatic light refer here:
https://brainly.com/question/32064872#
#SPJ11
a. Explain the meaning of the symbol on the left of the letter B in the diagram above. (1) b. State in which direction the force F acts. (2) c. Calculate the magnitude of the force F on the wire if the strength of the uniform magnetic field surrounding the current carrying wire is 420mT, the current is 13 A and 12 cm of the wire is experiencing this field. (3)
(a) The symbol on the left of the letter B in the diagram represents a uniform magnetic field.
(b) The force F acts perpendicular to both the direction of the current and the magnetic field.
(c) The magnitude of the force F on the wire can be calculated using the equation F = BIL, where B is the magnetic field strength, I is the current, and L is the length of the wire segment in the magnetic field.
(a) The symbol on the left of the letter B in the diagram represents a uniform magnetic field. A uniform magnetic field means that the magnetic field strength is constant throughout the region under consideration.
(b) According to the right-hand rule for magnetic fields, the force F on a current-carrying wire is perpendicular to both the direction of the current and the magnetic field. Therefore, the force F acts perpendicular to the plane of the diagram, either into or out of the page.
(c) The magnitude of the force F on the wire can be calculated using the equation F = BIL, where B is the magnetic field strength, I is the current flowing through the wire, and L is the length of the wire segment that is experiencing the magnetic field. Substituting the given values of B = 420 mT (or 0.420 T), I = 13 A, and L = 12 cm (or 0.12 m), we can calculate the magnitude of the force F using F = (0.420 T)(13 A)(0.12 m). Evaluating this expression gives the magnitude of the force F.
Learn more about magnetic field here:
https://brainly.com/question/30331791
#SPJ11
If a 220 V step down transformer is used for lighting eight 12 V, 20 W lamps, find the efficiency of the transformer when a current of 1 A exists in the primary coil.
If a 220 V step down transformer is used for lighting eight 12 V, 20 W lamps , the efficiency of the transformer is 72.73%.
A transformer can be described as a static electrical device that transfers electrical energy from one circuit to another through electromagnetic induction. The primary and secondary coils are the two main components. The efficiency of the transformer is the ratio of the output power to the input power.
The given data are: Primary voltage, V1 = 220 V
Primary current, I1= 1 A
Secondary voltage, V2 = 12 V
Power of each lamp, P = 20 W
Number of lamps, n = 8
The primary power is given by P1 = V1I1 = 220 × 1 = 220 W .
The secondary current is calculated as,
I2 = P/nV = 20/(12 × 8) = 0.2083 A.
The secondary power is given by P2 = nPI2 = 8 × 20 = 160 W.
Therefore, the efficiency of the transformer is given by η = P2/P1× 100= 160/220 × 100 = 72.73%.
For more such questions on transformer, visit:
https://brainly.com/question/30612582
#SPJ8
Given the Figure 2 below, find the net electric field
E
vector at point A due to a positive charge Q
1
=30μC and negative charge Q
2
=−20uC. Write down all the necessary equations and drawings. Remember that electric field vectors
E
should be given by magnitude and direction, (x \& y-components and/or an angle θ between the vector and positive x-axis).
The net electric field vector at point A, due to a positive charge Q₁ = 30 μC and a negative charge Q₂ = -20 μC, can be determined using vector addition.
To find the net electric field vector at point A, we need to consider the electric fields produced by each charge individually and then combine them using vector addition. The electric field at a point in space due to a point charge is given by the equation:
E = k * (Q / r²) * u
Where:
- E is the electric field vector
- k is the electrostatic constant (k = 9 x 10^9 N m²/C²)
- Q is the charge of the source
- r is the distance from the source charge to the point of interest
- u is the unit vector pointing from the source charge to the point of interest
Step 1: Electric field due to Q₁
The electric field at point A due to Q₁ can be calculated using the above equation. The magnitude of the electric field is given by:
E₁ = k * (Q₁ / r₁²)
Step 2: Electric field due to Q₂
Similarly, the electric field at point A due to Q₂ can be calculated as:
E₂ = k * (Q₂ / r₂²)
Step 3: Net electric field at point A
To find the net electric field at point A, we need to add the electric field vectors due to each charge. Since the electric field is a vector quantity, we need to consider both magnitude and direction.
To add two vectors, we can break them down into their x and y components. Assuming the x-axis points to the right and the y-axis points upward, we can calculate the x and y components of each electric field vector. Let's denote the x-component of a vector V as Vₓ and the y-component as Vᵧ.
The x-component of the net electric field at point A (Eₐₓ) is the sum of the x-components of the electric field vectors due to each charge:
Eₐₓ = E₁ₓ + E₂ₓ
Similarly, the y-component of the net electric field at point A (Eₐᵧ) is the sum of the y-components of the electric field vectors due to each charge:
Eₐᵧ = E₁ᵧ + E₂ᵧ
Finally, the magnitude and direction of the net electric field at point A can be calculated using the x and y components:
|Eₐ| = √(Eₐₓ² + Eₐᵧ²)
θ = atan(Eₐᵧ / Eₐₓ)
By calculating the x and y components and using the above equations, we can determine the net electric field vector at point A due to the given charges Q₁ and Q₂.
Learn more about Electric
brainly.com/question/33513737
#SPJ11
(10) A car is stopped for a traffic signal. When the light turns green, the car accelerates, increasing its speed from 0 to 5.44 m/s in 0.882 s. (a) What is the magnitude of the linear impulse experienced by a 69.3 kg passenger in the car during this time? Submit Answer Tries 0/10 (b) What is the average force experienced by the passenger? Submit Answer: Tries 0/10
(a)The formula to calculate the impulse experienced by a person is the product of force and time, i.e., Impulse = F * Δt.The passenger has a mass of 69.3 kg and there is an increase in the speed of the car, i.e., acceleration.
The impulse experienced by the passenger during this time can be calculated as follows;I = mΔvHere,m = 69.3 kg,Δv = 5.44 m/sSo, I = 69.3 kg × 5.44 m/sI = 376.992 kg.m/s.
Therefore, the magnitude of the linear impulse experienced by a 69.3 kg passenger in the car during this time is 376.992 kg.m/s.
(b)The formula to calculate average force is given as;F= Impulse / ΔtFrom part (a), Impulse = 376.992 kg.m/sΔt = 0.882 s.
So, the average force experienced by the passenger can be calculated as follows;F = 376.992 kg.m/s / 0.882 sF = 427.05 N.
Therefore, the average force experienced by the passenger is 427.05 N.
Learn more about average force here ;
https://brainly.com/question/24704743
#SPJ11
A 4.60 g bullet moving at 632 m/s strikes a 710 g wooden block at rest on a frictionless surface. The bullet emerges, traveling in the same direction with its speed reduced to 436 m/s. (a) What is the resulting speed of the block? m/s (b) What is the speed of the bullet-block center of mass? m/s
To solve this problem, we can apply the principle of conservation of momentum. To find the resulting speed of the block, we need to determine the velocity of the block after the collision.
we can write the equation for conservation of momentum in the x-direction as:
(m_bullet * v_bullet_initial) + (m_block * v_block_initial) = (m_bullet * v_bullet_final) + (m_block * v_block_final)
where:
m_bullet = mass of the bullet = 4.60 g = 0.0046 kg
v_bullet_initial = initial velocity of the bullet = 632 m/s
m_block = mass of the block = 710 g = 0.710 kg
v_bullet_final = final velocity of the bullet = 436 m/s
Substituting the known values into the equation and solving for v_block_final, we get:
(0.0046 kg * 632 m/s) + (0.710 kg * 0 m/s) = (0.0046 kg * 436 m/s) + (0.710 kg * v_block_final)
0.0029072 kg·m/s = 0.0020056 kg·m/s + (0.710 kg * v_block_final)
0.0009016 kg·m/s = 0.710 kg * v_block_final
v_block_final = 0.0009016 kg·m/s / 0.710 kg
v_block_final ≈ 0.00127 m/s
(b) The speed of the bullet-block center of mass can be calculated using the conservation of momentum equation in the x-direction:
(m_bullet * v_bullet_initial) + (m_block * v_block_initial) = (m_bullet + m_block) * v_center_of_mass
we have:
(0.0046 kg * 632 m/s) + (0.710 kg * 0 m/s) = (0.0046 kg + 0.710 kg) * v_center_of_mass
2.9152 kg·m/s = 0.00531 kg * v_center_of_mass
v_center_of_mass = 2.9152 kg·m/s / 0.00531 kg
v_center_of_mass ≈ 549.055 m/s
To know more about momentum follow:
https://brainly.com/question/30677308
#SPJ11
2) You are watching a jet ski race. A racer speeds up from rest to 70mph in just a few seconds, then continues at a constant speed. Draw the motion diagram, the position versus time graph, the velocity vs time graph and the acceleration vs time graph for the jet ski.
These diagrams represent the motion of the jet ski as described in the problem, starting from rest, accelerating to a constant speed, and then maintaining that speed.
Motion Diagram:
The motion diagram shows the position of the jet ski at different time intervals. Since the jet ski starts from rest, we can represent it as follows:
Constant Speed
The "o" represents the starting position of the jet ski, and the arrow indicates the direction of motion. As time progresses, the jet ski moves to the right.
Position vs. Time Graph:
Since the jet ski starts from rest and then continues at a constant speed, the position vs. time graph would be a straight line with a positive slope (representing constant velocity). The graph would look like this:
markdown
Velocity vs. Time Graph:
The velocity vs. time graph would show the change in velocity as a function of time. Since the jet ski starts from rest and then maintains a constant speed, the graph would be a step function. It would show an instant increase in velocity from zero to a constant value and then remain constant. The graph would look like this:
markdown
Acceleration vs. Time Graph:
Since the jet ski starts from rest and then maintains a constant speed, the acceleration vs. time graph would be zero throughout. It would be a horizontal line at zero acceleration. The graph would look like this:
markdown
Acceleration
These diagrams represent the motion of the jet ski as described in the problem, starting from rest, accelerating to a constant speed, and then maintaining that speed.
To know more about acceleration
https://brainly.com/question/460763
#SPJ4
Which of the following statements on du is false?
A. cv is heat capacity at constant volume.
B. du is independent on pressure as it is only a function of T and p.
C. The equation shows that du depends on T and v.
D. Despite pressure is not shown in this equation, du is usually dependent on pressure if we choose T and p as independent variables.
The false statement among the options is B. The statement "du is independent of pressure as it is only a function of T and p" is incorrect.
In thermodynamics, the differential of internal energy (du) is given by the expression:
du = TdS - pdV
This equation shows that du depends not only on temperature (T) and pressure (p) but also on entropy (S) and volume (V). The du term represents the infinitesimal change in internal energy of a system.
The first term, TdS, accounts for the heat transfer into the system, where T is the temperature and dS is the infinitesimal change in entropy. The second term, -pdV, represents the work done by the system against external pressure, where p is the pressure and dV is the infinitesimal change in volume.
Therefore, du is not independent of pressure. The presence of the -pdV term in the equation clearly indicates that pressure has an impact on the change in internal energy.
While it is true that du can be expressed as a function of T and p alone (assuming constant entropy and volume), it does not imply that du is independent of pressure in general. The specific conditions and constraints of a system determine the dependence of du on various variables.
Learn more about internal energy here:
https://brainly.com/question/11742607
#SPJ11
What was the average acceleration of the driver during the collision? Express your answer using two significant figures. A car traveling 87 km/h strikes a tree. The front end of the car compresses and the driver comes to rest after traveling 0.92 m. X Incorrect; Try Again; 4 attempts remaining Part B Express the answer in terms of " g 's," where 1.00 g=9.80 m/s
2
. Express your answer using two significant figures.
Convert the initial velocity from km/h to m/s:
u = 87 km/h
u= 87 × (5/18) m/s
u= 24.17 m/s.
Determine the final velocity: v = 0 m/s.
Calculate the displacement: s = 0.92 m.
Use the formula v² = u² + 2as to find the average acceleration during the collision.
Substituting the values: 0² = (24.17)² + 2a(0.92)
Solve for a: a = -(24.17)² / (2 × 0.92) ≈ -315.11 m/s².
The negative sign indicates deceleration or negative acceleration.
Express the acceleration in terms of 'g' (acceleration due to gravity).
Given 1 g = 9.80 m/s², we can convert the acceleration.
Calculate a in terms of 'g': a = (-315.11 m/s²) / 9.80 m/s²/g ≈ -32.16 g's.
The negative sign still indicates deceleration.
Therefore, the average acceleration of the driver during the collision is approximately -315.11 m/s² or -32.16 g's.
To know more about initial velocity visit :
https://brainly.com/question/28395671
#SPJ11
A disk with a mass of M-10kg is supported by a frictionless axle and positioned in a vertical plane. A mass of m=120g is tied to a string and wrapped around a small groove at the edge of the disk. Determine the tension T experienced by the string in [N] after the mass is released from res. The moment of inertia is I=1/2 mr^2
To determine the tension experienced by the string, we need to consider the forces acting on the system.
When the mass m is released, it will accelerate downwards due to the force of gravity. This downward acceleration will cause a torque on the disk, which will result in angular acceleration.
The tension in the string will provide the torque necessary to accelerate the disk. The torque due to the tension can be calculated as the product of the tension T and the radius of the disk r.
The gravitational force acting on the mass m will also contribute to the torque. The weight of the mass m can be calculated as mg, where g is the acceleration due to gravity.
In rotational equilibrium, the torque due to the tension and the torque due to the weight of the mass m must balance. Therefore, we can write:
Tension × radius = Weight of mass m × radius
Solving for the tension T, we have:
T = (Weight of mass m) × (radius / radius)
Substituting the given values and performing the calculations will yield the tension T experienced by the string in newtons.
To learn more about tension experienced, you can visit
brainly.com/question/33262343
#SPJ11.
The emf of the battery in the circuit below is 30 V and the internal resistance of the battery is zero. R _1 =2 Ohms and
R _2 =1 Ohms: Find the total resistance of the network. Find the current flowing through the battery in the circuit.
The total resistance of the network is 3 Ohms. The current flowing through the battery in the circuit is 10 Amperes.
To find the total resistance of the network, we can use the formula for resistors in series:
R_total = R_1 + R_2
R_1 = 2 Ohms
R_2 = 1 Ohm
Substituting the given values into the formula:
R_total = 2 Ohms + 1 Ohm
R_total = 3 Ohms
Therefore, the total resistance of the network is 3 Ohms.
To find the current flowing through the battery in the circuit, we can use Ohm's Law:
I = V / R
I is the current
V is the voltage (emf) of the battery
R is the total resistance of the network
V = 30 V
R = 3 Ohms
Substituting the given values into the formula:
I = 30 V / 3 Ohms
I = 10 Amperes
Therefore, the current flowing through the battery in the circuit is 10 Amperes.
To know more about current, refer here:
https://brainly.com/question/15126283#
#SPJ11
What happens to the period of a pendulum: a) if its amplitude (the angle) changes slightly b) if its length changes c) if it's mass changes 2.Could you prove the relation between period and length of the pendulum in the experiment? Explain
If the amplitude (the angle) of a pendulum changes slightly, the period of the pendulum remains nearly unchanged. The period of a pendulum is directly proportional to the square root of its length. If the length of a pendulum changes, the period will also change. The mass of a pendulum does not affect its period.
a) If the amplitude (the angle) of a pendulum changes slightly, the period of the pendulum remains nearly unchanged. The period of a simple pendulum (under small angles) is primarily determined by its length, not by the amplitude. As long as the amplitude remains within the small-angle approximation, the period remains constant.
b) The period of a pendulum is directly proportional to the square root of its length. If the length of a pendulum changes, the period will also change. According to the equation for the period of a simple pendulum:
T = 2π√(L/g)
where T is the period, L is the length of the pendulum, and g is the acceleration due to gravity. As the length of the pendulum increases, the period also increases, and vice versa.
c) The mass of a pendulum does not affect its period. The period of a simple pendulum is solely determined by its length and the acceleration due to gravity. The mass of the pendulum does not appear in the equation for the period, so changing the mass does not change the period.
To experimentally verify the relation between the period and length of a pendulum, you can perform the following steps:
Set up a simple pendulum by suspending a mass (bob) from a fixed point using a string or rod.
Measure the length of the pendulum, which is the distance from the point of suspension to the center of mass of the bob.
Use a stopwatch or timer to measure the time it takes for the pendulum to complete one full swing (i.e., from one extreme to the other and back).
Repeat the measurement for different lengths of the pendulum, ensuring that the amplitude of the swings remains small.
Record the lengths of the pendulum and the corresponding periods.
Plot a graph of the period (T) versus the square root of the length (√L).
The graph should show a linear relationship, indicating that the period of the pendulum is proportional to the square root of its length.
Calculate the slope of the graph, which should be close to 2π√(1/g), where g is the acceleration due to gravity.
Compare the experimental results with the theoretical equation T = 2π√(L/g) to verify the relation between the period and length of the pendulum.
By conducting this experiment and analyzing the data, you can demonstrate the relationship between the period and length of a simple pendulum.
To learn more about pendulum click here
https://brainly.com/question/29702798
#SPJ11
You are standing 24.1 meters away from Brown Hall. After your physics exam you want to kick a ball at the building. You kick the ball with an initial velocity of 26.7 m/s and at an angle of 33 degrees above the horizontal. Give two decimal places for your answers. What is the x-component of the initial velocity, ∼m/s What is the y-component of the initial velocity, X m/s How much time does it take for the ball to reach the building? - seconds How high up the wall, does the ball hit the building? x meters
Answer:
I apologize, it looks like my previous response was cut off. Here are the full answers to the questions:
The x-component of the initial velocity is given by:
Vx = V0 cosθ
where V0 is the initial velocity and θ is the angle above the horizontal. Substituting the given values, we get:
Vx = 26.7 cos(33°) = 22.35 m/s (to two decimal places)
Therefore, the x-component of the initial velocity is approximately 22.35 m/s.
The y-component of the initial velocity is given by:
Vy = V0 sinθ
Substituting the given values, we get:
Vy = 26.7 sin(33°) = 14.13 m/s (to two decimal places)
Therefore, the y-component of the initial velocity is approximately 14.13 m/s.
To find the time taken for the ball to reach the building, we can use the equation for the time of flight of a projectile:
t = 2Vy / g
where g is the acceleration due to gravity. Substituting the given values, we get:
t = 2(14.13) / 9.8 = 2.88 seconds (to two decimal places)
Therefore, it takes approximately 2.88 seconds for the ball to reach the building.
Tofind the height at which the ball hits the building, we can use the equation:
y = h + Vy t - 0.5 g t^2
where h is the initial height of the ball (which we can assume is zero), and y is the vertical distance traveled by the ball. Substituting the given values, we get:
y = 0 + 14.13(2.88) - 0.5(9.8)(2.88)^2 = 18.05 meters (to two decimal places)
Therefore, the ball hits the building at a height of approximately 18.05 meters above the ground.
Explanation:
Standing waves of frequency 57 Hz are produced on a string that has mass per unit length 0.0160 kg/m. With what tension must the string be stretched between two supports if adjacent nodes in the standing wave are to be 0.71 meters apart?
The tension for a desired standing wave, use the wave equation and wave velocity equation. Given the distance between adjacent nodes and frequency, the tension is approximately 105.33 Newtons.
The tension required to produce the desired standing wave, we can use the wave equation:
v = √(F/μ)
where v is the wave velocity, F is the tension in the string, and μ is the linear mass density of the string.
The wave velocity is given by the equation:
v = λf
where λ is the wavelength and f is the frequency of the wave.
In the standing wave pattern, the distance between adjacent nodes is equal to half a wavelength. So, if adjacent nodes are 0.71 meters apart, the wavelength is 2 * 0.71 = 1.42 meters.
Substituting the values into the wave velocity equation, we have:
v = λf
v = 1.42 * 57
v ≈ 81.54 m/s
Now, we can rearrange the wave equation to solve for tension:
F = μv²
Substituting the values:
F = 0.0160 * (81.54)²
F ≈ 105.33 N
Therefore, the tension required to produce the desired standing wave is approximately 105.33 Newtons.
To know more about velocity ,
https://brainly.com/question/18084516
#SPJ11